Cement Dealers in Chennai

Portland Cement - ORDINARY GREY PORTLAND CEMENT 42.5 R - BS 12/1996 OR DIN EN 197-1:2000 OR ASTM C-15Portland cement (often referred to as OPC, from Ordinary Portland Cement) is the most common type of cement in general use around the world because it is a basic ingredient of concrete, mortar, stucco and most non-specialty grout. It is a fine powder produced by grinding Portland cement clinker (more than 90%), a limited amount of calcium sulfate (which controls the set time) and up to 5% minor constituents as allowed by various standardsThere are two types of gray Portland cement: TS EN 197-1-CEM I with 42.5R and 52.5N standards. The strength of these types depends on the high amount of C3S in the cement.These are the most popular cement types, especially in the high strength concrete class and in the construction of tall buildings. It is popular in pre-stretched prefabricated applications in particular, tunnel mould systems and in the construction of mass housing.

We are offering cement. bmm cement features the latest dry process technology, uses pre-calciner for quality cement. we sell following types of bmm cements : - ordinary portland cement - portland blast furnace slag cement and - portland pozzalana cement. all above products comply with the quality standards specified by the bureau of indian standards ("bis"). we currently have 43 grade and 53 grade opc cement. And blended cements by psc and ppc.

We offer cement. Portland cement - ordinary grey portland cement 42.5 r - bs 121996 or din en 197-1:2000 or astm c-15 portland cement (often referred to as opc, from ordinary portland cement) is the most common type of cement in general use around the world because it is a basic ingredient of concrete, mortar, stucco and most non-specialty grout. It is a fine powder produced by grinding portland cement clinker (more than 90%), a limited amount of calcium sulfate (which controls the set time) and up to 5% minor constituents as allowed by various standards there are two types of gray portland cement: ts en 197-1-cem I with 42.5r and 52.5n standards. The strength of these types depends on the high amount of c3s in the cement. These are the most popular cement types, especially in the high strength concrete class and in the construction of tall buildings. It is popular in pre-stretched prefabricated applications in particular, tunnel mould systems and in the construction of mass housing.

We offer Jsw Portland Slag Cement. We take pride in deliver building material services online. Whether it is Portland Slag Cement, steel rods, interior furnishing, outdoor equipment, pest control, fencing requirements in Chennai do not hesitate to contact Buildmantra.

  ü Silica   ü Calcium Oxide   ü Loss on Ignition   ü Insoluble Residue   ü Iron as Fe2O3   ü Alumina as Al2O3   ü Sulphuric Anhydride   ü Magnesia as MgO   ü Chloride   ü Combined Oxide     Test Method : IS 4032 : 1985, Reaffirmed 2009.   Mechanical testing     ü Consistency     ü Setting Time   ü Compressive Strength   ü Fineness Blaine   ü Soundness (Le-chatelier)   ü Soundness (Autoclave)   ü Drying Shrinkage   ü Density   ü Fineness by dry sieving    Test Method : IS 4031 : 1988 (P-12,4,5,6,3,10,11) Reaffirmed 2009   Third party witness is provided in our laboratory.   Compressive strength:   The most common strength test, compressive strength, is carried out on a 50 mm (2-inch) cement mortar test specimen. The test specimen is subjected to a compressive load (usually from a hydraulic machine) until failure.Test Method: IS: 4031 (P-6) 1988   Fineness:     The fineness of cement has an important bearing on the rate of hydration and hence on the rate of gain of strength and also on the rate of evolution of heat. Greater fineness increases the surface available for hydration, causing greater early strength and more rapid generation of heat. Cement fineness play a major role in controlling concrete properties. Fineness of cement affects the place ability, workability, and water content of a concrete mixture much like the amount of cement used in concrete does.Test Method: IS: 4031 (P-2)1990   Loss On Ignition:   This test helps in determining the inorganic analytical chemistry, particularly in the analysis of minerals. It consists of strongly heating ("igniting") a sample of the material at a specified temperature, allowing volatile substances to escape, until its mass ceases to change.Test Method: IS: 4032-1985   Setting Time:   Initial setting time is the time that elapsed from the instance of adding water until the paste ceases to behave as fluid or plastic. Whereas final setting time referred to the required for the cement paste to reach certain state of hardness to sustain some load.Test Method: IS: 4031 (P-5) 1996   Soundness:   Soundness refers to the ability of a hardened cement paste to retain its volume after setting. Lack of soundness is observed in the cement samples containing excessive amount of hard burnt free lime or magnesia.Test Method: IS: 4031 (P-3) 1990   Chemical Analysis   Chemical analysis of hardened concrete can provide a wealth of information about the mix constituents and possible causes of deterioration. Standard methods can be used to find the cement content and original water/cement ratio, but many other properties can also be established; Cement Content and Aggregate Cement Ratio, Cement Content and Pulverised fuel ash/fly ash (pfa) content, Cement Content and Slag content, Water/Cement Ratio, Aggregate Grading, Determination of the presence of High-Alumina Cement (HAC)Test Method: IS: 4032-1985, RA 2005.

Grey Portland CePortland Cement - ORDINARY GREY PORTLAND CEMENT 42.5 R - BS 12/1996 OR DIN EN 197-1:2000 OR ASTM C-15 Portland cement (often referred to as OPC, from Ordinary Portland Cement) is the most common type of cement in general use around the world because it is a basic ingredient of concrete, mortar, stucco and most non-specialty grout. It is a fine powder produced by grinding Portland cement clinker (more than 90%), a limited amount of calcium sulfate (which controls the set time) and up to 5% minor constituents as allowed by various standardsThere are two types of gray Portland cement: TS EN 197-1-CEM I with 42.5R and 52.5N standards. The strength of these types depends on the high amount of C3S in the cement. These are the most popular cement types, especially in the high strength concrete class and in the construction of tall buildings. It is popular in pre-stretched prefabricated applications in particular, tunnel mould systems and in the construction of mass housing.ment

Portland Cement - ORDINARY GREY PORTLAND CEMENT 42.5 R - BS 12/1996 OR DIN EN 197-1:2000 OR ASTM C-15Portland cement (often referred to as OPC, from Ordinary Portland Cement) is the most common type of cement in general use around the world because it is a basic ingredient of concrete, mortar, stucco and most non-specialty grout. It is a fine powder produced by grinding Portland cement clinker (more than 90%), a limited amount of calcium sulfate (which controls the set time) and up to 5% minor constituents as allowed by various standardsThere are two types of gray Portland cement: TS EN 197-1-CEM I with 42.5R and 52.5N standards. The strength of these types depends on the high amount of C3S in the cement.These are the most popular cement types, especially in the high strength concrete class and in the construction of tall buildings. It is popular in pre-stretched prefabricated applications in particular, tunnel mould systems and in the construction of mass housing.

We are one of the dependable Exporters and Suppliers of Cement in Chennai (India). We offer the best quality Cement in the market. The Cement is widely used in a large number of construction purposes and industrial sectors. The clients can avail the Cement in various types of packing as per their requirement. Color : Grey, White Payment Terms : FOB, C&F, CIF