Digital Flow Meter Dealers in Bhosari, Pune (6 products available)

• Weight: 0.82 kg
• Accuracy: +/- 0.5 percent
• Repeatability: +/- 0.15 percent
• Display Type: Digital
• Usage/Application: Industrial
• Flow Range: 1.9 to 57 lpm
• Maximum Pressure: 34kPa,0.3 bar
• Flow Range: 1.9 to 57 lpm
• Maximum working pressure: 10.3 MPa, 103
• Minimum working pressure: 34kPa, 0.3 bar
• Operating temperature range: -20°C to 50°C
• Storage temperature range: -25°C to 50°C
• Wetted parts: Stainless steel, PBT (polybutylene terephthalate) nickel, nitrile rubber
• Batteries: 2 AA alkaline
• Expected battery life: 6 to 12 months

• Steel: 1",2",3",1/2",1/4",4",6"
• Steel: 1",2",3",1/2",1/4",4",6"

within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a ratetotalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (pacf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60ã�â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from pacf to pscf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 ã�â±1.0%0.5% repeatability 1 ã�â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaftbearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: for other temperatures consult factory.

• Steel: 1",2",3",1/2",1/4",4",6"
• Steel: 1",2",3",1/2",1/4",4",6"

within the working range of the meter the rotor spins proportional to the actual velocity of gaseous material flowing. a pick-up sensor produces an electrical signal as each blade crosses through its low magnetic or rf field. this signal is amplified and conditioned by a transmitter or fed directly into a rate/totalizer, and represents the actual cubic feet per minute (acfm) flowing through the meter. the k-factor is stenciled on the meter body in pulses per actual cubic feet (p/acf). because gases are compressible, most people desire to measure the equivalent amount of gas corrected for the line pressure and temperature to standard cubic feet per minute (scfm at 60â°f, 14.69 psia). if the flow temperature and pressure are relatively constant, then a simple correction can be calculated to shift the k-factor from p/acf to p/scf and a simple totalizer (measurement systems india make ) may be used. when flow temperature and pressure are not constant, a flow computer. specifications linearity 1 â±1.0%/0.5% repeatability 1 â±0.25% maximum over-range 125% of flow rate for intermittent periods frequency output 0 to 1,100 hz voltage output approximately 100 mv@ 100 hz to 1.5 v (rms)@ 1,000 hz. pressure drop 0.5 psi at 100% of flow range pressure rating we manufacture flowmeters for most pressures. installation vertical or horizontal (any direction). materials of construction body: 316 l stainless steel. flanges: 316 stainless steel rotor: 431 stainless steel. rotor shaft/bearings: standard: tungsten carbide v-cup cartridge frame retainer: 302 stainless steel cartridge frame: 316 l stainless steel. temperature range:meter with bearing structure of: standard: tungsten carbide: -40â°f to 300â°f (-40â°c to 149â°c). for other temperatures consult factory.

• Brand Name: Mass Flow
• Size: 10mm to 1000mm
• Place of Origin: Pune, Maharasthra
• Condition: Good
• Feature: High durability, robust structure and resistivity to adverse

We offer Digital Gas Flow Meter as Per Customers’ Requirements. Our Standard Sizes are Up to 10 Inches and Can Be manufactured as per the needs of the customers. We are recognized as one of the prominent Digital Gas Flow Meter Manufactures, Suppliers and Exporters. These Digital Gas Flow Meters are ideally designed to measure the rate of flow of fuel gases consumed for Commercial Industrial or Residential purposes. The use of optimum quality materials in the manufacturing of the Digital Gas Flow Meter ensures high durability, robust structure and resistivity to adverse conditions. Details - Steel Insertion Type : Inline Type Sizes Available 10mm 15mm 20mm 32mm 40mm 50mm 65mm 80mm 100mm 125mm 150mm 200mm 250mm 300mm 400mm 500mm 600mm 800mm 1000mm     Temperature Compensation     Pressure Compensation Optional     Humidity Compensation     Density Compensation     Material Used - Steel    Types - Mechanical gas flow meter series EQZ Mechanical gas flow meter series TRZ GWF Volume Corrector ELCOR 2 SS Turbine Flow Meter Vortex Mass Flow Meter Thermal Mass Flow Meter Turbine Type Mass Flow Meter with Pressure and Temperature compensation Diaphragm Gas Meters Ultrasonic Flow Meters Coriolis Mass Flow Meters

Air / Gas Flow Meter, Industrial Oxygen Flow Meter