Rust Converter Dealers in Mumbai

RUST-X VCI Neutracoat Xtreme is a latex based primer, which can be applied with a brush or spray on the parts to be protected. The compound first converts the corrosion and then leaves a latex based layer on the surface which has a high salt spray life. The total action time is approx. 1-3 hours depending on the environmental conditions in which it is applied. It is highly active against corrosion conversion for the most damaged products that are hard to shot blast, sand blast or phosphate and works in extreme environmental conditions and provides long-term corrosion protection to the parts on which it is applied. The liquid is transparent or can be of any chosen colour upon application. The VCI Neutracoat Xtreme remains liquid even after years of application. This therefore does not cause any dimensional changes on the part. The VCI Neutracoat Xtreme is compatible with Engine, Hydraulic and Transmission fluids and does not cause any detrimental effect on the same. VCI Neutracoat Extreme converts the metal surface layer in a chelating layer that converts the surface into hydrophobic passive layer. This is later than converted into a solid film due to the presence of water based latex polymers that works like a primer and prevents further corrosion. If very high salt spray life is required, then the layer can be plated or applied with thicker paints either water or solvent based.   How to Use:   Clean the area to be protected using a cloth or RUST-X 40 spray Apply the RUST-X Neutracoat Xtreme with a brush on the area to be protected Ensure that all the area gets covered evenly with the compound Check the reaction with the metal used before commercial application   Application and Handling    This can be used to protect structures, chemical plants and equipments that are intended for outdoor storage or are located in open areas and need protection. These can also be used to protection unpacked refinery equipment oil pipleline equipment and valves, off shore refinery parts which are not painted or coated and require protection or during the storage while commissioning, for lay-up during shut downs and also on heat exchangers, wind mills and automotives. Due to a higher drop point the VCI Neutracoat Xtreme it can be used on the chemical plant and equipment, which is in operation at elevated temperatures. This can also be used to protect Defense Equipment and installations where extreme climatic conditions may have detrimental effect on the properties of the equipment e.g. on cannons, guns, artillery, launch vehicles etc. It can be applied on the machined surfaces of automotive equipment such as Transmissions, Gear Boxes, Engine Blocks, Flywheels, Hydraulic Pistons or other machined and unpainted surfaces to keep them from corrosion during storage and transportation.     Packaging Available  25 ltr Can & 210 ltr Barrel   Safety Information  RUST-X oils donot contain Lead (Pb), Mercury (Hg), Cadmium (Cd), Hexavalent Chromium (Cr6), Polybrominated biphenyls (PBB), or Polybrominated di-phenylether complying with the re-stricted substances listed in Article 4(1) of the RoHS Directive. RUST-X Rust Preventive Oils are also REACH Compliant for exports to the European Union.

• Type: Rust Converter
• Purity: 99%
• Form: Liquid
• Application: Industrial Use, Domestic Use
• Packaging Type: Drum and Can
• Brand Name: Meproche

Our company is offering quality Meproche C-21 rust converter, that is based on polyhydroxy organic compounds It is efficiently used to remove rust from stored steel and old rusted steel already erected (whether in RCC or otherwise) With the chemical Meproche C-21 rust converter, pitted surfaces can be converted into a protective coat. It is supplied in two packs. A surface treated with Meproche C 21 accepts primers and paint fast. It increases adherence of primers and paints and thus improves the life of paints It covers approximately 70/75 square meter per Kg.   Method of application: Mix 50 gms of part A to 0.950 kg. of part B Apply on the rusted surface and leave it for 4 to 6 Hrs Remove rust by wire brush Repeat the process if necessary The chemical converts the balance rust into a passive state thus stop further rusting It provides temporary solution for rust prevention. It can later be painted or lined Rubber gloves should be used while handling Meproche rust converter as it is mildly acidic in nature   Note: The information provided is based on our experience and tests conducted by us on typical specimen However, the actual working conditions are beyond our control and knowledge Hence, we are not responsible for any liability for loss, damage, injury or mishap resulted

CVC RUSTKOTE-300 is a new generation protective coating, which converts existing rust on metallic surfaces into a chemically inert coating, which prevents further rust and provides a suitable base for painting immediately. RUSTKOTE-300 is a neutral solution of active chemical ingredients incorporating mineral acids, solvents, stabilizers and additives. It saves expensive and time consuming scrapping of tenacious rust by sand blasting etc. RUSTKOTE-300 can be used on rusted as well as clean metal surfaces. Due to the formation of inert coating, further rusting is totally stopped. It reacts with the loose and adherent rust on the metal surface and converts the rust into a very inert and adherent organo-metallic coating.

Rust Converter The distinctive formula of this product accounts for its dual functionality. Rust Converter 177 is a single pack ready-to-use solution which on applying converts the existing steel rust into a stable metal complex by forming a polymeric film over it. The Polymeric film acts as a protective and passivative coating preventing further corrosion which in turn acts as an ideal base for painting.

• Converts existing rust into stable metal complex, forms protective coat and prevents further rusting: Eliminates complicated usage of sand blasting,wire brushing and mechanical grinding, saving time and labour

Rust Converter 177 is an innovative product based on the latest technology in rust converters. The distinctive formula of this product accounts for its dual functionality. Rust Converter 177 is a single pack ready-to-use solution which on applying converts the existing steel rust into a stable metal complex by forming a polymeric film over it. The Polymeric film acts as a protective and passivative coating preventing further corrosion which in turn acts as an ideal base for painting.Rust Converter 177 reacts with all the layers and forms a stable non-reactive complex organo-metallic surface having bluish-black colour. In addition, this innovative product arrests the migration of ions, preventing electro-chemical corrosion process and prolongs the paint life for a reasonable period of time, resulting in considerable savings.

rust converters, anti corrosive paints, Rust Converter Primer

We are offering rust converter. Converts rust to a tough polymeric coating.

automobile coatings, Fire Retardant, polyester extra soft putty

Shreejitreat RC is a rust converter, an advanced remedy in the field of rusting or corrosion of iron & metals. It works by converting rust into metallic complex. The treated surface becomes browngreyblack colored within a short time, which prevents further rusting.

cyanoacrylates adhesives, Red Insulation Varnish, hid ballast, pipe sealants

engine room plating, hull plating

Rustocon Rust Converter and Remover

machine cutting oil, rust preventive coating, Viscous Lacquer