PIR Sensor Dealers

The Honeywell IS2535 is a passive infrared motion detector that is may be used with or without pets. This PIR offers three selectable sensitivity settings, no pets, pets up to 40 lbs and pets up to 80lbs. Small pets, big pets or no pets, the IS2535 is a good fit for just about any application.

We at, websecsystems india are engaged in manufacturing and exporting a wide range of pir motion sensor for light (hc-7e). The compact design which enables to fix it conveniently in the car parking, drive ways and stair ways. These are manufacture by using excellent quality materials that are in the strict adherence with global standards. It works automatically with adjustment facilities. features: minimum electric consumption designed with weatherproof - ip44 automatic operating technology contemporary design.

We are offering a wide range of Pir Motion Detector. Specification : voltage – 5v-20v power consumption : 65ma ttl output : 3.3v delay time : adjustable (0.2->5min) lock time: 0.2 sec trigger methods : l-disable repeat trigger, h enable repeat trigger sensing range : less than 120 degree within 7 meter temperature – 15~+70 dimension : 32*24mm, distance between screw 28mm, m2 lens dimension in diameter : 23mm application : automatically sensing light for floor, bathroom, basement, porch, warehouse, garage etc, ventilator, alarm etc.

Ceiling Mount PIR 360 Degree Sensing Detection Range : 4.5Mtr. Dai at 3 Mtr. Height , Output Load up to 400 Watt , Suitable for Offices , Wash rooms, Pantry, Conf. Room , Stores , etc

• Stand alone 220V AC operation Room • Can switch light load of up to 300 Watts • Detection Range 3m radius at 10ft height • Lux Level Control - Time control • Re-trigger Function • Offices Conference • Toilets • Pantry • Stores Stairways • Lifts Lift Lobby • Dining Area Canteen • Basement Covered Parking Area • Locker Safe Room in banks Vaults • ATMs - Colleges Schools Institutes • Multi- Apartment Complexes 1. Rated Voltage: 230V AC 50Hz 2. Load Wattage: Max.1500W incandescent bulb or Max. 300W fluorescent lamp 3. Detection Area: Max. 5 Meters in radius 4. Detection Angle : 360° around 5. Time –delay : From 10 ± 5 seconds to 4 ± 1 minutes adjustable

DUAL ELEMENT PYROELECTRIC SENSOR DIGITAL SIGNAL PROCESSING (DSP) DETECTION RANGE UP TO 12M DETECTION ANGLE UP TO 110° SELECTABLE ZONE NUMBER JUMPERS SELECTABLE ADDRESS JUMPERS ABS HOUSING

These sensors are of three types :            Ceiling Flush Mount/ Ceiling surface mount Wall mount Indoor / Outdoor sensor. 

Motion Sensor for Factory Warehouse and Godown. IS 345 Mx Highbay [High ceiling mount PIR motion sensor] Type : - 180° PIR Motion Sensor Ceiling Mounting Height : - 12 meters Application : - Factory Warehouse and Godown Technology : - Ceiling mount Passive Infrared PIR motion sensor Reach : - 30 meters x 4 meters Time Setting : - 5 Sec - 15 Minutes Lux setting facility : - 2-2000 Lux Load switching : - 1000 W uncorrected inductive loads like fluorescent lamps/tubes with electronic ballasts - 230V AC 50 Hz. http://www.occupancysensor-motionsensorlights.com/warehouse.php

We are offering pir sensor for welcome bell high quality ... Branded products only call us on +91-999-663-5607 +91-941-613-5607 easy installation no expert required high quality & reliable do not fix this sensor near any heating materials

Features: 360 Degree-Ceiling mount,micro motion detectable. Photo sensor inside for smart control Run-on time adjustable Ambient lux, setting adjustable 2000 W /625 W loading Can Support IR remote Control also for On/ Off / Auto Control Detection range: 6m for micro motion @2.5height and 12m for walk across motion@ 5 height Warm up time: Approximately 1minute Output: Relay Size: 54(H)x114.5(D) mm With IR Remote Weight:160gms

A passive infrared sensor (PIR sensor) is an electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors. PIR sensor detects the infrared light radiated by a warm object. It consists of pyro electric sensors which introduce changes in their temperature (due to incident infrared radiation) into electric signal. When infrared light strikes a crystal, it generates an electrical charge. It will detect the motion via positive and negative differential changes in the both halves of the output. It won’t detect decaying light changes(slow moving light waves). There is no need of calibration for daylight.Most PIR sensors have a 3-pin connection at the side or bottom. One pin will be ground, another will be signal and the last pin will be power. Power is usually up to 5V.   Applications:- Automatic Door Opening System Security Alarm System.