Back Back
Water Cooled Kickless Cable
FEATURES AND SPECIFICATION OF OUR BETTER QUALITY KICKLESS CABLES : 1. Design of Kickless Cable as per Customers Specification & Requirement and drawings. 2. High flexibility for good working efficiency. 3. Special type of Rubber hose with the good flexibility and its Pressure Capacity more than 10 Kg/cm2 and protect to high temperature water for safe operation. Covering of good pressure resistance, heat resistance, wear resistances. 4. Excellent cooling effect even in continued welding operation. 5. Fantastic water testing units with Pressure 10 to 12 Kg/cm2, Each & every cable is tested. 6. Little Impedance & little Reactance drop. 7. Copper wire size is 33 Gauge for 300 MCM & 400 MCM as per Standard of RWMA 8. Accurate copper straight lug or copper bend lug with 100% Conductivity of copper. 9. High resistance of repeating kicks & bending caused by electro magnetic force introduced by the welding current & welding operation, according long life. 10. Good Quality product with Long Life and reasonable rate. Long cable life reduces cable cost per weld – the true measure of cost cable. 11 Easy for check & replacement & maintenance. 12 The kickless cable is consuming part required to be inexpensive. 13 Expertise staffs’ are working in Electromech Corporation, last 15 Years experience in same field. 14 Immediately service is our motto. Technical data – Dual – Conductor Cable Based on 2g.p.m. @ 100o F temperature rise, maximum temperature 167o F. OHM’s per foot cable – both lead. 300 MCM 400 MCM 500 MCM 600 MCM 650 MCM 800 MCM Resistance ® per foot 0.0000836 0.0000625 0.0000502 0.0000422 0.0000388 0.0000312 Impedance(z) per foot 0.0000935 0.0000855 0.0000650 0.0000581 0.0000524 0.0000470
Water Cooled Kickless Cable
1. Design of Kickless Cable as per Customers Specification & Requirement and drawings. 2. High flexibility for good working efficiency. 3. Special type of Rubber hose with the good flexibility and its Pressure Capacity more than 10 Kg/cm2 and protect to high temperature water for safe operation. Covering of good pressure resistance, heat resistance, wear resistances. 4. Excellent cooling effect even in continued welding operation. 5. Fantastic water testing units with Pressure 10 to 12 Kg/cm2, Each & every cable is tested. 6. Little Impedance & little Reactance drop. 7. Copper wire size is 33 Gauge for 300 MCM & 400 MCM as per Standard of RWMA 8. Accurate copper straight lug or copper bend lug with 100% Conductivity of copper. 9. High resistance of repeating kicks & bending caused by electro magnetic force introduced by the welding current & welding operation, according long life. 10. Good Quality product with Long Life and reasonable rate. Long cable life reduces cable cost per weld – the true measure of cost cable. 11 Easy for check & replacement & maintenance. 12 The kickless cable is consuming part required to be inexpensive. 13 Expertise staffs’ are working in Electromech Corporation, last 15 Years experience in same field. 14 Immediately service is our motto. Unique Technical Features: 11 extra operations on each end of Electromech Kickless Cable These operations are necessary where wires are again crimped in an exclusive male and female pattern to position the wires to achieve the best alternate polarity design. This ultimately, results into less Kicks in Kickless Cable without any shorting of inside wires while in weld operation and hence increases the life by two to three times as per the feed back received form the industry sources. Operation 1 & 2 : Copper strip using for Wire crimping in Hydraulic press & then soldering on both end lugs. Operation 3 & 4 : Blanking of Non magnetic S.S. sheets - 2 times (One Male & One Female). Operation 5 & 6 : Forming of straight Pipe (male) and taper Pipe (female) Operation 7 & 8 : Spot Welding straight pipe (male) and taper Pipe (female) Operation 9 & 2 : Crimping into male type and other into female type. Operation 11 : Covering the male pipe with high quality imported heat shrink sleeve.
