Limit Controller Dealers in Andheri East, Mumbai (19 products available)

• Type: Pid Controllers
• Certification: ISO 9001:2008
• Voltage: 110V, 220V
• Condition: New Used
• Display Type: Analog
• Feature: Durable
• Warranty: 1Years

We are the main supplier of this product.

• Brand Name: TAGLab

We are offering proportional control system,. Proportional action on different actuated error signals generated externally control of proportional rate & study of its effect on the controlled signal electronic simulation.

• Type: Automatic
• Brand Name: Radix
• Feature: Full featured
• Controller Type: PID
• Usage:  application requiring precision,where there is no margin
• Digit Display Size: Dual Display
• Analog Output: Upto 2
• Communication Interface: RS485 / MODBUS RTU
• Size: 96*96*100
• Relay Output: Maximum 4
• No. Of Input: 2*Universal input
• Digital input: No
• Display digits: 4+4+3
• Transmitter supply: Yes

pH Controller, Level adjuster, battery indicator, Bin Level Indicators

stepper motion controller, bipolar stepper driver, electronic spare part

• Features: Highly demanded, Supreme strength, Easy installation

The PID Stress Relief Programmer Controller is used for controlling the rate of heating, soaking and rate of cooling during stress relieving operation. It can be used in conjunction with the power source unit or other contactorised units. Features Control Types PID with Pre-tune and RaPID fuzzy logic, or Manual Tuning. Heat or Heat / Cool, applications Auto/Manual Selectable from front panel, with bumpless transfer Output Configuration Up to 3 total. Max 2 for control (Heat & Cool), max 2 for Alarms, max 1 for retransmit PV or SP Alarm 1 & 2 Types Process high, process low, setpoint deviation and band Human Interface 4 buttons, 10mm & 8mm high LED’s, plus run-hold, tune, event & profile / control status LED’s PC Configuration Off - line configuration & profile editing via config socket (comms option not required)     Profiles Number of Programs 4, each with 16 free-form segments (Ramp/Dwell/End). Max segment length 99 hours 59 minutes Delayed Start Max 99 hours 59mins delay from initiation to program start Guaranteed Soak Holds program if PV is outside of specified hold band during dwell segments. Program Cycles 1 to 9999 or infinite (continuously re-starts program at end) Ramp Rate Definition Either ramp rate, or time to final setpoint Power Loss Recovery Hot (continue profile from point of power fail) or Cold (end profile and return to controller mode)     Input Thermocouple J, K, R, S, T, B, L, & N. RTD 3 Wire PT100, 50W per lead maximum (balanced) DC Linear 0-20/4-20mA, 0-50/10-50mV, 0-5/1-5/0-10/2-10V. Scaleable -1999 to 9999, dec point available Impedance >100MΩ for Thermocouple and mV ranges, 47KW for V ranges and 4.7W for mA ranges Accuracy +/- 0.25% of input span +/- 1 LSD (T/C CJC better than 0.7°C) Sampling 4 per second, 14 bit resolution approximately Sensor Break Detection 500,000 operations DC for SSR Drive capability >4.2V DC in 1KΩ (10V 500Ω version available) DC Control/Retransmit 0-20/4-20mA into 500Ω max, 0-10/0-5V into 500Ω min. Control OP +/- 0.5%, Retransmit +/- 0.25% Solid State (Triac) 0.01 to 1 Amp AC 20 to 280V, 47 to 63Hz Remote Run-Hold Volt free or TTL input (Hold = -0.6 to 0.8V or contact open, Run = 2 to 24V or contact close) Communications 2 Wire RS485, 1200 to 9600 Baud, Modbus     Operating & Environmental Temperature & RH 0 to 55°C (-20 to 80°C storage), 20% to 95%RH non-condensing Power Supply 90 to 264V 50/60Hz (optional 20 to 55V AC/22 to 65V DC), approx 4 Watts Front Panel Protection IEC IP66 (Behind panel protection is IP20) Approvals and Certification CE, UL & Ulc  

Choose from cost-effective or full-featured Radix PID Controllers that accept inputs from RTD sensors, thermocouples as well as linear inputs such as 4 - 20 mA, 0 - 20 mA, 0 - 50 mV and the like. All the PID controllers mentioned has the autotuning function. Autotuning function tunes the PID controller to produce accurate control, it takes the factors like external periodic variation in temperature, environmental temperature or surrounding temperature etc into consideration while tuning itself. These factors may affect the controlling function and are essential for accuracy. Large LED displays and LED lights on the controller indicate process variables and relay, communication status and are easily visible to operators from a distance. Operators can easily program setpoints, alarms, control outputs on the controller via membrane keys on the front of the unit to trigger heating, cooling, high-low alarms. Our PID Controllers broadcast signal isolated outputs to protect all downstream machines and devices (such as programmable logic controllers)  from damaging fluctuations in the input signal. Many of these products have a flameproof version as well, which can be found here.  

proportional integral derivative controller, Industrial Gauges

Maximum Demand Meter, Analogue Panel Voltmeters, Dc Energy Meter

motion controller, Ac Gear Motor, Battery Charger, Digital Inverter

VCB Panel, Electrical Distribution Board, ac controllers, PCC Panels

humidity controllers, Temperature Instruments, Thermometer, Gas Analyzer

Digital SCR Proportional Controller, Soft Starter, interface modules

controllers, LCD, touch screens, display inverters, ruggedized diplays

controllers, ac servo drive, dc servo drive, Industrial Motors

Vacuum Controllers, Dc Brush Drives, Rotery Piston Pumps

Speed Controller