Elmex Controls Pvt. Ltd. Makarpura, Vadodara, Gujarat

While standard Screw Clamp or Spring Clamp terminal blocks are designed for direct connection of conductors, (solid, stranded, flexible), simply after stripping the insulation, there are other wiring practices and applications where conductors have to be provided with ring type or fork types lugs, for more secured connections.

The Panel Mounted terminals of elmex range are so designed as to fit on any panel surface. The terminals are stackable and can be fixed on the surface with the help of fixing screws at the end.

These Current Transformers are designed for secondary current of 1A or 5A and the primary current ranging from 5A to 7500A depending on the application of the system load current. Basic Construction in three different Groups, meeting various application requirements: Polycarbonate Encapsulated Rectangular Ring Type CT

junction box for electrical connection from PV Crystalline module as a solution for easy and reliable interconnection from PV module to DCAC converters. ‘elmex’ Junction Box has simple and cost effective assembly designed with snap fit locking arrangement with IP 65 protection sealing requirement for PV industry.

The junction box is provided with two cables each of 1 meter length with ‘elmex’ male and female EMPV4 connector for simple on-site process.

junction box for electrical connection from PV Crystalline module as a solution for easy and reliable interconnection from PV module to DCAC converters. ‘elmex’ Junction Box has simple and cost effective assembly designed with snap fit locking arrangement with IP 65 protection sealing requirement for PV industry.

solar connectors is provided with hexagonal nut for fixing and tightening it on the mounting surface: a rubber o-ring is kept between panel surface and the wall of the photo voltaic devices. ‘elmex’ connector has mating compatibility with ‘elmex’ make straight connector EMPV4.

Country of Origin : 1000 V DC

The combiner box is an interface between the array and invertor. This component is very important for the smooth operation of a solar installation. All components are characterized by a high degree of reliability. The robust design enables uninterrupted operation even under unsmooth conditions

solar boxes has simple and cost effective assembly designed with snap fit locking arrangement with IP 65 protection sealing requirement for PV industry.

slotted channel used have accurate dimensions within permissible tolerances. If the mounting dimensions are less than specified then the attachment of the terminal blocks on these rails will not be strong enough and there could be problems of loose fittings and at times terminal blocks may get dislodged from the channel even in normal service conditions.

Interconnecting links or shorting links are used to interconnect two or more terminal blocks of same type and at the same potential. it is recommended that factory made shorting links which are designed considering the rated current of the terminal block and its pitch are used for interconnection purpose rather than looping by wire which is not a reliable practice.

Stud Type Terminals in Melamine Housing are specifically developed for termination using Ring Fork Type Lugs and provide a very reliable connection against vibration. They are available in two types : 1) Screw driver operated 2) Nut driver operated The range covers terminals for conductor sizes from 0.5 sq mm to 35 sq mm

The fuse holder is made of special grade phosphor bronze and hence offers low contact resistance. A solid brass link type DL4 in place of the fuse makes it possible to use it as a disconnection type terminal block. KUDDF4 is a fuse terminal and a standard terminal block (feed through) combined in one housing, giving cost, time and space economy.

we are adding instruments transformers, both current & voltage Transformers to our range of product. Group of Current Transformers designed & constructed in compliance with below standards: Transformers have been successfully tested in ERDA, Vadodara for type test as per IEC: 61869-2. ‘elmex’ has set up all the test facilities in- house to conduct all routine tests as well as certain type test.

Distribution blocks are an Innovative Engineering Solution to satisfy customer's needs. They find application in Power Distribution for Control Circuits and can also be used to centralize earthing for the entire panel. These blocks are completely shrouded and accommodate single input and multiple outputs. They replace conventional open Bus-Bars, ensuring perfect continuity

electrical industry & providing termination solution for the last five decades & Now serve larger segment of this industry, we are adding instruments transformers, both current & voltage Transformers to our range of product. Group of Current Transformers designed & constructed in compliance with below standards:

elmex Micro Terminal Blocks are small in size and light in weight, yet functionally same as Standard Terminal Blocks. They are specially developed for installation where space is extremely limited but the same cable density is required as in a normal situation. They can be mounted on TS 15 Rail, which is also smaller, lighter and more economical than TS 32 and TS 35 Rails. The terminals are recommended for use in industries like elevators, automation etc.

Marking labels are used for identification of circuit connections. Marking of terminals helps in easy identification and quick maintenance. Marking labels are made of Polyamide in white colour and pre-printed with black indelible ink. They are used to serve different purposes like alpha-numeric identification required for accurate wiring and trouble shooting. Marking labels are available in strips containing 10 markers.

low tension current transformers’ has been serving electrical industry & providing termination solution for the last five decades & Now serve larger segment of this industry, we are adding instruments transformers, both current & voltage Transformers to our range of product.

A thermocouple is a bi-metallic junction ie a junction between two different metals that produces voltage related to temperature difference. Thermocouples are classified depending on different alloys used for different temperature ranges.Thermocouple terminal blocks are constructed using the same type of metal alloy as that of thermocouple intended for measuring temperature. Thermocouple terminal blocks are used in pairs.

These Terminal Blocks accommodate a glass cartridge fuse of 5 mm x 20 mm, 5 mm x 25 mm or 6 mm x 32 mm size. The fuse holder is made of special grade phosphor bronze and hence offers low contact resistance. A solid brass link type DL4 in place of the fuse makes it possible to use it as a disconnection type terminal block. KUDDF4 is a fuse terminal and a standard terminal block (feed through) combined in one housing, giving cost, time and space economy.

Applications in Control & Automation require fuse protection facility. elmex offers Terminal Blocks with built-in safety fuse levers. These Terminal Blocks accommodate a glass cartridge fuse of 5 mm x 20 mm, 5 mm x 25 mm or 6 mm x 32 mm size.

The proven screw clamp & spring clamp design offers high contact force and is easy to use. The range covers terminals for conductor sizes from 0.5 sq mm to 95 sq mm for screw clamp and 0.5 sq mm to 16 sq mm for spring clamp.Spring Loaded Terminals employ compression springs below the contact clamp assembly, for better and more reliable connection for high vibration applications.

The range covers terminals for conductor sizes from 0.5 sq mm to 95 sq mm for screw clamp and 0.5 sq mm to 16 sq mm for spring clamp. The special foot design provides the slot for easy mounting and removal of a single terminal from the stack, using a screwdriver.