Dust Collectors Dealers in Hojiwala Industrial Estate, Surat (14 products available)

We are a prominent manufacturer and exporter of Pulse Jet Bag Filter based in india. the pulsejet bag fitter that we offer consists of filter cylinders (bags) enfolded in a metal housing. in operation, dust-laden air enters through the center of bag filter. either pressure or suction delivers the dirty air to the hopper. the fine particles travel upward and collect on the filter bags. the clean air passes through the bag and vents in to the atmosphere. a high-pressure jet of compressed air, which is directed through the bag, removes the dust, which is deposited in the hopper and is easily collected for disposal or recovered for use at timed intervals. anatomy of the pulsejet bag filter : the dust-tight pulsejet bag filter has three sections : a plenum at the top, a collector housing in the center, and a hopper at the bottom. a plenum (q) houses the blowtubes and supports for the solenoid valves. clean air or gas is released through the exhaust outlet ® in the plenum. the housing (m) contains the filter bag assemblies. below the housing is the hopper (o) which contains the inlet (n). a diffuser (t) in the hopper, adjacent to the inlet absorbs the impact of the high velocity dust particles and distributes the incoming air. pressure drop, that measures collector performance, is indicated by a d.p.gauge (s) connected at one end to the filter bag section and to the clean air plenum at the other end. a gujtex rotary airlock (p) is recommended as a discharge valve to handle the collected dust. filter cylinder assembly : the filter cylinders (bags) (a) slip over wire retainers (b). a bag clamp secures the bag-retainer assembly to the collar (c) of the venture nozzles (e), which are attached to a tube sheet (d). blowpipes (f) with orifice nozzles (g) are located above each row of filter bags so that the orifice nozzles are directly above the throat of each venture. the cleaning cycle : a signal from a remote sequence timer (h) actuates the opening of the normally closed solenoid or pilot valve (j). the opening of the solenoid valve decreases the pressure in the tube connecting the solenoid to the right angle diaphragm valve (k) causing the diaphragm valve to open. this permits a momentary jet of 100-psig air to flow from the air supply pipe (l) to blow tube, down each venture, and to each filter bag. all bags in a row are cleaned simultaneously.

• Brand Name: Symbio Sis
• Place Of Origin: Surat  
• Steel Plants: Furnace
• Palletizing Plants: Boilers
• Aluminum Smelters: Textile machinery
• Fertilizer & Petrochemical industry: Oil & Gas Exploration Installations
• Incineration: Cement & Lime
• Air Pollution Control systems: Coal Handling
• Product Type: Centrifugal Blower

"Usha Die Casting Industries (Industrial Equipment Division)" Specializes in the Custom Design & Manufacture of SYMBIOSIS Brand Industrial Fans and Blowers in materials of construction like MS, CS, SS, FRP Lined and in Impeller types like Backward Curved and Radial Blades. We offer a complete range of Sizes and Impeller Designs which allow us to meet all Industrial Air Moving requirements. Our company success is based upon our Experience, High degree of flexibility, Excellent product range and a Strong commitment to Quality Assurance. Regardless of the type of fan we recognize that Reliability is of prime importance. We understand that downtime is expensive for our clients and we do the Utmost to Design and Build our Fans with Reliability and Low Maintenance in mind. We cater to numerous applications for Blowers in industries and areas like. Steel PlantsFurnacePalletizing PlantsBoilersAluminum SmeltersTextile machineryFertilizer & Petrochemical industry Oil & Gas Exploration InstallationsFumes Exhaust for Welding and Painting Chemical & Paper IndustryAir Pollution Control systems Coal HandlingIncineration Cement & LimeWooden Furniture manufacturingPharmaceutical & DairyMan cooling application in hot areasFoundries The design of a centrifugal fan is mainly determined by the geometrical conditions of the installation. The following gives an overview of our most common designs. In addition we manufacture a large number of special designs to customer specifications. Types :- Direct Drive :- In most cases one attempts to use a direct drive. It is more compact, has less parts to be serviced and in most cases is cheaper than other designs.V-Belt Drive :- When fan speeds that cannot be achieved with direct drives or there are installation specific requirements, a V- belt drive is used. The motor mounting can be done in a number of different ways.Coupling Drive :- For accommodating a starting torque or variable torque e.g. when using the fan for material transport to be dampened while protecting the motor, then a drive using an elastic coupling is being used.Drive Positions :- Installation positions and direction of rotation of the Impeller for Centrifugal Fans defined from the Drive Side is given as below Note :- Outlet positions viewed from Drive sideFan Construction as per Application needs Optimized Direct Drive Selection :- As compared to belt-drive fan arrangements, direct drive fans are more compact, require less maintenance, and generally have a lower first cost. However, relative to belt-drive fans, they are limited in application, size, available features, and the ability to adjust to performance. A major objection to direct-drive arrangements in the past was the inability to adjust fan speed if system requirements changed. With the advent of variable frequency drives (VFDs) the speed, and therefore performance, of direct-drive fans can now be adjusted to meet varying requirements. Given the variety of operating speeds available, the only cost-effective method for selecting today�s direct-drive fans is software selection programs of SYMBIOSIS Blowers. Optimized V Belt Drive Selection :- In the lower horsepower ranges, V-belt drive selection is relatively simple, but as horsepower requirements increase, V-belt drive selection becomes more complicated and requires more consideration of the drive�s effects on fan and motor bearings. Optimized Heat Application Selection :- Fans handling hot airstream must be kept in operation after system shutdown until the airstream cools below 125°C. to prevent damage to the fan. The fan Impeller or shaft might otherwise distort due to �heat-soaking.� The shaft cooler is only effective while rotating. Burners should be located so that the air is thoroughly mixed before entering the fan inlet. Improper placement could cause hot spots on the fan wheel which exceed maximum design temperatures. Plug units Selection for Air Recirculating requirements :- Plug units are solidly welded, non-overloading fans which can be square panel mounted to the side or top of oven dryer panel. The mounting panel is insulated. These fans are designed for internal operation in furnaces, ovens or kilns where air has to be exhausted, re-circulated, or distributed. Plug units eliminate duct work and special mounting platforms. Construction Features :- Heavy-gauge welded components provide structural strength and durability.Continuously welded housings provide the strongest possible construction.Shafting is straightened to close-tolerance to minimize �run out� and ensure smooth operation.Lifting eyes provided on all fans.Impellers are dynamically balancedBearings are selected to provide long service life through the entire operating range of the fan. Impeller Designs :- Radial bladed impeller is non-clogging and is suitable for heavy dust loadings and materials handling. Although this design is less efficient than a backward bladed impeller, this fan can withstand the impact of large solids and the self-cleaning blade configuration prevents the accumulation of residue on the impeller. Backward Curved Impeller designs generally represent High Efficiency and cost effective Centrifugal Fans for both clean air and light dust loads. The absorbed power curve has a flat peak non-overloading characteristic. Peak efficiency point is on the steeply rising portion of the pressure curve and vastly superior to forward curved and radial wheel designs. Sound levels for these designs are lowest with the most efficient fan selections. Special & Customized Constructions :- Elevated Temperature Fans :- Fans can be constructed for elevated temperature operation with the addition of shaft cooler and guard and high-temperature paint. Note that the maximum safe Impeller speeds decrease as airstream temperatures increases.Spark Resistant Construction for Fans :- Intended to minimize the potential for any two or more fan components to generate sparks within the airstream by rubbing or striking during operation. This is generally exclusively customized as per specific application and requirements of the customer.Corrosive Applications :- Special steels or FRP Coating or Rubber Lining is offered for corrosive environment operation of fans. Balancing & Vibration :- There are many factors that can have a substantial effect on the Vibration level of air movement equipment; such as Wheel balance, Rotational speed, Drive components, Motor operation and Wiring. Providing equipment that operates well within acceptable Vibration levels requires Consistent Quality in Production and attention to details. At UDCI, we spend the extra time and money required to make this kind of commitment. Vibration is defined as "the Alternating mechanical motion of an elastic system, components of which are Amplitude, Frequency and Phase." The two components of Vibration that demand utmost attention are Amplitude and Frequency. Amplitude defines how far the Rotating body moves from the center rotating axis, and the frequency is the number of cycles, or revolutions that occur within a specified time period.

• Blower Type: Centrifugal blower
• Application: Industrial
• Power: 2400RPM
• Fan Type: ID
•  :  

Bag filter system is designed for optimum filtration performance. Its range provides filtration solution for a broad variety of fluid applications in the process industry. They are particularly useful for filtering large volumes of high viscosity liquids. Bag filter is constructed of filter housing, filter bags, internal cage to support bags, positive sealing arrangement & choice of end connections. The internal support ensures bags will not burst as high differential pressures build up during operation. FEATURES   High flow rates and low pressure drop. High dirt holding capacities. Efficiency as high as 98% and dust emission as low as 5 mg/Nm3. Easy to operate and low maintenance. Large area & heavy duty baskets. Housing made from stainless steel are mirror polished to resist adhesion of dirt and scale. Carbon steel housing are sand blasted, epoxy coated & finally painted with two coats of synthetic enamel. Multiple bag filter / Duplex bag filter / Jacketed bag filter unit designs.

• Color: Brown
• Voltage: 220V
• Automatic Grade: Automatic
• Power: 1-3kw
• Driven Type: Electric
• Warranty: 2 Years

The single Thickness Backward Curved Impeller is highly Efficient and only slightly less Efficient than its Aerofoil Counterpart. It has ideal Aerodynamic characteristics with maximum Design efficiency upto 82.4 %. It can be used for clean air or medium concentrations for medium to high pressure industrial applications. 9 different series for varying wheel designs allow flexibility in selection. This Design is uited for Harsh process requirements and is the most preferred choice for majority of applications. With years of application oriented experience and latest Manufacturing facilities, we manufacture these Impellers within close tolerences matching exact blade profiles using mechanized welding procedures. With welding distortion Management, maintaining minimal impeller run out before dynamic balancing and with special handling of Impeller, SYMBIOSIS delivers world class fans and blowers for your Critical applications   Our Blowers are truly SYMBIOTIC to your process. Think of Air…… Think of SYMBIOSIS Blower. We offer the Backward Curved Centrifugal fan in multiple sizes, arrangements, construction classes, impeller and housing widths. Whether standard or custom, each SYMBIOSIS Industrial Fan is designed and built with unmatched quality and backed by responsive service

• Power Source: Electric Blower
• Pressure: High Pressure
• Phase: 3
• Model Number: DT-CB-3
• Application: Industrial
• Body Material: PP/FRP

We are offering mechanical dust collectors. » adequate to coarse dust content gas capacity (100-1,00,000 ft.min.) adequate to high dust concentration. » trouble free operation long life » high collection efficiency (coarse dust) » low initial cost. » no maintenance required till 4-5 years » power consumption 0.5 hp » self discharging facility.

Self Supported Chimney, Oil & Gas Fired Thermic Fluid Heater

Replacement Filter Bag, micron cartridge filters, Industrial Evaporators

Cashew Dust Collector, Conveyor Belt System for Cashew Processing Steps

Chimney, pollution control equipments, Thermic Fluid Heaters

Pulse Jet Dust Collector Valve, Air & Oil Filter, Festo Roller Lever Valve