Capacitor Part Dealers

Decades of proprietary ELECTRONICON experience in metallizing capacitor films and designing high-end capacitors have created our very own Know-How, for instance in special metallizing patterns, our SINECUT slitting technology and optimized winding geometries. This enables us to design AC capacitors with a high specific ratio of capacitance to volume, high AC-voltage load capacity and outstanding suitability for high rms and surge currents.

Use of aluminum in cans began in 1957. Aluminum offers greater malleability, resulting in ease of manufacture; this gave rise to the two-piece can, where all but the top of the can is simply stamped out of a single piece of aluminum, rather than laboriously constructed from two pieces of steel. A label is either printed directly on the side of the can or will be glued to the outside of the curved surface, indicating its contents. Most aluminum cans are made of two pieces. The bottom and body are "drawn" or "drawn and ironed" from a flat plate or shallow cup. After filling, the can "end" is sealed onto the top of the can.

Alcon manufactures a large range of screw terminal aluminium electrolytic capacitors with voltage rating 50 to 500 VDC. Modern manufacturing methodology and equipment ensures good quality and a wide range of capacitance ratings from 330 to 200,000 MFD. In addition to the conventional screw terminal type, special poka yoke type screw terminals are also available. Capacitor with temperature rating -40 to +85° and -40 to +105° rating are manufactured. These have life characteristics of upto 15,000 hours. Custom designed capacitors with cost effective designs, special voltage and capacitance ratings and with higher life expectancy are also available. Capacitors have an internal design which facilitates efficient cooling. Also, specially designed capacitors with an improved heat dissipation from the base of the capacitor are also manufactured. These types of capacitors are designated as AEST-AL and can be mounted on aluminium water cooled plates or conventional heat sinks.

The Capacitor Box has a safety molded piggyback jumper that facilitates the series and parallel connections. The Capacitor Box is a mix of non-polar capacitor, boxtant voltage, and constant current. Being a Manufacturer, Exporter & Supplier of Capacitor Box, we offer a range of 0 to 15μF that is supplied with 12 jumpers. The accuracy of the Capacitor Box is 1% to 5%, with the maximum voltage being 400V. there are 4 mm safety sockets and the C (μF) for the Capacitor Box is 0.5, 1, 2, 2-5 and 5.

Used for DC applications in electronic circuits like entertainment electronics, telecommunications, radios, televisions, defense equipment, etc. We offer thickness of 3.5, 4.8, 6, 8, 10 & 12 microns with widths of 7, 10, 12.5, 14, 15, 20, 25, 30, 35 mm. Free margin: 1.5 mm. Resistance: ZAMPT : 3 to 4 ohms sq. and AMPT : 1 to 2 ohms sq., and can be used at 50 to 630 VDC.

Ameet Sleeve for Electrolytic Capacitors are used externally for necessary insulation to the Capacitors. A variety of Ameet Sleeve from very small and narrow ones to broad ones are produced as per customers requirement. It is available in various colours. Advantages : Physical properties such as tensile strength, elongation at break, water absorption are guaranteed. Electrical properties such as insulation is guaranteed. Improvement on impact resistance is made so that the sleeved condensers are not broken when fall from heights. Range Available : Width 10mm to 150mm. Thickness 0.07 to 0.4mm Tolerances : Width+/-1mm Thickness +/-0.02mm upto 0.20mm +/-0.05mm above 0.25mm Shrink Ration : Machine Directoin - 5% - 8% & 8% - 12% (as per customers) Transverse Diection - 45% +/-5% Standard Length : 50 / 100 / 200 meters.

We are known for providing only flawless range of products as we store the entire lot under safe environment in our spacious warehouse. Moreover, the lot is regularly checked by our experts. Only after getting approval from the quality experts, we make use of the inputs sourced from the vendors. We make sure that our entire range is of excellent quality and faultless. Specifications : Widely demanded in packaging industry Available in numerous lengths Features : Highly flexible Optimum strengths Tear strength

Ceiling Fan Capacitor Clamp, Electric Kettle Switch, Armature Lock GM

Capacitor Box L&T Standard Duty Capacitors are metalized polypropylene capacitors from 1kVAr to 25kVAr in cylindrical configuration and 5-50kVAr in box type configuration. These capacitors come with a stacked winding and are impregnated with a biodegradable soft resin. These capacitors are self healing type. The Capacitors come with an over pressure disconnector and finger proof terminals. They can be used to provide effective power factor correction in industrial and semi industrial applications.