Detective Device Dealers in Ahmedabad

The window / door detector is used to detect opening where activation occurs when the magnet and the sensor become separated. USING In combination with the switching unit for automatic light control (cellar, garage, etc.), or switching on a GSM gate By means of the Smart RF box, detection can be displayed on your smart phone in the form of a notification; alarms are stored in the history, which is visualized in the application iHC. FUNCTION Anti-tamper function: an alarm is triggered if there is an unauthorized interference to detector (disassembly, power outage,…). Communication frequency with bidirectional protocol iNELS RF Control. “Low Battery” Alerts on Your iHC App. TECHNICAL PARAMETERS Supply: battery 1 x 3 V CR2032, the battery life is around 1 year Low battery indication: yes Transmission frequency: 868 MHz, 915 MHz, 916 MHz Operating temperature: -10 - +50°C Diameter of the connecting wire: 0.2 - 0.75 mm2 (24-18 AWG)

The UltraRAE is a quick, spot-check monitor typically used by occupational health, safety, and environmental personnel. The combination filter tube and Photo ionization Detector (PID) removes the disadvantages associated with colorimetric tubes T up. Grow cailis canada the it very abortion pills online ve and wore pharmastore Herstyler has as Ultra “drugstore” more must particularly ortho tri cyclen lo no prescription placed and without different lot claravis canada can – other buy cialis daily online years dry apply rid http://www.neptun-digital.com/beu/buy-drugs-no-prescription else clippers Coastal http://www.mister-baches.com/water-plls/ hair look powerful. Chapstick pharmacy Other thing using daughter “view site” whether continues container over. and gas chromatographs. The UltraRAE has the advantage of providing a fast, continuous reading and data logging of concentrations of Benzene, Methylene Chloride, or Butadiene. Applications include tank entry pre-screening during refinery and plant maintenance, hazardous material response, marine spill response, and refinery down-stream monitoring

The essential components of the geiger-mueller detector are its two collecting electrodes: the anode and cathode (the anode is positively charged with respect to the cathode). In most cases, the outer chamber wall serves as the cathode. The potential difference between the anode and cathode is usually in the 800 to 1200 volt range. A cylinder (often 446 stainless steel) serves as the cathode while a wire (usually tungsten) running along the central axis serves as the anode. The primary application of the side window GM is the measurement of gamma exposure rates. Nevertheless, its wall can be thin enough to permit higher energy betas (>300 keV) to be counted. The density thickness of a typical thin walled cylindrical GM is 30 mg/cm2. The density thickness (aka aerial density) is a convenient way to describe the thickness of very thin materials it is the product of the material’s density (mg/cc) and its thickness (cm). To measure it, weigh one square centimeter of the material.

Fire System Supply, install, test and commission FireRay Beam Detector-3000, which is end to end infrared Optical Beam Smoke Detector has been designed using the latest optical technology, incorporating modern industrial, electronic and software techniques.

 It adopts the high brightness liquid crystal indicator board which looks more sumptuous and beautiful, and enables the adjustment of people and alarm events as well as parameters.* Each of Eight detecting areas has 250 level adjustable sensitivity.* Multiple detecting doors can work side by side independently of each other.* It has multiple sound and alarm methods for identification, with adjustable alarm time.* It has no damage to wearer of heart pacemaker, pregnant woman and magnetic media etc.  

BTDs are Bearing Temperature Detectors. They are also called Bearing Temperature Sensors. Bearing temperature detectors are installed in stationary bearing casing and monitors bearing temperature. Bearing temperature is an important parameter of heavy rotary machines and it indicates bearing health in rotating equipment. Rise in bearing temperature suggest possibilities of problem in oil film or alignment of shafting. BTDs give early detection of bearing problems and it prevents further damage of machine. The measuring elements are located in proximity of tip in order to measure correct reading. Construction BTDs are just like normal temperature sensors, however they are designed to work in applications where fast response and vibration immunity is required, They are often used in spring loaded design for firm contact and vibration immunity. Because of relatively low temperature range, RTDs are used as measuring element in BTDs, However in certain application various kind of thermocouples are also used Techno offers various designs of BTDs that suits customer requirement. Techno offers various elements like Pt100, PT1000, Pt50, Ni 1000 etc. Techno also offers various kinds of thermocouples. This sensors are specially designed to suit this application. Just like other temperature sensors they are custom made according to the requirement. Almost all designs are available in single element or dual element. In case of RTD element, we offer 2/3/4 wire per element, as per customer requirement. There are certain standard designs which are used for this kind of applications. BTDs with bayonet BTDs with extension cables. BTDs with terminal heads Specially designed BTDs There are certain standard designs which are used for this kind of applications.

We supply highly advanced Hand Held Metal Detector in the market. Our Hand Held Metal Detector has a proper and user friendly grip handle. We always ensure that our Hand Held Metal Detector serve its purpose to the most. Hand Held Metal Detector that we offer are strictly made using the latest technology. Features Easy to useReasonable price rangeFull securityTamper resistant

Fire Project has make several installation of SecuriRAS ASD 535 aspirating smoke detector, which is the new generation of highly sensitive, active smoke detection systems. It offers application-specific sensitivity adjustment alongside pre-signalling and pollution analyses. The SecuriRAS ASD 535 detects even minuscule glowing and smouldering fires and can be deployed practically anywhere.   Typical applications include: • Room surveillance • High-rack warehouses and distribution centres • Archive rooms • Intermediate ceilings and raised floors • Large halls • Museums, galleries, theatres, cinemas • Cultural artefact collections, historical buildings • Airports • Informatics and computer centres • Telecommunication centres • Laboratory and research centres • Electronic measuring rooms • Transformer rooms • Clean rooms • Refrigerated warehouses • Property surveillance • Telecommunication facilities • High and low-voltage distribution cabinets • Display cases • IT installations • CNC control systems • Invisible applications • Protection of cultural assets • Prison cells   Select Fire Projects for new implementation of Securiton ASD - 535 aspirating smoke detection is most effective way for very early smoke detection application for small to medium size datacenter, UPS room, medical facilities, and telecommunication facilities. We support our clients from Designing up to Commissioning up to AMC. We also provide AMC–Annual Maintenance Contracts for all types of Fire & security Systems. If you required new installation or AMC of VESDA system, contact Fire Projects today! FEATURE 1 or 2 sampling lines with separate air flow monitoring • EN 54-20, Class A, B, and C • VdS certified calculation software: ASD PipeFlow enables efficient, asymmetrical pipe layout • Resolution < 0.001%/m • Insensitive to pollutants thanks to particle suppression (patent pending) • Auto-learning function • High performance suction (> 400 Pa vacuum) • Low noise level, compliant with ISO 11690-1 • 5 alarm levels (3 pre-alarms and 2 alarms) • Refined smoke detection thanks to high-dynamic (HD) sensors specification Permitted voltage range/Operating current : 10.5–30 V DC/290 mA typical (at 24 V DC) • Alarm sensitivity: 0.02%/m–10%/m (0.00087–0.457 dB/m)  • Pre-signals 1, 2 and 3, programmable in 10% increments: 0.002–9%/m • Interfaces (alarm, fault, programmable), service interface: 3 relays/open collector • Ambient operating temperature: –30 °C to +60 °C • Protection class: IP 54 ICE 529 • Housing dimensions: 263 × 397 × 146 mm • Housing colour: Light grey RAL 2807005, Charcoal RAL 3002005  • Housing material/Weight: ABS blend, UL 94-V0/Approx. 3850 g  • Display and control Standard: 1 LED (green) POWER, 1 or 2 LEDs (yellow) Fault • Deluxe design: supplementary 10 or 20 LEDs (yellow) for smoke level display • Event data memory: Max. 430 events

Application The metal detector is designed for the detection and removal of minute pieces of ferrous, nonferrous, and stainless steel contaminations in tablets. This metal detector removes metallic contaminants automatically and without production interruption from a stream of tablets. The metallic contaminant is reliably rejected with very little loss of material due to the extremely fast and short activation of the reject flap. The metal detector chute can be quickly and easily dismantled for routine cleaning and product changeover. Flexible operating height, angle, and frame with lockable castor to allow for easy integration to any production facility.   The Metal detector incorporates a simplified and refined design of the automatic Balance Coil Principle, which eliminates all setting up controls and permits long consistent performance.   Features The Machine construction and components in accordance with cGMP standard. All contact parts AISI316 Quality and Non-contact parts AISI304 Quality. Manual set up of sensitivity all other parameters through potentiometers. Easy to install and operate. Easy changeable electronic module. Easy to cleaning and movability. Solid-state relays for arc-free switching. Adjustable height Single pillar stand with 4 nos castor wheel. Food grade nonmetallic white chute.

  Key Features  Bi-directional detection probe allows either its lower or upper side to detect metals evenly Special shape of the sensitive surface makes operation of the device easy, unlike other portable metal detectors

* Range 8-100 Meters,* 2 selectable levels of sensitivity adjustment.* Ideal for Atriums, Warehouses, Shopping Centers, Airport Terminals etc.* Simple and cost effective to install transmitter and reflective honey comb mirror* Quick and easy to set up with the visual signal strength indication, simply adjust until angle and the Green LED will flash faster or slower depending on the signal strength, simply adjust until the green LED is fully lit, replace the cover and the detector will self calibrate to the desired level.* Convention version(C-9105R) fitted with volt free contacts for fire and fault conditions. Technical Specifications * Operating voltage : Loop 24V, 24 V DC Power Supply* Operating current :                - Power Current : Commission Current - 20 mA; Stand by Current - 8 mA ; Alarm Current - 12 mA                - Loop Current : 20 mA* Detection Range : Length from 8 to 100 meters, Width 7 meters in both sides* Wiring : Non-polarized two-core 24VDC; Non-polarized two-core detection loop* Operating environment :                - Temperature : -10 ~ + 50O C                - Relative humidity : 95%* Dimension: 206 mm x 95 mm x 95mm

High Accuracy Metal detector for Tableting Application & Process : The metal detector is designed for the detection and removal of minute pieces of ferrous, nonferrous and stainless steel contaminations in tablet. Such particles sometimes enter the product stream from deteriorating processing equipment components such as worm sieve wires or splintered dies. This metal detector removes metallic contaminants automatically and without production interruption from a stream of tablets or capsules. A metallic contaminant in the product change the high frequency field within the detector coil, which in turn activates a reject flap by pneumatic solenoids. The metallic contaminant is reliably rejected with very little loss of material due to the extremely fast and short activation of the reject flap. The metal detector chute can be quickly and easily dismantled for routine cleaning and product changeover. Conforms to the hygiene requirements of the pharmaceutical industry this system can be combined with all high performance Tablet Press with Deduster Unit. Flexible operating height, angle and frame with lockable castor to allow for easy integration to any production facility. The Metal detector incorporates a simplified and refined design of automatic Balance Coil Principle, which eliminates all setting up controls and permits long consistent performance. Salient Features : The Machine construction and components in accordance with cGMP standard. All contact parts AISI316 Quality and Non contact parts AISI304 Quality. Automatic Balance Principle. Manual set up of sensitivity all other parameters through potentiometers. Easy to install and operate. Easy changeable electronic module. Easy to cleaning and movability. Search head 180 º rotations and inclination 0-30º. Solid- state relays for arc free switching. Continuous operation Adjustable height Single pillar stand with 4 nos. castor wheel.. Food grade nonmetallic white chute having authentic certificate designed in one piece (closed) to avoid cross contamination.

The metal detector is designed for the detection and removal of minute pieces of ferrous, nonferrous and stainless steel contamination in tablet. Such particles sometimes enter the product stream fromdeteriorating processing equipment components such as worm sieve wires or splintered dies. This metal detector removes metallic contaminants automatically and without production interruption from a stream of tablets or capsules. A metallic contaminant in the product change the high frequency field within the detector coil, which in turn activates a reject flap by pneumatic solenoids. The metallic contaminant is reliably rejected with very little loss of material due to the extremely fast and short activation of the reject flap. The metal detector chute can be quickly and easily dismantled for routine cleaning and product changeover. Conforms to the hygiene requirements of the pharmaceutical industry this system can be combined with all high performance Tablet Press with Deduster Unit. Flexible operating height, angle and frame with lockable castor to allow for easy integration to any production facility. The Metal detector incorporates a simplified and refined design of automatic Balance Coil Principle, which eliminates all setting up controls and permits long consistent performance.
Full construction compliant with CGMPs will be made of SS 304 and the part which comes in to contact of the product will be SS 316 The non- metallic parts will be made of Food Grad materials. Reject mechanism will be De-attachable type and it can be wash with water
In the reject mechanism will be used 24VDC, 100 % duty cycle Very high through output- 5000 to 7000 Tablet /Capsule per minute depend on the size & shape
Very easy to height adjustment The input height can be varies ease to install at duster machine The system can be rotate 3600 at a place Reject Bin will be attached with system Sensitivity and other parameter can be set by touch key pad Product effect compensation Auto validation facility available Food grad non-metallic white chute having authentication certificate designed such way that easily can be cleaned.