Mold Temperature Controller Dealers

AQUA CONTROL SYSTEM is pleased to announce our new product of water controller unit "DOLPHIN"_ ACS 15 series and chiller.lt is widely used in plastic industries eg INJECTION MOULDING INDUSTRIES for Mould Temperature controller (MTC),EXTRUSION INDUSTRIES chilled roller Temperature controller and in CHEMICAL INDUSTRIES for chilled water circulation APPLICATION: 1.Water is common denomiator for every living thing on the earth. Water seeps through the soil and rocks and all the while it keeps on collecting a number of largely undesirable elements such as hardness agent, odour & chemical pollutant due to industries, DOLPHIN-ACS 15 will remove hardness from your water by passing through high exchange capacityion exchange base resin media within permissible limit (350 ppm to less than 5 ppm). 2.Numerous industrial processes run by supply and dissipation of heat surplus process heat is here drawn off by cooling with cold water from the customer.High performance water cooled compact chillers of the DOLPHIN-ACS 15 range increase productivity, shorter cycler times and reduce manufacturing cost. The resulting good level of efficiency causes low operatig costs,high reliability of operation and long life 3.In fact chiller have some limitation in temp.exactness.lt can work within 5*C to 10*c temp.different. Now it is necessary to use exact *C tempered water to get best performance in Injection Moulding Industries,Extrusion Industries as well as Chemical Industries while processing.DOLPHIN-ACS 15 take over this important task. In Injection Moulding Industries Mould temp.play an important roll to produce best Moulding.In Extrusion Industries the chilled roller should work within short temp. diffence say +/- 1*C. to get better performance. In this part of DOLPHIN-ACS 15 Water temp. range is 25*C-80*C. Microprocessor controlles developed especially for the application guarantee an exact temp. control. The compact design allows the installation even in case of restricted space.

The system is used for maintaining constant temperature of the mould during processing, which eliminates rejection and stresses in the moulded components, increase finish and shine. Oil based system for temperature of upto 150 degree C and water based system for temperature upto 95 degree C. Tank made out of SS and completely insulated. Pump mounted inside the tank, thus eliminating any chance of oil leakage. High pressure and seal less pump. Cooling coil provided inside the tank. PID Temperature controller used for precise and accurate control. Level sensor provided to prevent dry running of the pump. Portable and light weight. Duly powder coated.

Combined Model i.e. Oil & Water in one Compact in Size SS 304 Tank with Insulation Equipped with Castor Wheel

The Bry-Air offer superior quality Mould Temperature Controller BTC series which is designed to maintain constant temperature of Mould during the Moulding process. It is engineered to provide precise temperature control. This technology is increasingly being used to improve the quality of injection moulded parts and to avoid material wastage during injection moulding start up phase. Apart from its functioning it has an exquisite appearance and is small in size, also it is convenient for mobility as the unit is mounted on wheels. Widely demanded in various industries, our range is known for its reliability & accuracy. We provide these in different specifications to meet the diverse demand of customers in different Industries with different application areas worldwide. The state-of-the-art design of our Mould Temperature Controller is seen in high quality injection plastic mould like automobile Industry, medical plastic industry, white goods industry etc. Bry Air Mould Temperature Controller is available in water and oil.The temperature can be maintained between 40 – 90°C in case of water and 40-150°C in case of oil. Advantages of Bry Air Mould Temperature Controller:   Simple & compact design Suitable for all kinds of mould for Injection Moulding Machine Precise temperature control Easy connection for supply & return cooling circuit, by hose nipple

STC series automatic mould temperature controller is mainly used to bring the mould to a specific operating temperature and hold that temperature constant by heating andor cooling a Circulating fluid heat transfer medium.

As our Mold Temperature Controllers have gained huge popularity in the global markets, we have become the reliable name involved in its exporting and supplying. Compliant with the set industry standards, our Mold Temperature Controllers are safe to use and highly efficient.

JD series automatic mould temperature controller is mainly used to bring the mould to a specific operating temperature and hold that temperature constant by heating and/or cooling a Circulating fluid heat transfer medium. This series adopts heat-exchanging principle,using water or high-heat-conduction oil as transfer medium. Unstable temperature in the process of mould forming always tends to produce unqualified products. According to the principle of heat exchange, JD’s mould temperature controls make use of water and high property heat transferring oil as a medium to keep a proper stable temperature in the process of mould forming so as to guarantee high quality of products and raise the productive efficiency.   Features: Mould Temperature Controller – Hot medium liquid : Water or oil convertibility, Either water or oil can be used as a hot medium liquid according to the needs of mold forming temperature. Its high selectivity is certain to bring in high economic efficiency. While most of the MTC’s (Mould Temperature Controller) only support one medium, Our MTC (Mould Temperature Controller) supports both Water and Oil Medium. – Vertical Pump: The flow of vertical pump can be always kept steady, making its service life long and durable. – Stainless medium tank: Our Mould Temperature Controller’s interior tank will not get rust for long term, which is sure to prevent from any blockade of pipes and keep long-term service of pump. – Transparent water (oil) level viewer: The transparent water (oil) level viewer can easily be used to view and inspect the quantity of medium liquid and be reminded to refill the medium liquid from time to time. – Automatic alarming device: While water (oil) shortage occurs in the container, this device will automatically light up and start alarming and cut off the electric power of heaters and pumps, thus guaranteeing the machines (MTC) safety as well as the person running it. – High-precision automatic temperature control: The measure of temperature is very sensitive and accurate, little change of temperature helps to keep products both fine and delicate. – Minimize Products Wastage: The mold can reach the required temperature right at the beginning of operation, thus can obviously minimize products shortage. – Maintain proper temperature: Either in continuous operation or in temporary shutting down, mold-forming temperature can always be kept proper to guarantee the best quality of products and further improve the forming process.   – Compact in size, light in weight: Easy to install, convenient to operate, convenient to move and little room to occupy, our Mould Temperature Controller (MTC) is perfect choice for any Company running any kind of mould.

We offer Mould Temperature Controllers to our clients. These are used to maintain a mold at a constant temperature, and also eliminate stress in the molded components. These controllers are manufactured using quality materials and are tested by our experts before delivery to our clients. The product is known for its reliability, accuracy, high performance and long working life. Additionally, we provide these at reasonable prices in different specifications as per the client's requirements.     Features: Oil or water based models available. Tank made out of S.S. & completely insulated. Pump mounted inside a tank , thus eliminating any chance of oil leakage for models upto 180o C Special graphite seals for models upto 300o C Digital Temperature Controller/PID used for Procession accurate Temp control. Safety Thermostate used. Direct/ indirect coolings coil used to keep temperature control accuracy at +2o C Portable, mounted on castor wheels.   Models: Upto 180o C Upto 300o C Model upto 300o C Also available for Aluminium Die Casting application (upto temp. of 400 degrees)

Stainless Steel Corrosion proof material for all components coming in contact with water. Automatic water re-feeding. Over-Heat trip thermostat. Pump overload relay with indication and hooter. Brass y-stainer at inlet and outlet. Stainless Steel, well insulated tank for power saving. Plate type heat exchanger.

The extremely economical GMC Series accurately monitors and maintains temperatures to within 1 degree of set point, and maintains the optimum production temperature by sampling mould temperature four times every second. As a result, target temperatures are hit with precision and are accurately maintained cycle after cycle, maximizing output and minimizing rejects.

Range 12-1500Kgs. Main Features :  The main machine adopts high efficiency mini hot water pump or oil pump with reliable function, small size and light weight. Adopts imported digital temperature control gauge. Can improve the color of product and stabilize the quality of product. Application: Use in plastic and rubber industry, chemical and pharmaceutical industry, textile industry and any other situation where temperature controlling necessary.Use in producing plastics which high temperature mould necessary and high accuracy necessary.

We supply a qualitative range of Mould Temperature Controllers that are manufactured by us using optimum grade raw material. These are specifically designed to maintain invariant temperature of mould during the entire moulding process. Widely demanded in various industries, our range is known for its reliability, accuracy, high performance and long working life. Further, we provide these in different specifications to meet the diverse choices of clients.

The Bry-Air offer superior quality Mould Temperature Controller BTC series which is designed to maintain constant temperature of Mould during the Moulding process. It is engineered to provide precise temperature control. This technology is increasingly being used to improve the quality of injection moulded parts and to avoid material wastage during injection moulding start up phase. Apart from its functioning it has an exquisite appearance and is small in size, also it is convenient for mobility as the unit is mounted on wheels. Widely demanded in various industries, our range is known for its reliability & accuracy. We provide these in different specifications to meet the diverse demand of customers in different Industries with different application areas worldwide. The state-of-the-art design of our Mould Temperature Controller is seen in high quality injection plastic mould like automobile Industry, medical plastic industry, white goods industry etc. Bry Air Mould Temperature Controller is available in water and oil.The temperature can be maintained between 40 – 90°C in case of water and 40-150°C in case of oil. Advantages of Bry Air Mould Temperature Controller:   Simple & compact design Suitable for all kinds of mould for Injection Moulding Machine Precise temperature control Easy connection for supply & return cooling circuit, by hose nipple

The Automatic mold temperature controller works on heat exchanging principle using water or oil to precisely control the mold temperature, this reduces the production time and thus produces quality product. One of our main objectives is to offer high quality products and to achieve this goal all our products undergo vigorous tests.Two types of Mold Temperature available Water & Oil Mold Temperature Controller