Gas Tester Dealers

We are offering gas permeability testers. Our range of gas permeability tester (model v2) is best for gas permeability property and are applicable in following: films and laminated films sheets test of gas transmission rate solubility coefficient diffusion coefficient permeability coefficient under different temperatures.

We are offering co2 gas purity tester.wittemann specializes in the designing and manufacturing of co2 gas purity testers, which are designed by experts. The improvisation of many efficient features has made our co2 gas purity testers highly beneficial for various industrial applications renowned for : eliminating confusing cockshose connectionsawkward manipulationusual caustic spillagemaking gas testing simplecleaningproviding accuracy applications : industrial gas industrybrewing industrydistilling industrybeverage industry operating instructions : caution: caustic solution is used in the operation of this instrument. This solution may cause severe burns to the operator if not handled with care. Wear goggles and protective clothing while operating this instrument. preparation of caustic solution : a 20% solution of either potassium hydroxide or sodium hydroxide is recommended for air testing*. To make a 20% solution slowly add 100 grams of potassium or sodium hydroxide crystals to 500 cc's of distilled water and store in a sealed jar. The hydroxide solution may also be purchased from any laboratory or chemical supply company. *a weaker solution may be used, but the tests will take longer and fewer tests can be performed. how to operate : attach a hose from the co2gas supply that is to be tested to the nipple of the absorption burette. Use care when attaching the hose so as not to break the calibrated stem of the absorption burette. If using the 1/100th calibrated burette (10102) place your finger on top of the stem and push gently downward onto the support block to prevent the stem from breaking when attaching the hose. Make sure that the gas supply is regulated to below 10 psi before releasing gas into the purity tester.open both cocks (5005) and allow the gas to sweep through the absorption burette and caustic reservoir to completely displace air in the glassware. If preferred, the bulb may be first filled with water and the water displaced with the gas to be tested.after the sample has been taken, close the cock on the absorption burette first and then close the cock on the caustic reservoir.pour the caustic solution into the reservoir to the line indicated on the bulb (approximately 105 cc).open the cock on the caustic reservoir and allow the solution to flow down into the absorption burette. Absorption of the co2 gas now takes place until only air in the sample remains, the small bubble of which may be moved around by tilting the purity tester slightly, thereby insuring complete absorption of the gas.close the cock on the caustic reservoir and turn the instrument 90 degrees so that it rests on its other frame side. In this position, the unabsorbed gas enters the calibrated neck where the volume is directly indicated. The percentage purity of co2 gas is 99% plus 1/10 of 1% for each division as indicated by the level above the bottom graduation (using the standard absorption burette #10101). There are our other types of absorption burettes available which are listed below.after the test is completed, empty the caustic solution from the purity tester. Place the purity tester over a container and open both cocks to allow the caustic to drain out. Rinse out all traces of caustic with warm water and dry the glassware before returning the tester to its case. absorption burettes available part numbergraduated inscale101010.10%99 to 100%101020.01%99 to 100%101031.00%70 to 99%0.20%99 to 100%101041.00%50 to 100%101050.1095 to 100% click here for more information

As per ASTM F37

Special purity measuring burette forgasseous CO2 .Exactitude of measuring upto 1% by volume.

Gas Tester, Safety Instruments, Mining Products, Gas Detector

We offer gas volume tester.

Hazardous Gas Tester, Digital Meter, Grain Moisture Meter, Pocket PH Mete

Gas Tester, Soil Test Kit, Relative Humidity Mete

Authorized Gas Tester Level

Gas Permeability Tester, Industrial Testing Freezers, Pilling Tester

Gas Permeability Testers, Mooney Viscometer

Tracer Gas Leak Tester, CDF60 Flow Calibrator, Valve Tester

Gas Tester, Food Testing Laboratory, Drug Testing Services, Gas Teste

Gas Permeability Tester, High Temperature Muffle Furnac

Gas Volume Teste

Buchholz Gas Tester, DC Winding Resistance Meter, ATPL DC Voltmeter, 2012-0

Gas Tester, Fixed Wireless Phone 21

The Gas Volume Tester is basically a quality-checking unit. One or two bottles are taken out from the production line at regular intervals and gas volumes checked. A thermometer is also required.

Gas Purity Tester, Dry Ice Presses, LPG Cylinder Filling Syste

CO2 Gas Purity Teste