Electronics Feather Touch Keyboard ,
Anatomical Programs Radiography (APR)
Auto As Well As manual Mode Selection.
Independent KVP . MAS and MA Display .
Various Voltage And Timer Setting Option.
Convenient Auto Programmed Helps Doctor For Better Image Quality.
Auto brightness control (Only in C-ARM X-ray Controller
Specifications
POWER SUPPLY
AC 230V , 50/60 Hz . 1A
INPUTS
6 Digital Inputs
ANALOG INPUT
Camera Signal
OUTPUT
13 Relay Output
OPERATION MODES
Radiography, Fluoroscopy
ALARMS
X-Ray ON Alarm For Safety.
Electronics Feather Touch Keyboard ,
Anatomical Programs Radiography (APR)
Auto As Well As manual Mode Selection.
Independent KVP . MAS and MA Display .
Various Voltage And Timer Setting Option.
Convenient Auto Programmed Helps Doctor For Better Image Quality.
Auto brightness control (Only in C-ARM X-ray Controller
Specifications
POWER SUPPLY
AC 230V , 50/60 Hz . 1A
INPUTS
6 Digital Inputs
ANALOG INPUT
Camera Signal
OUTPUT
13 Relay Output
OPERATION MODES
Radiography, Fluoroscopy
ALARMS
X-Ray ON Alarm For Safety.
POWER SUPPLYi) AC 230V, 50/60 Hz, 5A.
ii) DC 24V, 5A.
DIGITAL INPUT
6 nos. Inputs
ANALOG INPUT Strain gauge type loadcell
DIGITAL OUTPUT
i) 6 nos. Outputs [3A Load Tip facility.]
ii) 8 / 16 Bit Output For power / Vibrator controller.
Operator Interface Provided For Different Settings in 4- recipes (Such As Bulk-Dribble-Target Weights, Calibration Etc.) And Messages and weight Display At Run Time.
Microprocessor base Controller Specially Designed For Packaging [Granular Product] Machine. [Weighing Capacity 1gm To 100Kg]
PC – 903 Designed For Pressure Controlled, Time Cycled, and Continues Flow Respirator that is intended For Neonatal & Pediatric Use. Seven Different Modes of Ventilation Enhance User’s Efficiency matching The Varied Patient Condition’s.
Special Function Provision Of Bias Flow – Neonatal And Pediatric. SIMV Plus Pressure Support CPAP Plus Pressure Support Inbuilt Humidifier With Temperature Control. Low Consumption Of Gases And Electricity Facility of auto mode
PC – 903 Designed For Pressure Controlled, Time Cycled, and Continues Flow Respirator that is intended For Neonatal & Pediatric Use. Seven Different Modes of Ventilation Enhance User’s Efficiency matching The Varied Patient Condition’s.
Special Function Provision Of Bias Flow – Neonatal And Pediatric. SIMV Plus Pressure Support CPAP Plus Pressure Support Inbuilt Humidifier With Temperature Control. Low Consumption Of Gases And Electricity Facility of auto mode
Microprocessor based Timer used to set ON time for Phototherapy Unit.
Indication of Tube usage hours at power ON.
Phototherapy time can set from 30min to 24 Hrs. in 10 min increments.
Feed alarm can be set 30min to 3 Hrs. in 10 min increments.
Auto cut off once set time over. Audiovisual indication provided with Auto mute facility.
Audiovisual indication provided to change Phototherapy tube after permitted hrs. Auto mute facility.
Alarm provided for feed, change tubes Dose with auto mute facility
Microprocessor based Timer used to set ON time for Phototherapy Unit.
Indication of Tube usage hours at power ON.
Phototherapy time can set from 30min to 24 Hrs. in 10 min increments.
Feed alarm can be set 30min to 3 Hrs. in 10 min increments.
Auto cut off once set time over. Audiovisual indication provided with Auto mute facility.
Audiovisual indication provided to change Phototherapy tube after permitted hrs. Auto mute facility.
Alarm provided for feed, change tubes Dose with auto mute facility
Fluid Filling Controller Is Used For Filling Predefined Quantity Of Any Type Fluid Of Liquid. Specially Used In Industries.
Features
Required Quantity Liquid Can Be Set.
10 Programs of Different settings Can Be Saved.
Power Off Memory Retention of Flow meter Counts.
User Friendly Indication.
Program Lock .
Alarm Output on ERROR In Cycle.
Display of total Cycle counts
Fluid Filling Controller Is Used For Filling Predefined Quantity Of Any Type Fluid Of Liquid. Specially Used In Industries.
Features
Required Quantity Liquid Can Be Set.
10 Programs of Different settings Can Be Saved.
Power Off Memory Retention of Flow meter Counts.
User Friendly Indication.
Program Lock .
Alarm Output on ERROR In Cycle.
Display of total Cycle counts
Logical card with Operator interface is used for Basic Packaging Machine controller. In Basic MC controller all outputs [e.g. Clamp, seal, filler, Knife, Paper Pull etc] are controlled and synchronized with set delays and related inputs. Basic MC is used with filler [Weigher, Auger, Cup etc].
Various time delays [e.g. clamp on delay, seal time, knife time etc.] Can be Programmed
User Friendly operator interface with Keys, display and Indication LEDs.
Program Lock.
ERROR Operation stop safety In Cycle.
Input Output Test Mode
Paper Pull available Modes by Time base or Encoder with without Photo eye.
Modes available Auto Manual.
Door lock, heater ON etc. interlocks available for safety.
Independent Fill cycle, Paper Pull can be possible.
Logical card with Operator interface is used for Basic Packaging Machine controller. In Basic MC controller all outputs [e.g. Clamp, seal, filler, Knife, Paper Pull etc] are controlled and synchronized with set delays and related inputs. Basic MC is used with filler [Weigher, Auger, Cup etc].
Various time delays [e.g. clamp on delay, seal time, knife time etc.] Can be Programmed
User Friendly operator interface with Keys, display and Indication LEDs.
Program Lock.
ERROR Operation stop safety In Cycle.
Input Output Test Mode
Paper Pull available Modes by Time base or Encoder with without Photo eye.
Modes available Auto Manual.
Door lock, heater ON etc. interlocks available for safety.
Independent Fill cycle, Paper Pull can be possible.
This Controller Specially Designed To Measure %CE, %C & %SI For CI SG MALLEABLE Iron And Temperature Of Molten Metal, Also Controller having inbuilt Peak Temperature Indicator.
This Controller Specially Designed To Measure %CE, %C & %SI For CI SG MALLEABLE Iron And Temperature Of Molten Metal, Also Controller having inbuilt Peak Temperature Indicator.
Logical card with Operator interface is used for Basic Packaging Machine controller. In Basic M/C controller all outputs [e.g. Clamp, seal, filler, Knife, Paper Pull etc] are controlled and synchronized with set delays and related inputs. Basic M/C is used with filler [Weigher, Auger, Cup etc].
Features
Various time delays [e.g. clamp on delay, seal time, knife time etc.] Can be Programmed
User Friendly operator interface with Keys, display and Indication LEDs.
Program Lock.
ERROR / Operation stop / safety In Cycle.
Input / Output Test Mode
Paper Pull available Modes by Time base or Encoder with / without Photo eye.
Modes available Auto / Manual.
Door lock, heater ON etc. interlocks available for safety.
Independent Fill cycle, Paper Pull can be possible.
Logical card with Operator interface is used for Basic Packaging Machine controller. In Basic M/C controller all outputs [e.g. Clamp, seal, filler, Knife, Paper Pull etc] are controlled and synchronized with set delays and related inputs. Basic M/C is used with filler [Weigher, Auger, Cup etc].
Features
Various time delays [e.g. clamp on delay, seal time, knife time etc.] Can be Programmed
User Friendly operator interface with Keys, display and Indication LEDs.
Program Lock.
ERROR / Operation stop / safety In Cycle.
Input / Output Test Mode
Paper Pull available Modes by Time base or Encoder with / without Photo eye.
Modes available Auto / Manual.
Door lock, heater ON etc. interlocks available for safety.
Independent Fill cycle, Paper Pull can be possible.
Secondary Business TypeManufacturer / Exporters / Wholesale Suppliers
Opening Hours
SUN : Closed
MON : 9:30 AM - 6:30 PM
TUE : 9:30 AM - 6:30 PM
WED : 9:30 AM - 6:30 PM
THU : 9:30 AM - 6:30 PM
FRI : 9:30 AM - 6:30 PM
SAT : 9:30 AM - 6:30 PM
Akshay Electronics is a steady growing Solution provider Company in field of industrial automation, medical Electronics and Embedded systems. Established in the 1995, we at Akshay Electronics manufacture customized dedicated micro-controller based controllers for different OEMs. We are in this field for the last 10 years and have substantial experience and expertise. We have to our credit more than 2,500 installations all over India. We have got complete development, production and testing facilities at our unit. The company is fully equipped to take on design and manufacturing of customized product as per user requirements. The company is committed to meet user requirements meeting highest highest quality norms within stipulated deadlines and has acquired an impressive list of profile clientele due to its focus on ultimate customer satisfaction.
Reviews & Ratings
Write a Review
Post Free Ad
