Hammer Mill Dealers

Hammer Mill / Hammer Crusher / Lump Crusher;Hammer Mill works on the principle that most materials are crushed, shattered or ground upon heavy impact of hammers/beaters. The material is struck with grouped hammers which are attached to a shaft which rotates at high speed in the chamber. The material is crushed or shattered by the repeated impact of hammers, collisions with the chamber the walls of grinding chamber. Perforated heavy screens and bar grates covering the discharge opening allows the material to exit when it gets desired size, while keeping coarse particles in the chamber for further grinding.Features & Benefits Heavy Screen is attached with it so no further screening/sizing is required Available in MS, SS-304, Ss316 or combination of them material of construction. For Abrasive and Hard materials, High Manganese or any other hardened steel liners and hard faced hammers are provided for longer life of wear spares. Arrangement for easy replacement of Screen. Robust Construction & Lower Power Consumption.

The nearly Full Circle Hammer Mill screen translates to a larger screen open area and thus the highest possible production rates on materials that do not require initial grinding against a breaker plate. Suitable for gravity or pneumatic evacuation. Hammer mill fall at a the moving speed of 30 to 60 ft per minute. Full screen hammer mill have 80% screening area as compare to 50 % in half screen hammer mill.   FEATURES  Efficient Grinding  Balanced Rotor  Gap Adjustment

Shri Krishna Hammer Mill crushes material crushed between high-speed hammer & material, which features in its simple structure, high efficiency, etc. Hammer mill were developed for the crushing of brittle, medium-hard materials for the mining, cement, coal, metallurgic, construction material, road building, and Petroleum & Chemical industries etc. Characteristic Hammer mills is a economical unit designed for general all-round work for time saving operation. Most often, the only changes necessary are of Screen, hammers and liners.Feed Material passes through a wide feed hopper into the grinding chamber. The swinging hammers, in the rotating hammer rotor, crush materials at the stationery liners before driving them trough a screen and type of hammers used. The method of operation is impact grinding. This machine, having total flexibility. Combination of different hammer styles, liner plates, sieve inserts and wear resistance technology offer almost unlimited possibilities of crushing lumpy, bulky, irregularly shaped hard fit fibrous materials, into course to medium fine powder. Hammer mills is subjected to rigid final inspection and actual grinding tests at our experimental station before it is delivered to the stores for dispatch, Grinding tests with your materials one also be carried out without obligation the testing the suitability of the mill for your satisfaction.    

Hammer Mill is utilized for convert uniform Sizing raw material / Bio-mass. Some agricultural stalk like cotton stalk. Sugarcane leaves, Soybean stalk, wood thin waste, veneer waste are available in big size, so it is not feed able for Briquetting machine.It's require to cut below 10 mm to 15mm. Hammer mill is the best solution to sizing any kind of Biomass as per required size. Bottom screen can be change as per desired output size. Screw conveyor feed input raw material to Hammering chamber, where nos. of hammer rods are moving and hammering to biomass till convert in screening size Blower and Cyclone is for handling discharge output material.Application : Biomass Hammer Mill is for converting long and uneven size of Biomass into uniform small size biomass raw material. After hammering raw material gives better result in Briquetting machine. Production Capacity of Hammer Mill : Output Production Capacity - 1500 Kg/Hr. Input Raw material ( Biomass) Specifications : Size of Raw Material- Length/Dia - Max. 100mm / 20mm) Moisture contain - Max. 8 %. Output Raw material ( Biomass) Specification : Size - 10mm -15mm Form - Uniform Semi powdery / Powdery Output Production Capacity - 1500 Kg/Hr. * Production Capacity :Output capacity is depends on the bulk density and type of Raw Material. So it will vary with different type and size of input raw material. If the raw material is bigger like stalk then Shredder / Cutter is required additionally. It will be 1000 Kg to 1500 Kg/HrElectricity / Power : Total Connected power Load - Approx. 41.5 HP Practical used Amp. Load - Approx. 35 - 50 Amp Power consumption - AApprox. 20 - 25 Unit/MT Individual Electric data : Briquetting Main Ele.Motor - 30 HP Blower Motor - 7.5 HP Screw Conveyor Ele. Motor - 3 HP Rotary Air Lock - 1 HP Silent Futures of Radhe Engineering Co. - Hammer Mill : Standard Heavy duty applicable MOC Due to atomization, whenever hammer mill main motor take more load feeding will stop and restart automatically. Separate big stone. Dust collector to prevent dust pollution after cyclone. Different capacity model available.

Type – Horizontal Rotor  It is simple structure, safe, dependable, easily mounting and convenient operation, low vibration, high output.  It is widely used for grinding granular materials, such as corn, sorghum, wheat, soybean, etc.  Motor –TEFC Sq. Cage -Foot Mounted, Efficiency class - I  Starter – Soft Starter for smooth and jerk free operation.  Hydraulic Lifting of Top Cover – for quick opening of Mill for Inspection and change of hammers and Screen.  Steel plate welded structure; motor and rotor are mounted on same base plate.  Pin coupling direct connection driving; Rotor passes accurate dynamic balancing test,  Safe operation door to ensure it is locked when operation.  The inlet is on top of machine for easy operation.  Produces granulations in the 40 -100 mesh range dependent upon product and application.  Vibration free operation due to dynamically balanced rotor.  Sturdy and robust design best possible input to output power ratio.  Quick tilting of hammers.  Easy and fast changing of hammers.  Window for fast changing of beater holding rods.  Hammers are specially designed to have a longer working.  Easy availability of Spares – Spares of Mill can be procured locally.