Air Separator Dealers

‘ORIENTAL’ separators are manufactured using the best quality glass fiber media as per or superior to the specification of the OEMs. ‘ORIENTAL’ separators are constructed with the amalgamation of multilayered extremely efficient glass fiber, filter paper, glass woven sheet and filter media. It minimizes the oil flow and oil losses in the compression system and makes the compressor run smoothly.

In order to increase the capacity of a separator and keep the dimension same, Flocon provides one alternative is to increase the separation area. This can be achieved by the pleating the separation media. The more media is used, the higher capacity is reached. Our management is amongst the reputed Air Oil Separator manufacturer and supplier in India that has been served a huge clientele with perfectly finished products. Our bussiness group is recognized the Air Oil Separator manufacturer and supplier that is engaged in providing a huge variety of products at market leading prices.     With immense of expertise, our huge workforce is capable of producing a gamut of Pleated Air Oil Separator. As a leading manufacturers and exporters of Pleated Air Oil Separator, we offer you an exclusive range of products at very lowest prices. These are being fabricated by our well qualified team of experts in compliance of quality standards. We have got a lot of appreciation because of its high quality products that are being made up with the perfection to finish. It can also be customized as per the stated specification of our valued customers. We have an expertise in manufacturing an assortment of Pleated Air Oil Separator which is highly demanded by the diverse industries at the international level.

Air separation column (cold box) consists of outer steel casing, Main heat exchanger, liquifier, Bottom column, Top column, Condensor, Sub-cooler, Liquid oxygen & nitrogen filter. Cooling pipe line, insulationmaterial, Digital electronic temperature indicator & scanner, PT 100 sensor, DP gauge monometer, Expansion valve with longstemp type with pointer & index & wheel -1 set. Features of Air Separation Units • Latest Technology • Compact Design • Easy To Operate. • Practically Zero Maintenance. • Low Power Consumption • Air Separation Liquid Technology. • Skid Mounted. • High Purity of Oxygen >99.6%, Suitable For Medical/Hospital and Industrial Uses. • Single Electric Panel. • Cylinder Filling Station (Optional). Being a reputed and known air separation column (cold box) manufacturer in India, we use optimum grade war materials and incorporate the latest technology to ensure durability, reliability and ease of use. In addition, we keep the requirements of esteemed clients from numerous industries in mind while manufacturing the products. To get more details, contact us.

We are counted amidst the well-known names involved in providing quality products from jamkhandi(India). In order to deliver quality content, our entire production process is commenced under the strict eyes of quality examiners.

Material of Construction : Carbon Steel – Flanged to Class 150/PN16/ PN25 All steel body Stainless steel strainer . Advantages : Elimination of air from closed circulation system. Tangential style Low velocity vortex Avoid inefficient pump operation. Low pressure drop across the separators. . Benefits : Recover air perfectly Optimum pump operation Prevent pump cavitation. “Precision” tangential air separators are manufactured in state of the art modern facility with automatic machines. . Principle : Precision Tangential air separators removes air from the system through centrifugal action, with a combination of centrifugal force and with reduction of velocity. This makes the air, force water towards the outlet connection, where the separated air moves to the low velocity center. Air is removed from the system through air vent. Operating Conditions : Standard working pressure : 10 bar Standard Working Temperature – 177°C Can supply for pressure up to 30 bar

For quite a few number of years now, we have been supplying the Cross Flow Separator that we manufacture in our very own factories under the guidance of our knowledgeable experts. This separator is made of top notch materials sourced from authentic vendors that account for the premium quality and performance it houses. We deal in bulk and medium sized orders primarily. The rates are affordable and delivery is punctual.   Details : In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter. The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid. Imagine a rectangular tank with a surface A containing a liquid to a height H (see figure 1). Flow through the tank is homogeneous and the flow rate = Q The settling or rising velocity of a particle with diameter d is governed by Stoke's Law It follows that the tank surface A is inversely proportional to the square of diameter d of the smallest particle which will completely separate. An increase in the efficiency of a separator can, as a result, only be achieved by a considerable increase in the surface A, which leads to the installation of large tanks with large surface area A. The effectiveness of such large tanks is limited due to factors like : Turbulence and short-circuit currents. Variation in ambient temperature. Temperature gradients in the liquid. Surface wind load.   In the modern TPI System, the separating surface area is increased vertically by the addition of a number of parallel plates mounted at an inclination. This not only affords a dramatic space saving but also facilitates very small separating diameter. The K-pack TPI consists of a plate pack constructed of closely spaced corrugated plates inclined at a 45° angle or more, depending on the application. Waste water flows through these plated either parallel to the corrugations in "Counter-current Flow" or at right angles to the corrugations in "Cross Flow". Under laminar flow conditions, the short distance between the inclined plates is now the only distance over which the pollutants have to rise or sink before they are intercepted and separated from the mother fluid. Application : Mineral oil refineries, oil extraction, offshore platforms Tank storage farms Ballast water treatment Petrochemicals Galvanizing metal; mining industry Edible oil refining Foodstuffs industry Paper & pulp industry   The Cross flow separator system permits simultaneous separation of floating and settling materials like oils, fibres, sand etc.. But are also individually applicable as oil and solids separators. The raw water containing oil and/or suspended solids passes in horizontal direction between the closely spaced plates in the plate pack. Completely laminar flow conditions are established while the water flows across the plate pack from the inlet to the outlet side. Laminar and stable flow conditions are essential conditions for the effective gravity separation of the water, oil and/or the suspended contaminants.   Oil separation : In the course of passing through the plate pack from inlet to outlet, the oil floats upwards info the tops of the corrugations and rises up the incline of the plate to the surface of the separator, where it is removed by a skimmer. Solids Separation : The solids move towards the Bottoms of the corrugations and slide down the incline of ' the plate. From there the separated solids are collected in the sludge compartment of the separator to be partially dewatered and transported by a shaft less spiral conveyor and intermittently discharged through a blow-off valve (optional). Settled sludge cannot decontaminate the treated water. Oil and solids move in separate directions, but both perpendiculars to the flow of water, eliminating particle re-entrainment completely. All K-Pack separators are custom built with respect to the number of plates in the pack, the length of the plates, the distance between the plates and the plate incline. The number and the length of plates is determined as a function of the raw water flow rate to be processed in the separator. The distance between the plates is depending upon the concentration of solids / sludge in the raw water. The incline of the plates is set between 45 and 60 degrees depending upon the general nature of the Oil and/or sludge, (density, viscosity, concentration). The systems are fabricated in mild steel and other materials are available on request. The oil separators are standard with oil and skimpipe and 45 degree shaped compartment. The solids separators are optionally with a shaftless conveyor in the sludge compartment. In the corrugation tops a very high oil concentration is established. This is the ideal condition for oil coalescing to take place (formation of large oil droplets out of many small oil droplets). In the corrugation bottoms a high sludge concentration is established. This is the ideal condition for particle agglomeration to take place (formation of heavy particles from small and relatively light particles) Applications Mineral oil industry Edible oil industry Metal industry Ceramic industry Galvanic industry Mines Sand separation after washing of contaminated soil Food industry

We offer various filters such as Air Filter, Oil Filter, Fuel Filter, Lube Filter, Coolant Filter, Hydraulic Filter, High Pressure Filter, Hepa Filter, Air oil Separator, Filter Cart, Cabin Filter, Crank Case Ventilation, Steering Filter etc..  We are also authorised distributors for Mann+Hummel-Germany and Donaldson-USA.