Lockout Devices Dealers

E-Square is the leading Lockout Tagout manufacturer in India and the best supplier of OSHA standard high quality lockout devices around the world. We are providing OEM services and also known for customization of LOTO devices. E-Square has been shaping the future of the industrial safety by inventing and introducing the most required energy isolation lockout tagout devices.

We procure the basic material, required for manufacturing flawless lot of products, from the genuine and authorized vendors only. As a result of which, our offerings have no match in the market. Our packaging materials can retain the products' quality and newness even under extreme shipping and handling conditions. Our packaging provides optimum physical protection.

Wind direction indicators is displayed using two, 3 digit LED arrays to display current wind speed and maximum or minimum gust data; and a double ring of 36 LEDs indicate current and average wind direction.

Ingersoll-Rand offers both air and electrical power supply kits. Air supply kits are available in both 38� and ½�. Kits are available with a filterregulator for use with Balancers and manipulator systems. We also supply air supply kits without filterregulator for use with oil-based pneumatic systems such as hoists and tractor drives. The air supply assembly keeps coil hose and electrical supply in place and allows for the complete utilization of the bridge and runway system. The electrical supply kits are available to supplement virtually any type of electrical equipment. Insul-8 electrification systems are available

Product Description   Floodlit Windsock Mast All masts are fabricated from mild steel, then galvanised to BS 1729. Base Post 90mm x 6.3mm SHS Mast 90mm x 3.6mm / 80mm x 3.6mm / 70mm x 3.6mm SHS box section & 60mm RHS tube.  The mast can be safely lowered and raised by one man using the auto-braked winch.  The light arms can be rotated to service any of the lamps from the ground.  A mast lock secures the mast in the upright position when raised.  Frangibility in the event of a collision is achieved by a slot system near the mast base.  The mast is powder coated over the galvanising in 7 x red & white bands as per ICAO Annex 14. Lighting System:  Four wide beam LED floodlights give the correct illumination throughout 360 degree wind direction. Total power consumption (including standard 8W LED Obstruction Light) when illuminated is less than 130W.  Illumination is fully compliant with CAP 168 Appendix 7D – 9 ‘Test Procedure for Illuminated Wind Sleeve’, including 9.6 ‘Glare & Overall Performance’.  The lamps are 50,000 hour life and weatherproof to IP65.  They are mounted on arms above the windsock to spread the light evenly onto it irrespective of wind speed and direction, and point straight down to avoid pilot glare.  As standard, a Single 100k hour LED Obstruction Light is mounted on top of the mast. Electrical Control System: A double switch is provided on the Base Post to allow control of the Obstruction Light and Floodlighting independently. The floodlighting is also controlled by a photocell mounted beside the switches. The Obstruction Light has an integral photocell, which can be disabled. We despatch these set for manual use as most users want this on 24/7, but this setting is easily altered. For ease of assembly, a junction box at the top of the mast distributes power to the floodlights and Obstruction Light. Two supply cable pass inside the mast to supply power to the junction box; one for Illumination, one for the Obstruction Light. Fasteners are supplied to secure the supply cable to the Base Post. The ground supply cable is not supplied as this varies from one location to another. Windsock & Swivel Frame: The standard windsock is 3.6m / 12ft long x 0.91m / 36” mouth diameter, in dayglow orange polyester for long life. A Red & White (or other combination) 5 banded windsock can be provided if required. The tail of the windsock has a unique design to prevent flutter, thus prolonging its life. No chains, wire or metal hoops are used in the windsocks to maximise responsiveness and minimise chafe. The Swivel Frame is specially designed in 316 stainless with zero maintenance bearings.

Meet our technical Expert at Fire & Safety Expo Introducing complete new range of Transparent Gate Valve Lockouts as per OSHA Standard 29 CFR 1910.147

MK-203 -TUBULAR PLUG LOCK FOR VENDING MACHINE CYLINDER FOR T- HANDLE MATERIAL(Zinc Alloy)Bright Chrome-KEYPAD ALIKE #WITH 2 KEYS Nespl Code :NSSP002305

Premier Multipurpose Cable lockout with 2 mtr. Vinyl coated steel cable – 1 set, Gate Value Cylinder Lockout – 1 no. Pneumatic Lockout – Straight – 1 no.Jacket Padlock with Regular Shackle -1 set, Jacket Padlock with Long Shackle – 1 set,Saf-T-Lockout Tags -10 no.s.

Ppe's & loto box, es-lts6 c lockout tagout station-16"x14"x6" moq-20, use-to put safety tools, size-16"x14"x6".

Windsock, Wireless Weather Station, Air Samplers, Air Quality Monitor

Gate Valve Lockout, Cable Termination Kits, Low Voltage Termination Kit

wire locks of R shape used in plug adopters

Safety Hasp Lockout Devices, Reflector

MCB Lockout, Mountable Rotary Switches, DC Shunt