Test Bench Dealers

3 relays can be at a time checked for continuity and reliability to heat. (The number of relays to be tested can be customized). The panel can work in Manual mode: Here all the settings for current and primary voltage are done manually. The test would only start when the Heating Test On, dual push button is pushed ON. Timer mode: Here too all the settings for current and primary voltage are to be done manually. Here the timer is set, to enter the time, for which the current is to be passed and the test would only start when the dual start push button is pressed. PC mode, where it performs all the operations automatically using TESTWARE, without manually entering the settings again and again. If the particular station is to be left empty, then it can be bypassed using a toggle switch present on the panel. PC USB port is used for PC interface.

The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy.  

Structure and Features:︰ The water meter test bench is made up the platform, clamps, back and front pipe, flow counter group, standard measuring instrument and the outlet valve. When the inlet is connected with the stable water source, the water will get to the standard measuring instrument through the straight pipe. Compare the value of the checked water meter with that of the standard measuring instrument, the valve error that the water meter reads will be acquired. Technical Parameters:︰1. Checking gadget precision: ± 0.2%；2. Water meter diameter : φ15、φ20、φ25、φ40、φ50；3. Testable water meter indicators: For overall performance test (for the production)4. Instant flow indication: glass rotor flow counter, the actual accuracy should be no lower than 2.5%;5. Measuring instrument volume:15-25mm, (10L+10L) 20L, (50L+50L) 100L;15-50mm, (10L+10L) 20L, (100L+200L) 300L;6. Working Pressure: 0.25-0.4MPa;7. Clamp flexibility: 15-25mm checking gadget: 500mm, 15-50mm checking gadget: 60mm

Test Benches are widely used for various types of Voltage testing, Current testing. Our test benceh contains multifuntion meter , variable AC source, Variable DC source.  

The performance of a Diesel Engine depends upon its injection pump. Diesel fuel pump test benches records and sets the performance of the fuel injection pump to the maximum accuracy.

We are concerned with the manufacture and supply of a massive compilation of Alternator Tester that is handed over in safe packaging. Used for car battery and charging testing, the proffered compilation comes with an efficient timer for auto cutoff load. Set up with battery status indicator and heavy-duty battery clips, these durable testers are massively demanded for their reliable performance. Features: Easy to operate Requires less maintenance Consistent performance Specification: Size: 110x280x60 mm For Car Battery & Charging Testing 0 - 20 V Operates on 9V Battery Low Battery Indication Size: 70x140x20 mm

The Main purpose of this panel is to Test Instrument like single phase three phase motor, thyristorstransformers, various parameters like current, voltage, resistances etc.Acting as a 24 Vdc power supply, DOL(direct online starter) starter, star delta starter, Radical calibrator, multimeter, variac, 110V DC supply,  etcC To Test 3 phase and single phase motor in DOL and Star Delta mode Soldiering and Desoldering 3 phase and single phase variac to vary voltage for testing of thyristors and transformers. Digital Multimeter Source Meter 24V dc power supply

The orifice assembly or the flow control element, valve, is calibrated under fluid mechanics standards of ISO 5167 and IEC 60534 standards. The process and the procedure of the measuring flow calibration of the device and the design is as per the international standards applicable for volumetric and gravimetric conditions. The flow calibration bench for upto 12” size, is applicable for pressure 2 rating upto 3 kg cm g and for all ambient conditions. The testing media is water. The calibration unit is under free length or straight length as per the ISO standards for mounting in such conditions applicable for orifice assemblies with water as media and with calculated beta value to decide the free length for calibration of sensors. For valves, the condition is kept at ambient conditions with water and based on IEC 60534 standard the flow coefficient value of the valve is matched with desired flow rate applicable under differential pressure conditions, under applicable and available free or straight lengths. The bench gets the water from an underground tank with an overall capacity of m3 which is having a magnetic level gauge mounted to check the level of water. The level in turn helps to clear the pressure applicable under the centrifugal pump which is mounted to the side to generate the desired and the requisite pressure for the flow assembly, either valve or orifice.

We are offering vibration test bench. multi test bench comprises of the following high pressure (10 to 4000) bar pressure cyclic test ( 0-400)bar vibration test -motorised (23-47) hz static test (gas) (0-150 )bar vacuum test (0-760)mmhg thermal test (0-600) deg c pull out (tensile) (0-4 ) ton rotary flex flexure fatigue.

hydraulic hand pump, test hoses and adapters, and protective hard case.Combine with any Fluke-700G Series Gauge, 1,000 psi range or greater, to make a complete pressure testing kit, Generates pressure up to 10,000 psi range or greater, to make a complete pressure testing kit,Includes 700HTH-1 hose kit and adapters for connecting to the pressure device to be tested.Hard case protects pump and gauge and allows gauge to remain connected to the pump.

Surface table and centre heads are made from closed grained iron castings, seasoned, stress releaved and finished on the working face and reference side edge of the table by hand scrapping to meet with the required accuracy's as per ISI Standards. The centre stock spindle bearings are smooth lapped to ensure accuracy of the spindle height and relationship to reference side edge. The centres are hardened high carbon steel accurately ground on the diameter and conical point. One centre is spring loaded to accommodate small variations in component length. Tee slot at 450 angle on the surface table and teebolt through hole at the base of the centre stocks to ensure firm engagement with the reference side edge of the table. Each centre stock can be locked in any position along the tee slot by means of knurled hand knobs.

Bharat Bijlee offers a complete solution for Test benches. The wide range of Automation products BBL offered are VFD’s (F5) up to 900Kw.Active front end (R6) up to 800 Kw, AC Induction motors, AC Servo motors, AC Asynchronous Servo motors, PLC’s for following test bench applications.An '''engine test stand''' is a facility used to develop, characterize and test engines. The facility, often offered as a product to automotive OEM’s, allows engine operation in different operating regimes and offers measurement of several physical variables associated with the engine operation.

Manufacture and Supply: Test Benches for Avionic Components. Test Benches for Electrical Components. Static Frequency Converters. Aircraft Battery Charger. Capacity Testing Unit.

Test Bench for Burner, Coal / briquette fired thermic fluid heate

Transformer Test Bench, Diagnostic Insulation Tester, Micro Ohm Mete

Calibration Test Bench, Woltman Type Bulk Water Meter

Alternator Test Bench, Water Level Controller, Temperature Monitoring Displa

Vertical Bench Centres, Angle Plates, Cast Iron Surface Plates, Ejector Pi

Bench Centres, Sine Centres, Industrial Tool, Cast Iron Surface Plat

High Voltage Testers, PLC Control Panels, Thyristorised Power Controller

Motor Testing Bench, Process Equipment Control with Remote IO'

CT PT Test Benc

Auto Electrical Test Bench 1 Phase, Battery Tester BAT13

Power Test Benches, Grid Paralleling Panel, Rotary Converte