Epoxy Flooring Dealers in Faridabad

(18 products available)

All IndiaFaridabadPune Delhi Mumbai Bangalore Chennai Ahmedabad Hyderabad Kolkata Surat

Premium
Asian Paints Smartcare Apcoflor Lsc 3 N Epoxy Screed

105 / Kilogram

MOQ100 Kilogram
Packaging Size15 Kgs (base: 3.0 Kgs,Hardener: 1.5 Kgs,Aggregate: 10.5 Kgs)
Country of OriginIndia
Brand NameAsian Paints
ColourClear
AppearanceGlossy
Recommended DFT/ Coat2 - 3 mm
Theoretical Covering Capacity0.26 sq.mtr/ kg @ 2 mm DFT 0.17 sq.mtr/ kg @ 3 mm DFT
Consumption3.88 kg/ sq.mtr @ 2 mm DFT 5.82 kg/ sq.mtr @ 3 mm DFT
Drying TimeSurface Dry: 6 hours Hard Dry: 24 hours Full Cure: 7 days
Mixing Ratio (by weight)Base: Hardener: Aggregate 20 : 10 : 70
Pot life30 minutes
Overlay Interval (topcoat)Min. : 8 hours Max. : 48 hours, provided surface is clean and free from any contamination
Compressive Strength (ASTM C 579)41.0 MPa
Flexural Strength (ASTM C 580)10.0 MPa
Tensile Strength (ASTM C 307)8.0 MPa
Pull off Adhesion (ASTM D 4541)>1.5 MPa (Concrete Failure)
Shelf LifeAtleast 12 Months
Regulatory InformationFlash Point: Base - Not Less Than 24°c; Hardener - Not Less Than 24°c Voc: 75 Gm/ Ltr As

FEATURES\\\\n• High strength, heavy duty flooring with good impact resistance.\\\\n• Good flow and levelling properties making it easy to apply.\\\\n• Ideal underlayment for Apcoflor topcoats.\\\\n• Exhibits excellent bond with primed substrate and Apcoflor topcoats.\\\\n \\\\nThe data given is for guideline only. The physical values are subject to normal manufacturing tolerances, colour and testing variances. The coverage & consumption figures are theoretical and do not allow for any additional material required due to surface porosity, surface profile,variations in level or wastage etc.\\\\n \\\\nThe actual drying time/ overcoat interval may be shorter or longer, depending on film thickness, ventilation, humidity,\\\\ntemperature etc. The information provided above is at 30°C and 65% relative humidity.\\\\n \\\\nSUBSTRATE QUALITY\\\\n• Concrete substrates must be sound and of sufficient compressive strength (minimum 20 Mpa) with a minimum tensile strength of 1.5 Mpa.\\\\n• A sound, clean and dry substrate is absolutely essential for successful coating application and ensuring maximum bonding between the substrate and coating system.\\\\n• The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treat ments, etc. and have a moisture content less than 5% prior to application of the primer. Ensure that the substrate does not suffer from rising moisture and potential osmosis problems.\\\\nSURFACE PREPARATION\\\\nNew Concrete Floors:\\\\nShould be at least 28 days old or have a moisture content of less than 5% before proceeding with epoxy primer application. Laitance and deposits on new concrete floors are preferably removed by light grit/ shot blasting, mechanical scarifying or grinding to achieve an open textured surface.\\\\nOld Concrete Floors:\\\\n• Determine the general condition, soundness, presence of contaminants, presence of moisture vapour emissions and the best methods to prepare the surface to receive floor coating system. Mechanical surface profiling by grit or shot blasting, grinding or scarifying are the preferred floor preparation methods on old concrete floors.\\\\n• Hydrophobic contaminants can be identified by a simple water drop test. Other contaminants can be identified by pH.\\\\n• Remove localized weak or deteriorated materials from the surface. Remove bond-inhibiting materials such as oils, grease, wax, fatty acids, and other contaminants. This can be accomplished by the use of detergent scrub bing, low pressure water cleaning (less than 5000 psi), steam cleaning, or chemical cleaning. Acids and alkalis can be removed by neutralizing to form a water soluble salt and then high pressure water cleaning and mopping it off to dry state.\\\\n• In the areas where the contaminants cannot be removed, complete removal and replacement of the contami nated surface is typically considered.\\\\n• Surface defects such as voids, bug holes, excess porosity, and physical and chemical damage are usually filled or the installation of the floor coating system. Materials such as slurries, mortars, and polymer concrete are used to level, smooth and patch concrete surfaces. High spots must be removed by grinding.\\\\nFLOOR JOINTS\\\\n• All cracks and construction joints present, based on the depth of the crack, should be filled either with epoxy putty or mortar after primer application.\\\\n• The expansion joints should not be overcoated with the coating and to be addressed with suitable material.\\\\nPRIMING\\\\n• All surfaces to be primed with Apcoflor FP 110/ Apcoflor HFP 120 designed for maximum absorption and adhesion to concrete substrates. The primer should be applied immediately to the prepared substrate using stiff brushes and/or rollers. The primer should be well ‘scrubbed’ into the substrate to ensure full coverage, but care should be taken to avoid over application or ‘ponding’.\\\\n• Allow the primer to dry before proceeding to the next stage; do not proceed whilst the primer is ‘tacky’ as this will lead to unsightly marks in the finished surface.\\\\n• Porous substrates may require a second primer coat - when the first coat is directly absorbed into the substrate, but minimum over-coating times must still be observed.\\\\n• Freshly applied primer should be protected from damp, condensation and water for atleast 24 hours.\\\\nMIXING\\\\n• Apcoflor LSC 3 flooring is supplied in 3 pre-weighed packs (Base, Hardener and Aggregate) which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor.\\\\n• A suitable power driven mixer such as a bucket mixer is recommended for uniform mixing of the screed material. Stir the base and hardener separately. Blend the aggregates in the bag. Mix hardener gradually into the base under continuous stirring. Mix the aggregates into the mixed resin portion uniformly under continuous mechanical agitation. Mix well for 3-4 minutes till the components become homogenous. Apply after induction time and before expiry of pot life.\\\\nAPPLICATION\\\\n• The product may be applied by a serrated/ notch trowel to the required thickness. The entire mixed material should be poured onto the prepared and primed surface and spread slowly and evenly. To ensure proper levelling and appearance avoid overspreading. The laid material should be rolled firmly with a spike roller to ensure compactness and de-aeration of the film. Always wear spike shoes when rolling with spike roller. The rolling should be carried out using a ‘back and forth’ technique along the same path. An overlap of 50% with adjacent paths is recommended. Further light rolling may be required to remove surface imperfections, or for subsequent release of trapped air. This should be done prior to the setting of the product. To avoid roller marks prevent over rolling of the coating.\\\\n• The coverage & levelling would vary significantly based on the nature & levelling of the concrete surface.\\\\n• Freshly applied screed should be protected from damp, condensation and water for atleast 24 hours.\\\\n• At low temperatures, the chemical reactions are slowed down; this lengthens the pot life, open time & curing times. High temperatures speed up the chemical reactions thus the time frames mentioned above are shortened accordingly.\\\\n• After overnight curing of Apcoflor screed, light grinding on cured Apcoflor screed is essential to ensure proper adhesion in between topcoat and screed coat. Topcoat application to be carried out within 24 hours after lying of Apcoflor screed.\\\\n• Method statement will be provided separately.\\\\nAPPLICATION CONDITIONS\\\\n• Residual moisture content of the concrete substrate should not exceed 5%.\\\\n• No rising moisture & potential osmosis problems.\\\\n• Substrate temperature should be at least 3°C above dew point but not above 50°C.\\\\n• Recommended ambient temperature for application is between 10°C - 40°C.\\\\n• Relative Air Humidity (RH) to not exceed beyond 80%.\\\\n \\\\nCLEANING\\\\nAll tools and equipment can be cleaned with Thinner T 141 immediately after use.\\\\n \\\\nSAFETY INFORMATION\\\\n• As a general safety measure, inhalation of solvent vapours or paint mist and contact of liquid paint with skin & eyes should be avoided. Forced ventilation should be provided when applying paint in confined spaces or stagnant air. Even when ventilation is provided, respiratory, skin and eye protection is always recommended while spraying paint.\\\\n• Please refer our Material Safety Data Sheet prior to using the product.

...more
www

Excel Flooring & Paint Solutions

Sector 39, Faridabad

GST 1 yr
Glossy Polyurethane Floor Topping

Get Price Quote

MaterialPolyurethane
Finishing TypeGlossy
Water ResistanceYes
Service ModeOffline
Payment ModeOffline/Online
Service LocationClient Side

...more
V R TECHNOLOGY

Sector 21, Faridabad

10 yrs
Epoxy Resin Flooring

Get Price Quote

MOQ200 Litre
Number Of FlowerEpoxy Flooring
FeatureEpoxy Resistant, High Strength, Quality Tested
Floor UseFloor Use
Country of OriginIndia
Brand NameVimal Paints
Production Capacity1000 ltr per/day
Packaging Size20L

...more
M/s Vimal Paints

Dheeraj Nagar, Faridabad

GST 12 yrs 5.0 (1)
Epoxy Flooring

Get Price Quote

LifeLong Life
Color thicknessyour choice

With our experience of completing over one million Sq. Feet Epoxy Flooring during last 8-10 years all over the country, we are keen to take up most challenging projects and complete the same to customer satisfaction. We are one of the leading organizations engaged in industrial services related to Epoxy flooring and Epoxy coating, FRP coating , Effluent and water treatment and others having track record of undertaking and completing many similar projects to the satisfaction of our valued clients all over India. We have been providing these services for many years, to many organizations of repute all over India particularly in NCR, Maharashtra, Channai, Hyderabad, Uttarakhand, Himachal and other places with highly customized solutions to their requirement based on composition of floors, nature of surface undulations and traffic conditions. We are confident of satisfying you with our skilled manpower and advanced techniques. Our core competence is in Epoxy Installation techniques which determine aesthetics and longevity of Epoxy Flooring. We have been able to serve all our patrons in an efficient manner due to the support of world-class facilities as well as our dedication towards the clients. Sr. No A few of our major clinets--- App-Area covered-SFT 1 Panasonic JVC India Limited—NOIDA 40,000 2 Samsung India Electronics Limited 30,000 3 L& T Ltd---Faridabad and IMT Manesar-Gurgaon 18,000 4 Whirlpool of India –Faridabad,Pune and Pondicherry 60,000 5 Bright Autoplast -Faridabad,Sohna,Chennai & Pondicherry 80,000 5 Vikas Group( Sanden vikas, Sata Vikas,Ecocat,Ensa Vikas)-Faridabad 55000 6 Endurance Technologies ( Aurangabad , Pune, Pantnagar) 90,000 7 Dabur India---Pantnagar 18,000 8 Action construction equipments Faridabad 14000 9 Suzuki Motors-Gurgaon 15000 10 Kargigeya Plastics Group—Chennai 60,000 11 Epotome components-Ahmadnagar 30000 12 Aurangabad Motors Group-Aurangabad,Faridabad and Pune 40,000 13 DLF Utilities---Gurgaon 100,000

...more
Quantum Technologies

Sector 8, Faridabad

18 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Plastic Sheets, Micro Silica Powder, Industrial Boiler

Karanwal Infratech Materials Private Limited

Sector 28, Faridabad

15 yrs
Industrial Epoxy Flooring

Get Price Quote

Industrial Epoxy Flooring, Waterproofing Construction Chemical

G K ENTERPRISES

Sector 36, Faridabad

12 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Floor Hardne

INDIA TECHNOLOGY

Adarsh Nagar, Faridabad

13 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, ESD Flooring, PU Flooring, Parking Deck Floorin

P P FLOORING SOLUTION

Sector 87, Faridabad

GST 9 yrs
Industrial Epoxy Flooring

Get Price Quote

Industrial Epoxy Flooring, Epoxy Resin Hardeners, Epoxy Flooring Service

Epoxy India

Kheri Road, Faridabad

8 yrs
Epoxy Self Leveling Insulating Flooring

Get Price Quote

Epoxy Self Leveling Insulating Floorin

Gunwati Polymer Pvt. Ltd.

Sanjay Colony, Faridabad

9 yrs
Epoxy Flooring

Get Price Quote

We are offering epoxy flooring. You can now provide clean, hygienic, and dust proof surface to the floor by using self levelling epoxy flooring that is a 3 component self leveling epoxy having thickness from 2mm to 3mm. It is extensively used in pharmaceutical units, operation theatres, food factories, and also in tv picture tube manufacturing units and so forth due to its outstanding features. It is resistant to majority of alkalies and acids, anti bacterial as well as antifungal. Features: •impeccable quality •wide ranging applications
...more

Fibrex Construction Chemicals Pvt Ltd

Dlf Industrial Area, Faridabad

12 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Epoxy Primer, Waterproofing Service, Coating Service

West Coast Coatings

Faridabad

1 yr
Epoxy

Get Price Quote

Epoxy, Epoxy Flooring, Epoxy Painting, Special Coatin

Techman Consultancy

Gurgaon Mehrauli, Faridabad

14 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Floor Hardner, Pergo Laminated Wooden Tile

Eminent Solution

Sector 37, Faridabad

13 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Wall Coatin

sai enterprises

Ballabhgarh, Faridabad

11 yrs
Epoxy

Get Price Quote

Epoxy, Rubber Roller, Ducting, Industrial Liners, Rubber, Rubber Sheet

Makharia Rubber & Fibre Products

NIT, Faridabad

14 yrs
Epoxy Flooring

Get Price Quote

Epoxy Flooring, Epoxy Floor Coating

Om Sai Enterprises

Ballabhgarh, Faridabad

12 yrs
Epoxy Flooring Screeding Services

Get Price Quote

Epoxy Flooring Screeding Services, Roof Insulation Service

Hi Tech Property Management & Services

Mathura Road, Faridabad

9 yrs