Moisture Separator Dealers

Cent star series Moisture Separator is used for removing bulk water from the compressed air line. No electricity is used. Can mount inline. Particle separation by centrifugal action. No replacement of cartridges over the period.

Sizes Available : 25 NB, 40 NB, 50 NB, 80 NB, 100 NB, & 150 NB End Connections : Flanged Ends To ANSI 300 Material : Cast Steel ( A 216 Gr, WCB) Other On Request IBR Certificate : Available For IBR Applications Larger Sizes : Available On Request

Special Features :- It is specially designed to reduce moisture and oil content from 2000 PPM to 100 PPM at a very low pressure drop.   Construction :- The outer casing is made of fabrication or casting to withstand high pressure. The elements are made of absorbent & coalescing media.   Application :- It is most suitable for installing in compressed air line for removal of moisture, oil, scale, and other particles (95% down to 3 micron).

The compressed air coming out from an After Cooler, contains large quantities of water vapour condensed as a result of cooling of the compressed air. If this is not removed, much of it will be carried to the distribution system and cause extensive damage to all the equipment and processes, which use the air.Apart from water vapour, there is also an appreciable quantity of oil vapour that is formed due to heat and pressure carried along with the air stream is also removed by the separator. Wet steam is steam containing a degree of water, and is one of the main concerns in any steam system. It can reduce plant productivity and product quality, and can cause damage to most items of plant and equipment. Whilst careful drainage and trapping can remove most of the water, it will not deal with the water droplets suspended in the steam. To remove these suspended water droplets, separators are installed in steam pipelines. The steam produced in a boiler designed to generate saturated steam is inherently wet. Although the dryness fraction will vary according to the type of boiler, most shell type steam boilers will produce steam with a dryness fraction of between 95 and 98%. The water content of the steam produced by the boiler is further increased if priming and carryover occur. There is always a certain degree of heat loss from the distribution pipe, which causes steam to condense. The condensed water molecules will eventually gravitate towards the bottom of the pipe forming a film of water. Steam flowing over this water can raise ripples that can build up into waves. The tips of the waves tend to break off, throwing droplets of condensate into the steam flow.

We supply MOISTURE SEPERATOR Compressed Air is vulnerable to Various types of contamination which greatly reduce its value as a power source and which can have a profound effect on the machinery that it operates. Moisture is most common contaminant present, and the one which probably causes the most damage. There is approximately abut 35gms of water in one cubic meter of atmospheric air. A cubic meter of air weighs approximately 1 kg (1000gms). This means 3.5% of air may be moisture, It is harmful in compressed air Pipelines. Over 80% of this nuisance. Comprises of particles less than 2 microns in size and these easily pass through a typical compressor intake filter. This moisture must be removed from the compressed air line at best it corrodes, erodes pipeline and equipment, damages coatings, contaminates lubricants, washes it from pneumatic loops etc. now 1 NM3 of air will hold only 35 gms of water at ambient temperature. The system will release the liquid water, oil etc. Beyond 35gms i.e. 245gms per IVF of air. The liquid will be in fog/aerosol form and be carried into the pipe work Down-stream. The wet air will generate large quantity of rust and scale. Hence moisture is the most un-welcome product in compressed air system.

We are successfully ranked amongst the topnotch entity offering a wide range industrial moisture separator. This separator is comprised of a variety of filters, pollution retention system, and high rate of cod. The provided separator removes 98.99% of salt from the water.

We manufacture a wide assortment of indoor air filtration systems and industrial air filtration systems like air moisture separator, steam moisture separator, industrial moisture separator, compressed air moisture separator etc., that are fabricated using high quality raw material and are used to for the filtration of air. Applicable in various industries

Description: IndoAnushka make Moisture separator with drain module is a value added solution for removal of moisture from the steam headers. Moisture separator with drain module consists of M.S. fabricated moisture separator with completely assembled drain assembly consisting of ball float steam trap, IndoAnushka make MAINTENO strainer with inbuilt blowdown valve and IndoAnushka make MULTIVIEW double window sight glass with deflector and 1 no. Isolating valve completely assembled with interconnecting piping and 1 no. Outlet nozzle as provision for bypass. Available Sizes: 15NB ONWARDS upto 300NB. Pipe Connections: ANSI 150, 300 & 600. BS-10 Table-H, J & K Limiting Conditions: For Moisture Seperator – Max. working pressure and temperature as per flange ratings. For Drain module – Max working pressure-13bars, Max working temp – 180 OC. Materials : Body & Baffles – M.S. Fabricated Trap – C.I with ss internals Strainer – CI with ss internals Multiview- M.S Fabricated Valves – CI