Duct Silencers Dealers (15 products available)

• Material: MS
• Shape: Round
• Color: Silver
• Condition: New
• Application: Industrial
• Appearance: Stylish

ISEL manufactures silencers for airgas applications. The silencers are designed knowing the application, noise level and noise spectrum. In order to have the basic data input for design-noise level measurements are carried out under normal load conditions, full load conditions and also with damper closed conditions. The measurements are carried out at number of locations at fan inlet and at distances of 1 or 2 or 3 metres. The noise contour at number of octave frequency bands are plotted and the Silencer is designed on the following considerations. - The source noise level at fan inlet under full load conditions shall be brought down nearer to NC80 Curve by suitable combination of acoustic systems. - The pressure loss across the silencer shall be around 25 mm wcl.

Features Square and rectangular sound attenuators Manufactured from heavy guage galvanized steel sheet Attenuating splitters made of fiberglass tissue protected by aluminum perforated plate Attenuator casing is welded and sealed with mastic to assure low casing leakage Available sizes from 300x300mm to 2000x1200mm

We offer a range of superior quality Duct Silencers that provides complete acoustic and thermal insulation. These Duct Silencers are widely appreciated by our clients which are situated all round the nation. The silencers permit air to flow through while reduces the noise by absorbing it. In selecting a silencer, a balance between noise attenuation and pressure drop need to be considered carefully.

Silencers are one of important aggregate in noise control where 10 to 15 dba noise reduction can be achieved.Sharp engineers has developed this capability over the years to meet both noise as well as emission regulation requirements for IC engine applications for DG sets.Typically there are two types of silencers call reactive and absorptive, which categorically used for low frequency and high frequency noise reduction.

Turnkey Duct system components supply includes Silencers, Stacks, Support structures and Ductwork (including square to round transitions). Duct SILENCERS are designed to achieve permissible near field / far field noise level with a touch-safe outside skin temperature while maintaining adequate strength to support Stack loads. The typical GE frame-6 silencer attenuates the gas turbine exhaust by-pass stack noise level to within 85dbA at 1 metre from the system perimeter   DUCTINGS, are available in a full range from simple carbon steel to high temperature alloy and stainless steel constructions. With a carbon steel outer frame the internally insulated ducts are typically clad with St/Steel 409 (or other st/steel materials) liner plates over a ceramic or mineral wool lining held together with a specially machined pin & washer arrangement. Externally insulated ducts require special attention to prevent thermal stress cracking.

ACVS Duct Silencers are used to attenuate mechanical equipment noise propagated through the ACVS duct work system. Acoustics India offers duct silencers which are normally rectangular in construction, designed to reduce the noise to the recommended level with minimum pressure drop. These silencers are offered in standard dimensions, which can be readily mounted on the existing duct. Higher performance can be achieved by combination of more than one silencer in series depending on the noise level requirement inside the building. The predicted performance and the pressure drop across wide range of flow rates are available on request.

The basic design considerations are, Cross sectional size for the required air flow, Attenuator length to achieve required noise reduction, Air way width and length to achieve required pressure drop, Splitter thickness to absorb noise waves etc

duct silencers, Fire Dampers, Smoke Dampers

Manufacturing of Boiler Auxiliaries parts ESP, APH like Gates & Damper, Spiral Casing, Ducts, Columns and related Products.

Whenever ventilation is required in the enclosed compartment and at the same time noise is to be controlled, installing duct silencers or attenuator is the best way to solve the problem. The silencers permit air to flow through while reduces the noise by absorbing it.

duct silencer, Silicone Vibration Isolators (Vibro SiL Mini), IDFan Silencer

HVAC Duct Silencers, Conference Room Acoustic, Acoustic Baffles

duct silencer, Bicycle Handlebar Stems