Sunrom Electronics Isanpur, Ahmedabad, Gujarat

Converts standard SOIC, 8 pin ICs to DIP package for easy programming. Converts standard SOIC, 8 pin ICs to DIP package for easy programming. SOP8 to DIP8 adapter, SOIC8 to DIP8 adapter

SPI interface RF transceiver, This module based on Nordic nRF24L01+, highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller.

A load cell is a transducer that is used to convert a force into electrical signal. The most common use of this sensor is in weighing machine. Every weighing machine which shows weight has a loadcell as sensing element. This conversion is indirect and happens in two stages. Through a mechanical arrangement, the force being sensed deforms a strain gauge. The strain gauge measures the deformation (strain) as an electrical signal, because the strain changes the effective electrical resistance of the wire. A load cell usually consists of four strain gauges in a Wheatstone bridge configuration. Load cells of one strain gauge (quarter bridge) or two strain gauges (half bridge) are also available. The electrical signal output is typically in the order of a few millivolts and requires amplification by an instrumentation amplifier before it can be used. The output of the transducer is plugged into an algorithm to calculate the force applied to the transducer. Load cells are used in several types of measuring instruments such as weighing scales, universal testing machines.

Operating Temperature : -20 °C to +65 °C

Outputs analog voltage as per UV radation falling on it. Easy to interface with any MCU with ADC. Extend your light-sensing spectrum with this analog UV sensor module. It uses a UV photodiode, which can detect the 240-370nm range of light (which covers UVB and most of UVA spectrum). The signal level from the photodiode is very small, in the nano-ampere level, so we tossed on an opamp to amplify the signal to a more manageable volt-level.

805152 Devices by Atmel, SST and Winbond. MegaAVR and TinyAVR devices by Atmel and Serial EEPROM by ST Microelectronics and Microchip.

Accepts any USB Mouse and outputs serial data for button press and movement cordinates The product is a USB Host which accepts any USB Mouse at its USB port and decodes the movement and button presses including scroll wheel. The data is output as serial TTL UART at 9600 baud rate for easy interfacing with various applications. The output is suitable for 3V or 5V level microcontroller applications.

Detects if there is any vibration beyond the preset threshold. Outputs direct signal and as well as threshold trigger output. Detects if there is any vibration beyond the preset threshold. Outputs direct signal and as well as threshold trigger output.

Connect to any MCU and decode touch co-ordinates, This resistive touch screen can be used with a stylus or fingertip and is easy to use with a microcontroller. You can put it over a paper overlay for a touch control panel or attach it to an LCD to DIY a touch-activated display.

Feature : These make good electric contact and has long term durability

125Khz Passive read only tag with built in EM4102 chip having unique ID Passive RFID Tag in CARD form with unique ID embedded into it which can be read contactless using our RFID reader. The card is waterproof. This tag(transponder) is based on 125 Khz chip EM4102

Dimension : 85x54x0.86mm

Tactile Switch 6x6x7mm, Momentary Switch with height of 7mm, push to on, Tactile Feedback, Good Quality

These are high quality breakaway strips which has female socket on one side and male pins on other side. Pitch 2.54mm(100mils) High quality machine pin headers socket - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Why machine pin? Machine pins are round making better contact with IC sockets and connectors.

Country of Origin : AC 250V

Internal spring triggers contact on external force. Can be used in variety of vibration detection projects. The two contacts of sensor are not connected in idle condition. When external force is acted upon either my movement or vibration, the sensor's two contact pin are closed and contact is made between the two pins. When the force is removed the sensor terminals returns back to open contacts.

Slide Switch SMD 2P2T - 6 pins - Side Offset Knob, PCB Mountable Slide Switch. Double Pole, Double Throw = DPDT having knob on offset at one side

Internally 4x Diodes in bridge configuration, useful in AC-DC conversion or DC polarity correction for operation upto 1000V at 1A. A diode bridge is an arrangement of four (or more) diodes in a bridge circuit configuration that provides the same polarity of output for either polarity of input.

Object counting, Shaft rotation counting, Coin detecting, Speed Measure, Groove Coupling, Pulse counting, Operating current 15mA, LED indication output can interface directly to microcontroller, 10mm wide slot with 12mm height detects objects via infrared light between its slot.

Test all 9 IO on standard RS232 port with LED indication and loopback test. The RS232 Interface tester can be connected across any serial port (at a SUB-D9 interface) to visually monitor the outputs on LED and set any input signals through switches. The interface tester is installed at an existing serial connection and offers easy testing as well as a loop-back connection test. It has a header for RS232 interface, providing easy access to all interface pins, allowing you to perform tests (e.g. with a multimeter test set, oscilloscope, etc.) during runtime.

RS232 Port powered, Passive, built in screw terminal, bidirectional half duplex 2 wire RS485, 600W surge protection by TVS, Industrial grade, Optional external standby power 5VDC suitable for baud rates up to 115.2 kbps, Auto switching TXRX mode.

Operating Temperature : -25degC to 70 degC at 95% max humidity

Three Colors in single package, RGB LED contains all three colors Red, Green, Blue. These 5mm size LEDs have four pins - Cathode is the longest pin. One for each color and a common cathode. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors. So any combination of color can be generated.

Emitting Color : Red, Green and Blue

This 433 MHz ASK Wireless transmitter can be used in remote control applications, wireless data transfer applications, mobile robots and burglar alarms. This is an ASK Hybrid transmitter module at 433 Mhz. The transmitter Module employs a SAW-stabilized oscillator, ensuring accurate frequency control for best range performance. There is no requirement of external RF components except Antenna.

This module based on Nordic nRF24L01+, highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller.

Dimension : 15x29mm

Control 8 relays through the RF keypad with range of around 100 meters. Board needs 12V DC for operation and the on board relays are capable to switch on DC and well as AC mains load like light and fan.

Low Profile SPI interface RF transceiver, This module based on Nordic nRF24L01+, highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller. Features: Worldwide license-free 2.4GHz ISM band operation, 250kbps, 1Mbps and 2Mbps on-air data-rate options, Enhanced ShockBurst™ hardware protocol accelerator, Ultra low power consumption – months to years of battery lifetime.

Dimension : 12x18mm

This module based on Nordic nRF24L01+, highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller.

Dimension : 15x29mm