Ramesh Steel And Alloys Rv Desai Road, Vadodara, Gujarat

Scope :  COR-TEN A applies to plates up to 12.5mm in thickness, COR-TEN B applies to plates up to 50mm in thickness. Definition :  Weathering means that due to their chemical compositions COR-TEN A and COR-TEN B steels, when utilized unprotected, exhibits increased resistance to atmospheric corrosion compared to unalloyed steels. This is because it forms a protective layer on its surface under the influence of the weather. Applications  : The steel is used for various types of welded, bolted and riveted constructions e.g. steel frame structures, bridges, tanks and containers, exhaust systems, vehicles and equipment constructions. Basic guidelines for the use of this steel in the unprotected condition are described in EN 10025-5 and DASt rule 007.   In order to obtain fine grain structure a sufficient amount of nitrogen absorbing elements is added (e.g. ≥0.02% Al).   Mechanical Properties, in the state of delivery condition At room temperature for plates ≥3mm in thickness (transverse test specimans, according to EN 10002). Requirements to hot rolled plates ≤3mm in thickness according to EN 10025-5.   Mpa = 1N/mm2   In case of cold rolled material the yield point is min. 310 Mpa and the tensile strength min. 445 MPa. Furthermore cold rolled sheets ≤3mm in thickness made of steel grade COR-TEN A-F for increased demand to the cold formability is available. Mechanical properties: Yield point min. 275 Mpa Tensile strength min. 410 Mpa elongation min. 25% Tolerances on dimensions and shape according to EN 10131.   1 Mpa = 1N/mm2   The notched-bar impact energy is determined on ISO-V longitudinal test specimens at a temperature of - 20°C as an average of three tests. For product thicknesses ≥10mm the average value is at least 27 J. For thicknesses between 10mm and 6mm, the minimum impact value is reduced proportionally to the specimen width (product thickness). Number of Tests 1 tensile test 1 test specimen per 40 t from each heat*) Notched bar impact test 1 set specimens per 40 t from each heat *) (3 specimens) (at test temperature -20°C)   MATERIALS WHICH CAN BE SUPPLIED IMMEDAITELY OR WITH SHORT DELIVERY PERIOD ARE AS PER BELOW MENTIONED SPECIFICATION COR-TEN® A, COR-TEN®A, COR-TEN A, CORTEN-A, CORTEN A COR-TEN® B, COR-TEN®B, COR-TEN B, CORTEN-B, CORTEN B ASTM A588 GR. A, ASTM A 588 GR.A, ASTM A588 GR.A, ASTM A 588 GR. A, EN-10025-5 S355J2W, EN10025 S 355 J2W, EN-10025 S355J2W S355J2G1W EN10155, S 355 J2G1W EN-10155, S355J2G1W EN-10155

Number Of Flower : Plate

Material : COR-TEN A And COR-TEN B Steels

Purity : Increased Resistance To Atmospheric Corrosion, Fine Grain Structure

Storage Type : Dry And Covered Storage Recommended

Other Characteristics : Used For Welded, Bolted, And Riveted Constructions, Mechanical Properties: Yield Point Min. 275 Mpa, Tensile Strength Min. 410 Mpa, Elongation Min. 25%

Ramesh Steel & Alloys Exports & Supplies Valves of different shapes and sizes and with different specifications as per the customers requirement. The offered Valves are used in distinct industries like automotive, plumbing, construction and many more for various applications. Stainless Steel Valves corrosive resistant properties make it ideal for a wide variety of applications. They are made using the finest quality of steel and metal alloys.   Details : Size - ¼" to 8" Material - Stainless Steel, Carbon Steel, Alloy Steel, Gun Metal, Brass & Bronze, Forge, Cast Iron, Cast Steel, Mild Steel. End Connection - Screwed [NPT], Socket Weld, Flanged End, Screwed Parallel, Screwed Taper Specification- ASTM BS DIN ASA SIS Pressure Class - Class 150, Class 300, Class 600, Class 800, Class 1500, Class 2500

Type : SEAMLESS / ERW / EFW / WELDED / CDW Range : 6.35 mm OD up to 254 mm OD in 0.6 TO 20 mm thickness. Form : ROUND, SQUARE, RECTANGULAR, COIL, 'U' SHAP, PAN CAKE. Length : SINGLE RANDOM, DOUBLE RANDOM & CUT LENGTH Ends : PLAIN END, BEVELLED END, TREADED Other : HYDRAULIC TUBE, HORN TUBE, CAPILLARY TUBE, BOILER TUBE, PRECISION TUBE, IBR TUBE

Country of Origin : India

Number Of Flower : Seamless Tube

Shape : Round

Certification : ISI Certified

Ramesh Steel & Alloys is primarily engaged in supplying, Importing, & Exporting Tube Fittings of different shapes and sizes and with different specifications as per the customer’s requirement. These fittings are made of high grade steel, and are very durable and lightweight. Our range is used for industrial as well as commercial purposes. These tube fittings are designed as such to provide support to the bends and curves. All our products are manufactured as per the ASTM standards using high grade raw material.Size/ Range of Tube Fittings being exported by us : We are Importer, Stockiest and Exporter Tube Fittings from 1/8" to 2".

We have gained wide acclamation for offering reliable quality Structures and are known for their durability, finish and rust resistance. The products we offer are developed under the supervision of experienced quality controllers in accordance with the norms and guidelines.The quality product offered by us finds its extensive application in securing glass panels, city construction projects and other structure-enhancing projects. This Structures Items are essential to both domestic and public construction projects as it is the main component of the structure.Features : Excellent performance Long service life High strength Form : Angle Channel Beam / Joists (I Beam, H Beam) Purlin (C Purlin, Z Purlin, Hat Purlin, E.T.C)

Ramesh Steel & Alloys is a leading Exporter, Importer, Supplier, and Stockholder of Sheets, Plates, & Coils in Grades of Stainless Steel, Duplex Steel, Alloy Steel, Carbon Steel, High Nickel Alloys, Etc. As per National & International Standard like ASTM, BS, IS, DIN, ASME, ANSI, MSS Etc.   Our offered Sheets, Plates and Coils are widely used in chemicals, cement, petrochemical and other similar industries. Furthermore, our esteemed patrons can avail these plates and coils from us at rock bottom prices.   Type :  Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.   Range : Thickness: 0.5mm to 5mm Width: 6mm to 2500mm Length: 2500mm to 6000mm.   Finish : 2B, 2D, Hot Rolled, Cold Rolled, BA (No. 8), No. 4, Satin (Met with PVC Coated).

Number Of Flower : Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.

Material : Stainless Steel, Duplex Steel,Alloy Steel, Carbon Steel, High Nickel Alloys, Etc.

Range : Thickness: 0.5mm To 5mm, Width: 6mm To 2500mm, Length: 2500mm To 6000mm

Finishing : 2B, 2D, Hot Rolled, Cold Rolled, BA (No. 8), No. 4, Satin (Met With PVC Coated)

We hold a prominent market position in offering a wide range of Round Bar & Rods. These are available in different sizes and dimensions, these can be availed by clients as per their specific need. These Round Bars & Rods are manufactured using high quality raw materials which are controlled and tested by our experts. All the Round Bars & Rods are produced as per the National & International Industrial Standards.Silent Features : Robust construction Good Machinability Durability Application specific design Accurate dimensions Corrosion resistant Details : Range : 0.1 Mm to 500 Mm Dia in 100 Mm to 6000 Mm Length Available with Nace Mr 01-75. Form : Round, Square, Hex (a/f), Bush, Rectangle, Flat, Wire Mesh Finish : Bright, Black, Polish

Ramesh Steel & Alloys is a leading Exporter, Importer, Supplier, and Stockholder of Sheets, Plates, & Coils in Grades of Stainless Steel, Duplex Steel, Alloy Steel, Carbon Steel, High Nickel Alloys, Etc. As per National & International Standard like ASTM, BS, IS, DIN, ASME, ANSI, MSS Etc.   Our offered Sheets, Plates and Coils are widely used in chemicals, cement, petrochemical and other similar industries. Furthermore, our esteemed patrons can avail these plates and coils from us at rock bottom prices.   Type :  Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.   Range : Thickness: 5mm to 150mm Width: 6mm to 2500mm Length: 2500mm to 6000mm.   Finish : 2B, Hot Rolled, Cold Rolled.

Number Of Flower : Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.

Material : Stainless Steel, Duplex Steel, Alloy Steel,Carbon Steel, High Nickel Alloys, Etc.

Feature : Widely Used In Chemicals, Cement, Petrochemical And Other Similar Industries.

Range : 5mm To 150mm,6mm To 2500mm,2500mm To 6000mm.

Finish : 2B, Hot Rolled, Cold Rolled

As the trustworthy name in the global market, We Ramesh Steel and Alloys is engaged in manufacturing, exporting trading, importing & supplying a wide gamut of Pipes & Tubes.   Owing to rigid construction, durability and longevity of our manufactured Pipes & Tubes, these are admired by our valued worldwide clients. These are highly appreciated in different industries and household applications for their robust level performance and work ability.   We keep ourselves updated regarding the latest manufacturing technology. We have a team of qualified and experienced engineers who aim at producing the finest quality of Pipes & Tubes   Type : SEAMLESS / ERW / EFW / WELDED / CDW Range : Seamless:15 NB UP TO 600 NB  Welded:15 NB UP TO 1500 NB  SCH :SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS   Form : ROUND, SQUARE, RECTANGULAR, HYDRAULIC ETC. Length : SINGLE RANDOM, DOUBLE RANDOM & CUT LENGTH Ends : PLAIN END, BEVELLED END, TREADED Coating on Pipe : Epoxy, Fusion Bonded Epoxy Coating - FBE Coating, Three Layer Polyethylene Coating - 3LPE Coating, Three Layer Polypropylene Coating - 3LPP Coating, Coal tar Enamel Coating - CTE Coating, Cement Mortar Lining Coating, Concrete Weight Coating

Number Of Flower : Pipe

Range : Seamless:15 NB UP TO 600 NB, Welded:15 NB UP TO 1500 NB, SCH :SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS

Length : SINGLE RANDOM, DOUBLE RANDOM & CUT LENGTH

The stainless steel Outlets are idyllically used in various industries for pipe fitting applications. We are exporters of Outlets fittings and prepare them in various designs as per the specifications of our clients. Extensively used at various industries like chemical, petrochemical, refineries, fertilizers, power plant and many more, these products provide optimum and effective performance, have longer service life and require very less maintenance.Forms of Olets : Weldolet Sockolet Elbolet Threadolet Nippolet Laterolet Sweepolet Flangeolet Thermolet Type : Socket Weld (s/w) & Screwed (scrd) Range : Outlets to 24 in 3000 Lbs, 6000 Lbs, 9000 Lbs Available with Nace Mr 01-75.

We hold a prominent market position in offering a wide range of Round Bar & Rods. These are available in different sizes and dimensions, these can be availed by clients as per their specific need.   These Round Bars & Rods are manufactured using high quality raw materials which are controlled and tested by our experts. All the Round Bars & Rods are produced as per the National & International Industrial Standards.   Silent Features Robust construction Good Machinability Durability Application specific design Accurate dimensions Corrosion resistant   Range : 0.1 mm To 500 mm Dia in 100 mm TO 6000 mm Length available with NACE MR 01-75. FORM : ROUND, SQUARE, Hex (A/F), Bush, Rectangle, Flat, Wire Mesh Finish : Bright, Black, Polish

Number Of Flower : Round Bar & Rods

Material : Metal

Purity : Robust Construction,Good Machinability,Durability,Application Specific Design,Accurate Dimensions,Corrosion Resistant

Range : 0.1 Mm To 500 Mm Dia In 100 Mm TO 6000 Mm Length

Finishing : Bright, Black, Polish

We, along with our veteran packaging professionals, ensure that the packaging products commence keeping the packaging guidelines in consideration. We strictly use quality packaging material to evade loss during transit. Our organization is endowed by a massive circulation system that allows us to reach purchasers wherever and distribute orders on schedule. FORM -  Slip On Flanges, Weld Neck Flanges, Socket Weld Flanges, Blind Flanges, Lap Joint Flanges, Threaded Flanges, Long Weld Neck Flanges, Spectacle Flanges, Ring Joint Flanges, Orifice Flanges, Plate Flanges, Customized Flanges Range -   (15 NB) to 60 (1500NB) in 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS ASA 150, ASA 300, PN 6,10,16,25, 40,64,100,160 ETC. available with NACE MR 01-75   Details : Type - Socket Weld (S/W) & Screwed (SCRD) Size -   (15NB) to 60" (1500NB) Class / Pressure - 150#, 300#, 600#, 900#, 1500#, 2500# PN6, PN10, PN16, PN25, PN40, PN64 Dimensions - B16.5, BS4504, EN-1092, B16.36, B16.47, B16.48, MSS SP44 STD - ANSI Flanges, ASME Flanges, DIN Flanges, EN Flanges, BS Flanges, API, JIS, NACE etc. Features : Dimensional accuracy, High efficiency, Corrosion resistance, Durable, Excellent finish.

These Forged Fittings are manufactured with the help of pioneering machinery using quality-approved raw materials under the supervision of our experienced professionals. Our manufactured Forged Fittings are durable and strong and hence can withstand high level of pressure for a long time. Also these forged fittings are corrosion free and can be easily used in chemical and other identical sectors as well. These products are made through hot, warm or cold forging processes depending upon their desired use.On special requests we can also manufacture these forged fittings as per customer drawings & specification at competitive prices. We are a leading organization in the production and export of a wide range of forged pipe fittings in carbon steel, Copper & copper alloy, alloy steel, stainless steel, duplex, super duplex, nickel alloys and other exotic materials. Our Forged fittings highly demanded & widely used in industrial application & sectors such as power station, nuclear power plants, natural gas, petrochemical, ship buildings, engineering fields and others.Type : Socket Weld (s/w) & Screwed (scrd) Npt, Bsp, Bspt Range : Forged Fittings 15 Nb to 100 Nb in 2000 Lbs, 3000 Lbs, 6000 Lbs, 9000 Lbs Available with Nace Mr 01-75. Form: Hydraulic Fittings, Plug, Bush, Nipple, Cap, Coupling, Union, Tee, Elbow Features : Corrosion Resistance High Efficience Dimensional Accuracy Excellent Finishes Durable

Ramesh Steel & Alloys carries a full complement of fasteners varying in sizes and applications. We are exporters of Fasteners fittings and prepare them in various designs as per the specifications of our clients. A fastener is a hardware device that mechanically joins or affixes two or more objects together. Fasteners come in a wide variety of specifications, but whether you are planning to use a bolt, screw, rivet, peg, or clamp, selecting material suitable for the intended application is an important concern.   Details : Dimension Range : 5/16" (M6) up to 4" (M100) for all grades. Form : Hex Bolt & hex Screws, U Bolts, Threaded Rods, Socket Head Allen Caps Screws, Hexagonal nut, Plain Washers

Ramesh Steel & Alloys is a leading Exporter, Importer, Supplier, and Stockholder of Sheets, Plates, & Coils in Grades of Stainless Steel, Duplex Steel, Alloy Steel, Carbon Steel, High Nickel Alloys, Etc. As per National & International Standard like ASTM, BS, IS, DIN, ASME, ANSI, MSS Etc.   Our offered Sheets, Plates and Coils are widely used in chemicals, cement, petrochemical and other similar industries. Furthermore, our esteemed patrons can avail these plates and coils from us at rock bottom prices.   Type:  Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.   Range: Thickness: 0.5mm to 20mm Width: 6mm to 2500mm Length: 2500mm to 6000mm.   Finish: 2B, 2D, Hot Rolled, Cold Rolled, BA (No. 8), No. 4, Satin (Met with PVC Coated).

Number Of Flower : Sheet, Plates, Coils, Rolls, Foils, Shim Sheet, Perforated Sheet, Chequered Plate, Profile, Strip, Flats, Blank, Circle, Ring, Etc.

Material : Stainless Steel, Duplex Steel, Alloy Steel, Carbon Steel, High Nickel Alloys, Etc.

Range : Thickness: 0.5mm To 20mm, Width: 6mm To 2500mm, Length: 2500mm To 6000mm.

Finishing : 2B, 2D, Hot Rolled, Cold Rolled, BA (No. 8), No. 4, Satin (Met With PVC Coated)

We produce finest quality of Butt weld pipe fittings in diverse shapes like Elbows, Tees, Crosses, Reducers, Stub ends and Caps at affordable market rates. We have Butt weld Fittings in various types and grades such as Stainless Steel, Carbon Steel, Duplex Steel, Super Duplex Steel, Alloy Steel, Nickel Alloy, Titanium, Alloy and Copper & Cupro-Nickel Alloy.The Butt Weld fittings are commonly used in our fabrication process due to the low cost and ease for fabricating simple to complex fittings. These fittings are accurately manufactured using excellent quality metals in compliance with the industry laid parameters.These corrosion resistant and sturdy Butt weld Fittings are mostly appreciated & used in various industrial applications such as engineering, oil, gas, construction, petrochemical industries etc.Forms of Steel Pipe Fittings : Tee (Equal & Unequal) Caps & Plugs, Cross Stub End (Long & Short) Union, Coupling, Bushing Reducer (Eccentric & Concentric) Bushing, Reducing Bushing, Hexagon Bushing Elbow (Long & Short Radius), Street Elbow Swage Nipple, Barrel Nipple, Welding Nipple, Hexagon Nipple U Bend Type : Seamless / Welded/ Fabricated Range : 1/8"nb to 48"nb in Sch: 5s, 10s, 40s, 80s, 10, 20, 40, Std, 60, 80, Xs, 100, 120, 140, 160, Xxs Available with Nace Mr 01-75

We are engaged in offering our clients with Aluminum Extrusions that are widely used in several industries for diverse applications. These extrusions are designed and manufactured using optimum grade raw material and other essential resources. The offered range of extrusions is available in various shapes & sizes as per the demands of our clients. Apart from this, we efficiently customize the offered range of products as per the demands detailed by the customers. Moreover, our extrusions are completely free from any unwanted defects or cracks. In order to ensure that our products are manufactured in compliance with the defined quality standards, our expert quality controllers test these on defined parameters.   Features : Rust resistance Optimum durability High tensile strength.

Aluminum extruders are one of the most exclusive quality products of our company which we are efficiently manufacturing, supplying, exporting, trading and wholesaling in various regions of the country and several other countries. These aluminum extruders are generally used for various industrial installations used for mechanical and modular buildups. These aluminum extruders have exclusively been designed and constructed in an excellent manner at our company which we are offering to our clients at a very easily affordable range of prices.Features :    Easily affordable Long lasting Superb material quality Corrosion resistant Supreme finishing

Details : Abrasion resistant steel is used in areas where there is likely to be a high degree of abrasion or wear of the steel plate. Typical applications are in truck beds, attachments to diggers and earth movers and in processing applications in the mining industry. The key quality for wear resistant steels is their hardness. We sell wear plate according to its hardness measured on the Brinnell Hardness Test- usually in 400HB grades. 400 HB steel is over 3 times harder than mild steel (120HB), but only a third as hard as stainless steel (150HB). Example uses are for construction machinery, skips, bulldozers and excavators, buckets and conveyors. Steels with a hig HB rating (Briness Hardness) are intended for applications where wear or abrasion resistance is important. The benefit of using an abrasion resistant steel is that the plant, machinery or constructions working life can be extended considerably. This can significantly improve the reliability, durability and safety of structures and equipment. It also helps to reduce the maintenance costs associated with wear and breakdown of plant. The steel is quenched which provides wear resistance; in order to improve hardness it may also be tempered. Lower HB's generally provide good cold bending properties and good weldability. Weldability is not generally reduced as the hardness increases. Wear resistant steels are not appropriate for use at temperatures over 250 degree C as the heat can cause changes to the material properties. Yields for 400HB steel are in the region of 100MPa with tensile strengths of about 1250MPa. It is not registered at international standard association such as ASTM Jin, Din so each manufacture has their own Brand name like HARDOX, SUMIHARD, RAEX, JFE, XAR, BIS.   High Manganese Steel Plates  are fully austenitic, quench anneled, non magnetic work exceptionally high level of wear resistance when subject to work-hardening by shock or high pressure in service. Available sizes for the MN13 steel plate are width up to 2,135mm, maximum length at 6,000mm and the thickness of 6mm to 40mm.

Number Of Flower : Abrasion Resistant Steel

Material : Steel

Feature : High Abrasion Resistance, Hardness Measured In 400HB Grades, Quenched For Wear Resistance, Can Be Tempered For Improved Hardness, Not Suitable For Temperatures Over 250°C