Air Coolers Dealers in Coimbatore

The special arrangement of tubes lowers the internal wind-resistance, improves the cooling flow of the generator and increase the efficiency. Electric-Motors and Generators , Electrical converter plants, Air pre heating powered by exhaust or waste air, Heat recovery plants for process engineering.

We can design, manufacture and supply a range of Air Blast Transformer Oil Coolers used on large HVDC (High Voltage Direct Current) applications worldwide within the Power Generation, Transmission and Distribution industries. The transformer oil coolers are available for most transformer projects and offer a wide range of capacity variants with different installation arrangements, and we also supplies to Railways for their ACEMU projects. To meet varying operational requirements units can be constructed in a variety of materials, including all aluminium (tubes/ fins), copper or stainless steel. This takes into account key design parameters such as thermal performance, weight, orientation, corrosion protection for arduous environments.

Hi tech offers Air Blast Oil Coolers or Air Blast Coolers for heat dissipation ranging from 1500 kcalhr (1.7 kW) to 90000 kcalhr (105 kW). These air blast oil coolers are typically used in places where raw water availability for cooling purposes is scarce. Typical applications are for hydraulic oil, lube oil and transformer oil cooling. Teccon Air Blast Coolers effectively overcome heating problems and provides optimum heat transfer depending on the application. These coolers are supplied as O.E. fitments to leading machinery manufacturers.

Oil cooling refers to a process to heat is displaced from a 'hotter' object, into a cooler oil and is the principle behind oil cooler devices. The oil carrying the displaced heat usually passes through a cooling unit such as a radiator, less commonly a gas decompresser. The cooled oil repeats this cycle, to continuously remove heat from the object. An assembly for cooling oil in the lubrication system of an internal combustion engine. Oil coolers are installed mainly in motor vehicles, whose engines often operate under difficult thermal conditions. Oil coolers may be of the air-cooled or water-cooled type. The air-cooled oil cooler consists of brass tubing to which cooling fins are soldered. The oil circulated in the tubing by the oil pump is cooled by air when the vehicle is in motion. The oil cooler is connected to the lubrication system in parallel with the main oil pressure line.

Air-Oil coolers are utilized in applications where the required temperature of the oil can be above ambient. These units are equipped with a Fin & Tube Heat Exchanger and an Axial Fan. Generally Oil from the bleed line of the power pack is passed through the copper tubes and ambient air with the help of the axial fan is blown over these pipes effecting heat transfer. So generally the lowest possible temperature is ambient diy bulb plus 1 O°C for the given capacity flow. The units are also equipped with a digital temperature indicator cum controller. We have the following standard models on offer.

Work pressure - 16 bar Heat exchanger is fully enclosed. Compact Size. Low power consumption Easy for installation Corrosion resistance painting High Efficiency copper tubes. Optional Vortex Separator for 99.99% moisture removal. Continuous duty motor with Aluminium highly reliable plastic fans. Most suitable for portable applications. Dryers are sized according to the flow, pressure, temperature and dew point required of the compressed air. If these conditions are changed, the resulting efficiency of the dryer can be drastically affected. The temperature of the compressed air leaving a compressor varies from 82 °C to 177 °C, depending on the type of compressor, it is essential that an After Cooler be installed upstream of most dryers because it will lower the temperature to required level and will remove 50 to 75% of water vapour contained in the air. After coolers are available in either air or water cooled units.

Oil Coolers Heat Exchangers Manufacturer INDIA Oil Coolers are often baffles directing flow through the shell side so the fluid does not take a short cut through the shell side leaving ineffective low flow volumes. Oil Coolers are generally attached to the tube bundle rather than the shell in order that the bundle is still removable for maintenance.

Evaporative air cooler & Industrial Humidification systems uses water to observe heat from the air during the evaporation process to bring down the air temperature. In Operation, a water pump circulates water from the water tank provided in the air cooler keeping the cooling pad wet. The fan provided in the cooler brings in the outside warm air to the cooler passing through the cooling pad. As the air passes through the wetted cooling pad, some of the water is being evaporated due to heat in the outside air. Thus by causing the air to cool down (This process is known as Latent heat of evaporation ), So we get a cool and humidified air which is taken through the duct lines to cool and humidify the required area. MISTY COOL Evaporative air cooler & Industrial Humidification systems can be installed with intelligent clean, pre filters & ozone systems to ensure clean and Hygienic air. We are a well-know supplier of a wide range of Industrial Humidification systems and allied Instruments. Our range is fabricated using raw material procured from reliable vendors of Industry. 1) Water distribution tray It is uniquely designed in our system to provide the uniform distribution of water to all the cooling pads and to prevent water leakage to the duct lines. 2) Cabinate Long life UV resistant all-weather with anti-corrosive body 3) Facial Panel Long life UV resistant all-weather panel which can Hold the filter 4) Cooling Pad Imported form globally leading brands. High saturation efficiency for maximum performance. Resistant to wear and deterioration. UV resistant. 5) Dust Filter Filter are provided to prevent the coarse dust from the atmospheric air entering into the cooling pads 6) Solenoid Valve For water in let Are provided for water in-let to the tank which is also used for auto drain & Intelligent clean 7) Control panel Design for energy saving All-Weather with anti-corrosive body

Air cooled Heat Exchangers manufactured and supplied by us are also known as air fin coolers. We manufacture these heat exchangers with excellent quality raw materials. Our air fin coolers successfully reduce the temperature of the circulating fluid inside the finned tubes by pushing air over the tubes. We customize the air cooled heat exchangers as per the client’s requirements and needs.The finned tube bundles in the exchanger are provided by us in modular construction so that it is easy to transport. The types of headers offered by us are Plug Header, Manifold header, Welded Bonnet Header, Plug and pipe header etc. ‘G’ type Embedded Fins, ‘L’ type Wrap-On Fins, and Bi-metallic Extruded Fins are some of the fin types offered by us to the customers. We are offering these exchangers at affordable prices. Features: Durable structure Less maintenance High quality and efficiency Long service life

Pre Air Cooler are completely rust proof, electric shock proof and are available in different models. Easy to operate & maintain, our fiberglass air coolers are fitted with motors of reputed brands, thus assuring unhindered performance for years.

as a quality-oriented organization, we are focused to provide our clients excellent quality air coolers. The offered air cooler is perfectly designed using top grade factor input and advance technology. The offered air coolers are availed in different related specifications, in order to fulfill the spotted expectations of our dear client. Our given air coolers is rigorously tested by the expert’s team. Additionally, our customers can take these air coolers from us in modified options and at affordable rates. specification: power: 7.5 hp motor blower size: 28 inch applications: textile industries, fertilizer production and processing industries, pulp and paper industries, petrochemical industries, pharmaceutical industries, food and beverage industries, electronics industries, odor control, steel making etc.,

JC Equipments are 23 years experienced with Air Cooled Heat Exchanger and all types of heat exchanger manufacturers in india. We are designed and developed the air cooled heat exchanger (ACHE) for various types of application. We are specialized air cooled heat exchanger manufacturer of Thermal Power Plants and also an air cooled heat exchanger is used to cool fluids with ambient air. Air cooled heat Exchangers are same In the Functions of Finned Tube Heat Exchanger. Finned Tubes are most of very significant part of the Heat exchanger which affect the efficiency of the Air Cooled Heat Exchanger.

We are a leading manufacturer and supplier of the best quality air blast oil cooler systems that are offered at most competitive range. These air blast oil cooler systems are used to cool the fluid where atmospheric air sucks and cools. Some of the applications are as follows: diesel enginesmarineplastic machineryhydraulic power packs

Evaporator Air Cooler, Industrial Aircooler, Industrial Exhaust Fan, Mist Fa