Changeover Switches Dealers in Mumbai

The Series BYDS Bypass Damper Switch is designed to control motorized bypass dampers. As individual zone dampers open and close, the system static pressure will rise and fall. In order to maintain proper airflow and static pressure through the HVAC system, a bypass system incorporating a floating type motorized damper and a static pressure control should be incorporated. A typical onoff pressure switch cannot operate in this application due to the high cycle rate that would result, eventually causing contact burnout. The BYDS static pressure control is equipped with a solid-state switching and timing circuit to enhance operation and improve long-term reliability in this demanding application. CONTROL OPERATION The BYDS Bypass Damper Switch is designed for use with a three wire floating point damper actuator used to control the static pressure on zone control systems requiring motorized bypass dampers. A bypass damper, bypasses air from the discharge air side of the HVAC unit back in the return air side. The air flow is modulated in order to maintain a constant static pressure in the system as individual zone dampers open and close. The static pressure control is equipped with solid-state switching which dramatically increases the life of the control. On an increase in static pressure the BYDS will send 24 volts out and start the actuator to drive open. When the static pressure reaches set-point the actuator will stop. After a ten second delay the actuator will start to drive the damper closed if there has not been an increase in static pressure. A green LED indicates when the damper is in the open position or being driven open. A 24 VAC transformer is required to power the BYDS control and damper actuator. The unit includes tubing and two static pressure probes.

Changeover switches provide uninterrupted alternate supply to essential equipment in the event of failure of normal supply. They are designed to feed the load from one of the two incoming sources, depending upon supply status and mode selected. We offer Auto as well as Manual Changeover Switches.

Product Features :- Manual operation of motorised changeover switch is also feasible through the manual override feature. The Control supply of motorised changeover will automatically cut off during insertion of manual handle. Motorised Changeover comes with a Auto/Manual selector switch. It enables the control supply to motorised changeover switch. Provision for padlocking in OFF position up to three padlocks is available. Padlocking is possible in both auto and manual mode.   Overall dimensions of motorised and manual changeover switches remain the same, which makes upgradation easy. Complete touch proof design, with help of terminal shroud, source separator & inter-phase barriers. Staggered terminals provide clear access to all terminals from the front, ensuring ease of termination.

Interpact INSINV - Source changeover switches 40 A to 2500 A. Source changeover switch produced around 2 Interpact INSINV. Manual changeover switches by interlocking of operating mechanisms via rotary handles or with captive keys. Possible complete source changeover assembly for Interpact INS250-100 A to INS630A. Wide range of auxiliaries and accessories common to the Interpact range.

Product Features :- Complete touch proof design, with help of terminal shroud, source separator and inter-phase barriers Staggered terminals provide clear access to all terminals from the front, ensuring ease of termination Patented dual dead center mechanism enables the user to toggle between central or side positions for operating handle. This can be easily converted on site as required C-Line Manual Changeover Switch   Multi featured operating handle :- Unique flip-able handle for rating 400 A and above which enables the user to operate the switch with two hands Provision for padlocking in OFF position with three padlocks Defeat feature in both ON states and auto restoration of panel door IP54 with extended type operating handle

Changeover Switches, also called Double Throw Switches, are available with OFF and without OFF. These are used to operate two different circuits, with different number of inputs and outputs. Changeover Switches without jumpers (potential free contacts) are used to connect two different circuits from two different sources, with two different operating voltages or any other incompatible lines. All contacts by default are "Break Before Make" (BBM) type to avoid overlapping of different circuits while overlapping changeover contacts. "Make Before Break" (MBB) type are offered against specific requirements. Applications: Power Supply to Generator Changeover, AutoManual changeover, StandbyRemote Changeover and other special application circuits. Mainly used in Distribution Panels, UPS etc.

. It provides saf changeover, source inversion or switching on load between two low voltage power circuits as well as their safety isolation.The pad lockable handle is to be mounted, on the panel door and lockable in ONOFF position. The external front operation ensures that the door is locked in ON position. Bridging Bars mounted on all ratings as standard.

Motorised changeover switch from 125 to 1600 A The SOCOMEC Motorized Changeover Switch is a motor operated 4 Pole changeover switch. It provides safe changeover giving two stable position I & II and help in changeover from one supply source to another remotely. In case of control supply failure, emergency handle arrangement is provided for manual operation of switch in “OFF” position or selecting the supply.

We are prominent Manufacturers and Suppliers of world class Electrical devices. The variety of Electrical Components offered by us comprises of Electrical Changeover Switches and Kit Kat Fuses. Our Company has marked its excellence in manufacturing Kit Kat Fuses made from superior quality raw material and Change Over Switches that mainly includes sheet metal double pole switch and four pole switch that can be used in various applications. These Electrical Components are widely acknowledged for their reliability and durability. We use the best quality Brass, Phosphorus Bronze Components and ETP Copper Contacts heavily plated with silver for improving their conductivity. The company is moving towards the advancement, making an inerasable mark in the industry by virtue of its Electrical Components. In addition to this, our Quality Work Culture and Commitment are some of the key factors that build up the base of our company.

Owing to our excellent connectivity, trusted shipping facilities, we smoothly deliver the product basket to the clientele. Having captured all markets of (India), our company has emerged as an acknowledged provider of this product range.  Main Function : Monitoring handrail direction Monitoring staffs entire handrail Record data to safety circle

Bypass Switches, Earth Leakage Circuit Breaker, Em Fis Meters, Switchgea

We are offering change over switch and door bells.

Automatic Switches, Auto Component, Hydraulic Component, Pump Componen

Changeover Switches, Ceiling Fan, Fancy Ligh

Changeover Switches, Low Voltage Switch Gears, Industrial Switch Gear

Automatic Rotary Switch, Auto Phase Change

Change Over Switches, Switchgear Components, Rotary Switch, Cam Switc

Change Over Switches, AC Box, Power Distribution Boards, Isolato