INE-Value Creators & Consultants (P) Ltd. Bhoiguda, Secunderabad, Telangana

The weld metal is available in measured quantities in packs, suitable for particular type of joint. The conventional pack contains the exact quantity of loose material in the pack which must be poured into the mould and to be ignited using the conventional flint igniter. to make the joint. The other type of the pack is capsule type where the material is sealed in a capsule and is ignited by passing the current using the special igniter. Exothermic Weld Powder Exothermic Weld capsule

Various types of Signal line SPDs are available to suit to the type of connections at the equipment such as PLCs, Scada systems. etc.

The Sectionalisers are normal Load break switches with built-in capability to open automatically. The Sectionalizers are designed to open based on the ‘fault count’ setting. The Sectionaliser trips in no-load condition, after Auto Recloser has opened and before it recloses again.

The Power line Surge Protection Devices (SPDs) are classified based on the location where it is installed (at the point-of-entry or at the point-of use) or needed and the connection (series or parallel). Several intelligent features are incorporated in the design of these SPDs to ensure that the SPD will function only in case of line surges rather than the nominal voltage fluctuations, thus enhancing the life and reliability of SPD.

MODEL: LSC ENCLOSURE RATING: IP 67 DIMENSION: 11.3 x 7 x 4.8 CM Produced according to IP 67 Non-resettable Currents detected from 2 to 100 KA Does not require external Power supply Certified by METU-Middle East Technical University LSC works with an inductive effect of the lighting strike current the events are monitored by a mechanical counter display LSC is a serial counter with 6 digit mechanical display unit FEATURES: The Lightning strikes are detected and monitored by LSC, which is able to give some information about the service necessity of the lightning system. By using an inductive record, the counter is able to accurately count all lightning events for a later reference LSC works with an inductive effect of the lightning strike current. The events are monitored by a mechanical counter display LSC is a serial counter with 6digit mechanical display unit It detect the lightning currents, which is more than 2KA LSC does not require any external power supply The lightning event counter shall be installed to the manufacturer’s instructions in a readily accessible manner so that readings can be taken at regular intervals. It shall be positioned such that it’s operating temperature is in the range of –10 deg C to +50 deg C The lightning event counter shall be robust, easy to install and housed in an IP67 rated enclosure. The counter shall operate from the energy of the lightning discharge and not rely on external or battery power to operate

The compound consists of a chemical solution of good electrical conductivity, which, when mixed with water and poured onto the earthing grid and surrounding soil, becomes a gelatinous mass which forms and integral part of the earthing system. The great advantage of the compound is that it will not wash away like most other earth improving mixtures. This reduces the requirement for redosing of the earth grid as is the case with most other earthing additives.

We provide the Switchgears up to 132kv substation applications. We carry out the turn key projects in this area from the system design, engineering documentation, procurement, installation & commissioning. In all the above areas, we take up the long term maintenance contracts for the systems and equipments supplied by us. We deal with ILJIN make GIS of 33kv and 132kv voltage level.

FTU is a kind of IED (Intelligent Electronic Device) for power system automation, which is a fully digitalized and microprocessor-based control device, and through connecting with this control device, Recloser can play a role of automated protection device.

Various types of Moulds are available to suit to the shape and size of the conductors to be joined with exothermic weld. We can prepare the mould for any new type of the joint.

This igniter is used with capsule type weld metal.

Exothermic Weld Materials Exothermic Welding process is a very efficient method of making high quality electrical connections and welding is used to create molecular bonds for various metals such as copper to copper, copper to steel, steel to steel, aluminum to copper and aluminum to aluminum. No external source of power is required for the welding. Exothermic welded connections use high temperature of reaction of powered copper oxide and aluminum. The reaction takes place in a semi-permanent graphite mould that lasts for fifty or more welds if properly cared for. The exothermic welding reaction takes place in a very few seconds, therefore the total amount of heat applied to the conductors or surfaces is considerably less than that employed in brazing or soldering. Tools of exothermic welding are very light in weight. So it saves time and the occupation or pay of a worker than others.

Different types of don conductors are used such as 25*3mm Cu tape or 25*3mm GI tape or 600V graede-50sq.mm, PVC insulated cable. Copper tape, 25*3 mm. Copper cable, 600V grade, 50 sq.mm, PVC insulated cable GI tape, 25*3mm.

Various types of Communication line SPDs are available to suit to the type of connections at the equipment such as Servers, LAN protectors etc.

  Cu Bonded Steel Rods (UL Approved) Copper bonded steel rod is M.S. Rod with first layer of nickel coating and then a copper Coating of 250 microns using electrolytic process. This Ground Rod possesses the strength of steel and conductivity of copper it has long life of more than 35 years as commercial GI pipe used for earthing. 5/8” Dia , 10 Feet Long , Molecular Cu coating > 250 micron 5/8” Dia , 5 Feet Long , Molecular Cu coating > 250 micron 3/4” Dia , 10 Feet Long , Molecular Cu coating > 250 micron 3/4” Dia , 6 Feet Long , Molecular Cu coating > 250 micron

Various types of Communication line SPDs are available to suit to the type of connections at the equipment such as MDF or a telecom device.

The Auto Reclosers are the Circuit Breakers with built-in automatic Reclosing and Opening capability (Auto Reclosing) under fault conditions. The auto reclosing functions are limited to preset number of times at preset intervals after which, it gets locked out. The auto reclosing feature is useful in avoiding the permanent shutdown in case of temporary faults.

MODEL: LC ENCLOSURE RATING: IP 67 DIMENSION: 11.3 x 7 x 4.8 CM FEATURES: The Lightning terminal can be checked by the forend tester any time The tester will indicate OK or FAULT with the help of red or green LED The test can be done from 100mtrs by means of connection cable

FOREND Advance Direct Lightning Strike Protection, Early Streamer Emission (ESE) Terminals The Principle of an Early Streamer Emission Lighting conductor is to artificially generate, with the aid of ionization mechanism, and early upward leader occurring before the other ‘natural’ upward leaders, in order to establish a priv