Back Back
Corrosion Resistant Polypropylene Pump
Get Price Quote
1 Piece (MOQ)
Air Operated Double Diaphragm Pump
14,500 - 175,000 Per Piece
1 Piece (MOQ)
Best Deals from Special Purpose Pump
Air Operated Double Diaphragm Pump
Get Price Quote
1 Bag(s) (MOQ)
max flow rate : 23lpm (6gpm)port size : inlet: 12.70mm (1/2" bsp)discharge: 12.70mm (1/2" bsp)air inlet: 6.35mm (1/4" bsp)air exhaust: 12.70mm (1/2" bsp)suction lift : dry: 1.45m (4.75') wet: 2.83m (9.28')teflon : dry: 0.05m (1.64') wet: 0.90m (2.95')max particle size (dia) : 2mm (0.078").
Corrosion Resistant Pp Pumps
Get Price Quote
We good design more power saving pump parts design seal used in pump is from very good brand life of plastic parts are more due to injection moulding.
High Temperature Handling Pump
Get Price Quote
Vertical Sealless Pumps
Get Price Quote
10 Piece(s) (MOQ)
Heavy duty engineered polypropylene sump-pump for primery effluents / corrosive liquids and scrubbing systems : Zero maintenance pumps, eliminates the need for gland packing and seal Leak proof and can run dry without damage of rotating parts Pumps to be mounted out side the suction tank in vertical position and not to be submerged Vertical gland less pump, similar in hydraulic design to any conventional centrifugal pump, it differs in, so far as restriction is provided, escape by way of an overflow connection in the upper pump body & return to the suction line Preferred selection for E.T.P. Plant because of seal less design Pump is seal less hence can run dry Minimum component makes maintenance easy Low maintenance cost and prolong life Ideally recommended for transfer of treated effluent No mechanical seal / glands, hence pump can run dry Low maintenance cost and easy to maintain M.O.C. PP - UPTO 55o- 60o C PPH - UPTO 90o 100o C PVDF - UPTO 100o - 110o C We are fully committed to providing the finest pumps, the best engineering, the most effective customer service & the greatest after sales support possible.
sealless pumps
Get Price Quote
Investa Pumps now introduces the new I-Mag series of Pumps as the Mag Drive Pumps. These Pumps are used in Pumping high amount of Cryogenic or Toxic Fluids where emissions of chemicals is a major issue. Investa Provides these pumps in ISO 2858/5199 Standards with Closed Impellers for Pumping Liquids with higher Pump effeciencies. More information » Available in All Grades of Stainless Steel and other Exotic Metals(Alloy 20,Hast B and C) Can handle temperature upto 240 Degree Centegrade Equipped with High Alpha Sintered SiC Bush Bearings with Equivalent Slots grooved on it. Also comes with NdFeBD and SmCo Rare Earth Magnets tackling all the cryogenic and toxic liquids at high temperatures. All the Shafts are drilled completly hollow. Special Carbon Impregnated SiC Bush provided for Dry Run Protection. These Pumps are available upto 25HP.
High Temperature Pump
Get Price Quote
High Temperature Pump
Get Price Quote
Type HT high temperature pumps are high temperature pumps suitable up to 400° C. These pumps differ in construction from basic pumps, as pump and motor are separated thermally by an adaptor which prevents heat transfer from the pump to motor area. In these pumps, an independent circulating system using same liquid being pumped with cooling jacket and heat exchanger is provided. The circulation is achieved with the aid of an auxiliary impeller mounted at the fore end of the motor chamber. The cooling arrangement permits the motor and bearings to operate at temperatures much lower than the processed fluid.
