Cyclone Separators Dealers

Gas Cyclone Technical Description One area of application of gas cyclones is the pre-filtration of solids from gases. Gas cyclones have no moving parts, and so are low-maintenance systems. They can also be used in conjunction with high gas temperatures. For these reasons they are in widespread use. This trainer was developed in cooperation with the Institute for Solids Process Engineering and Particle Technology at TU Hamburg-Harburg. A disperser is used to disperse the feed material (quartz powder recommended) finely in an airflow. The airflow laden with solid material (raw gas) in this way is fed tangentially into the cyclone at the top. In the cyclone, the airflow moves downwards as a rotating primary vortex. At the bottom of the cyclone the vortex is reversed. In the middle of the cyclone it moves as a secondary vortex back up towards the immersion tube, where the cleaned gas emerges from the cyclone. The main separation process takes place in the primary vortex. Owing to the centrifugal forces and the difference in density between the air and the solid, the coarse solid particles move towards the wall. They slide down the wall and are collected in a tank at the bottom of the cyclone. No complete separation of the entire solid material takes place. The fine particles which are smaller than the separation size are ideally discharged from the immersion tube at the top with the secondary vortex. This fine material is separated out of the air flow by a filter. The separation size defines the theoretical boundary between the fine and coarse material. The solid content of the raw gas can be adjusted by means of the disperser and an airflow control valve. To prevent loading of the airflow with particles upstream of the disperser, the drawn-in room air is filtered. An air suction fan generates the airflow. Pressure measurement points at the relevant positions in the trainer enable to determine the pressure loss. For particle size analyses of the feed and the coarse material, a balance and a screening machine are recommended.

Cyclone Separators are normally used for collecting various types of Coarsed dust particles, in which dust laden gas enters a cylindrical chamber Tangentially at one or more points and leaves through a central opening. The dust particals by virtue of its intia, will tend to move towards the outside Wall from which it led into a receiver. The Cyclone is made of sheet Steel (M.S or SS).

CY-800 / -950 / -1200 / -1400 / -1600 / -1850 The CY cyclone is in standard construction furnished with air valve.

Cyclone Separator is simply fabricated construction from M.S. /S.S. material. In this, air entry is tangential so, due to tangential entry of air there is cyclone produce in cyclone separator and all heavy dust particles are fallen in bottom of hopper and clean air remove from the top of cyclone. Also, we can supplied multi cyclone as per customer requirement.Details : Capacity : Up to 20,000 CFM Material of : M.S / S.S

We have carved a niche as an eminent Manufacturer, Exporter and Supplier of Pneumatic Cyclone from Punjab, India. The Pneumatic Cyclone offered by us is generally used in flour mills for splitting grain and air. Our products display accurate result and high durability because of which they are favored by clients in various agro industries. Owing to our large distribution network, we ensure quick delivery of Pneumatic Cyclone to clients all over the world.Features : Durable nature Provide accurate performance Less maintenance

UNICON Cyclones and Multi Cyclones are used for collection of coarse dust particles in cement industries and steel industries. Our cyclones are effectively designed to remove dust with an emission level upto 200 mgm3. The pressure drop across the cyclones are as low as 50-100 mm WG resulting in energy savings.

Cyclone separators are devices that are used to separate dust from dust laden gases typically when the dust particle size is 20 microns or more. Filtration efficiencies in cyclones are not as good as Bag Filters, however the maintenance cost of cyclones is much lesser than that of Bag Filters.

Cyclonic separation is a method of removing particulates from an air stream, without the use of filters, through vortex separation. Rotational effects and gravity are used to separate the particle from the dust laden air. Cyclone body will be cylindrical in the top portion and conical shape at the bottom as shown in the drawing. The air stream will enter into the cyclone body tangentially in the top cylindrical with high velocity. The top portion of the cyclone body guides the air to move in a circular path in high velocity. A cyclonic effect (twister) will be created inside the body and the air stream move downwards in the heavier dust particles in the helical pattern. The heavier particles in the air stream have too much inertia while moving in cyclonic effect and move towards outer peripheral of the cyclonic effect in the air stream. When the particles are striking the inner surface of the cyclonic body, it will lose its momentum and fall down. In a conical system, as the rotating flow moves towards the narrow end of the cyclone, the rotational radius of the stream is reduced, thus separating smaller and smaller particles.               Cyclone is called as pre-collector in the dust extraction system. Cyclone has good efficiency in dust separation for large size particles and fiber dust particles. Cyclone separator will be used to segregation of items or products in the conveying systems. Cyclone separator MOC will be defined by the application and nature of dust to be handled. Cyclone separators widely used in Wood industries Flour mills Pneumatic conveyors Coir mattress Fibre glass Buffing & Polishing Boilers and furnaces exhaust Bulk drugs

With the support of our advance infrastructural unit and diligent workforce, we are offering a customized assortment of Cyclone Separator to the clientele. Our Cyclone Separator is working smoothly with great capacity.

Cyclone Separators   • Cyclone separator is used for collection of coarse dust particles • We are manufacturer of the efficient and durable cyclones • Product ranges from adequate to coarse dust content gas (100 to 100,000 fts/min) • Due to whirling motion gases & dust particles are separated • Cyclone separator used for control of coarse dust of high concentration • Multi cyclones are also provided • Our cyclones have high collecting efficiency