Epoxy Coatings Dealers in Navi Mumbai

These are Coatings which protect and repair various industrial equipments, which are already affected or likely to get affected by severe corrosion, erosion and chemical attack. These coatings are found to be the most economical solution against Sea water attack. Our glass flake systems have extremely low permeability, good resistance to undercutting, good chemical resistance, relatively high abrasion / erosion resistance & minimal shrinkage.

• Type: Conformal Coating, Industrial Automation
• Form: Liquid
• Brand Name: ASS
• Application: Industrial Use
• Pack Size: 400 ml, 500 ml

Features of ACC 2010 Acrylic Conformal Coating ACC 2010 Acrylic Conformal Coating is a flexible transparent acrylic coating for the protection of electronic circuitry formulated to meet the highest resistance requirements. Used on printed circuit boards as protective coating against moisture, dust, humidity and fungus. Protects all Electrics/Electronics Circuitry equipments in Extreme Service Environments. Excellent adhesion and dielectric properties. Good moisture resistance & Quick Evapouration.   Application of ACC 2010 Acrylic Conformal Coating It used as extra/after insulation of coils and transformers and reduces operational noise. Military Equipment Aerospace Industry Air Conditioner Circuit Board Industrial Applications Automotive Applications   Direction of ACC 2010 Acrylic Conformal Coating Shake well can before use at least 1 Minutes.Hold the can at least 15 to 20 cm from the surface you are spraying and keep the can upright during use. Protect & Mask areas not Coated. Two light coats is best results better than one heavy coat.Coating becomes dry in 20 minutes. make sure the surface is completely dry before using. completed cure takes place in about 24 hours depends upon the humidity. When finished spraying, clean the aerosol valve by turning the can upside down and pressing the button until only propellant escapes.   Precaution of ACC 2010 Acrylic Conformal Coating Contains gas under pressure do not punctured ,may explode if heated. Extremely flammable aerosol. Prevention : Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Pressurized ontainer: Do not pierce or burn, even after use. Do not spray on an open flame or other ignition source. Use only outdoors or in a well-ventilated area. Avoid breathing vapor. Wash hands thoroughly after handling. Causes serious eye irritation. May cause drowsiness and dizziness Response : IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations.   Storage of ACC 2010 Acrylic Conformal Coating Storage : Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. Store in a well-ventilated place.keep container tightly closed. Keep Out of Reach of Children

• Speciality: Waterproof
• Type: Crystalline Waterproofing Coatings
• Certification: ISO 9001:2008
• Shelf Life: 1Year
• Color: White
• Purity: 90%
• Country of Origin: India
• Waterproof: Yes

vitcon 2012 flexikote is an elastomeric premium quality acrylic based coating best suitablefor any waterproofing applications. the high solid acrylic content makes vitcon 2012flexikote more durable and effective for protection of concrete as well as metal structures.advantages: excellent resistance to ultraviolet radiation. excellent bonding to all building substrates. forms a durable waterproofing breathable coating. reduces water permeability. improves resistance to alkali and carbonation effect. suitable for use in slightly damp conditions. applications:substrate preparation:the substrate to be treated has to be thoroughly cleaned and all loose particles, oil, grease, dust etc. should be removed. the cleaned surface then needs to be washed with clean water.for hairline cracks on concrete surfaces, thorough cleaning is recommended. but for cracks more than 2 mm has to be opened and cut in a shape of “v” groove. the cut groove is then filled with cement mixed with either vitcon 2013 sbr or vitcon 2011 polykote depending upon the size and nature of cracks.  

Bonded dry film lubricants can be thought of ashigh performance, paint-like coatings consistingof fine particles of dry lubricants blended with abinder and special additives. After applicationand curing, these lubricants bond to the substrateand form a solid film. The film reducesfriction and increases wear life. Dry film lubricants contain special materials thatreduce friction and wear by preventing surfaceto-surface contact between mating parts. Theirperformances vary depending on the specific lubricantused. Some offer excellent lubricationand corrosion protection, while others operate athigh temperatures or under high loads. Some are formulated for use in extreme environmentsand can withstand chemicals & radiation.Dry films generally provide a thin film (10 - 100microns) of resin binder with suitableadditives. Dry Film coatings are widely used for one ora combination of the following reasons : Components are operated in corrosive atmospheres Components may be stored for long periods oftime Permanent lubrication is desired (such as inaccessibleparts) Operating pressures exceed the load bearingcapabilities of oils and greases Parts are subject to frequent disassembly Where clean operation is desired (DryFilms will not collect dust, dirt and debrislike greases and oils) Where a protective coating or sacrificialbreak-in lubricant is needed (pistonskirts) Where fretting and galling is a problem(such as splines, UV Joints etc.)

We are offering trephine kit with coating for easy guide surger and bone grafting procedure autogenous.

• Size: 40x40inch, 45x45inch, 50x50inch
• Thickness: 0-3mm, 3-5mm
• Pattern: Plain
• Feature: Accurate Dimension, Epoxy Resistant, High Strength, Quality Tested
• Floor Use: Floor Use
• Storage: Dry Place & Cool Place

With our fully in-house setup as in Powder Coating and latest CNC machine, a dedicated team of programmers, designer, and operators work hard along with this state-of-the art machinery to offer complete solution to the customer.   With 23Ton of punching force, 500 x 500 part shoot, 2.5Meter without repositioning machine along with wide range of tooling we are able to achieve critical componets with high accuracy amd minimum leadtime. Moreover availablity of In-house powder coating plant boosts our efficency and provides our customer with full soluton under one roof.

UV curable coatings offer several advantages over conventional thermal cured or air drying coatings. E.g. UV cured coatings are fast drying – curing in few seconds, high gloss, offer high scratch & abrasion resistance, do not require heat during curing process etc. This makes them ideal for heat sensitive substrates like plastics.We offer high quality & customized solutions for UV coatings for plastics.

• Applications: Printed Circuit Board, Electronic components etc.
• Pack Size: 300 gm (400 ml) Aerosol Can

It provides clear, colourless and wear resistant coating to electronic circuitry. Quick drying and scratch resistant protects circuitry from dust and moisture. Also used as an anti-corrosion coating for PCB’s and other components. If needed allows re-soldering.

• Classification: Self Dispersing, Self Levelling, Mortar Epoxy Coating
• Types: Solvent Based
• Brand Name: Metcon
• Usage/Application: Industrial Use
• Color: Any
• Coating Type: Eopxy
• Surface Finishing: Smooth

This is two pack coal tar epoxy coating for metal surfaces . It has good corrosion , abrasion and water resistance. Recommended Uses Ideally suitable for use in varied conditions for the protection of all types of metals especially for the substrates which are having marine exposure.

KEM REPEL 111 is a ready to use all purpose colourless water repellent. Easy penetration to masonry substrates. Acts as a damp proof course when injected.

• Features: Customized,Reliable,Durable,Optimum quality,Exceptional finish

• Packaging Size: 30ml SIO3 Ultra Wet Look ( Body) 20ml SI02 Safety Vision(Wind Shield)
• Packaging Type: BOX
• Surface Finishing: Wet Look / 9H + Hardness
• Thickeness: 8 Micron
• Brand: NANO-CERAMIC

• Color: As Per Buyer Need
• Packaging Size: As Per Buyer Need
• Grade Standard: Industrial Grade, Chemical Grade
• Types: Solid , Water-Based, Solvent-Based
• Category: Floor Coating, Wall Coating, Steel Coating, Metal Coating
• Feature: Chemical Resistant, UV Resistant, Abrasion Resistant, Non-Slip

Our range of coatings cover most industries from metals, marine, appliances, buildingsinteriors, automotive, construction etc. Our coatings are based on Alkyds, Epoxies and Polyurethanes. Alkyds - The range of Alkyd coatings possess special properties like low glass transition temperature and good wetting ability. They are also modified for different properties like enhanced appearance, good gloss retention, resistance to corrosion and excellent adhesion to a wide range of substrates like plastic, wood, metal, composites and urban industrial floors. These are attractively priced and the main polymers to be used in the paints and coatings industry. Epoxies - The range of environment friendly and easy to use epoxies provide extensive anti-corrosive treatment of metals and allied fittings. They are two- component, high solids coating with a fast drying ability thereby also allowing a faster recoat if so desired. They can be applied as a fresh or as a maintenance coating. They can be applied by air airless spray or brush and have very good resistance to abrasion, water, chemicals and solvents. Epoxies can also be used as primers to improve paint adhesion in the auto and marine industry and where protection against rust is important especially metal cans and containers. Polyurethanes - The range of polyurethanes provide an excellent recoatability and durable finishes for most environments. They can be applied as a fresh or as a maintenance coating on Glass, Metal, Wood, Plastics and urbanindustrial floors. They can be applied on a pre-primed surface by air airless spray, brush and have very good resistance to sunlight (UV), abrasion, water, chemicals and solvents.

• Packaging Size: 1 kg
• Form: Liquid
• Volatility: 1.7 %
• Temperature: -40 to 280 Deg C
• Model No: IT-2585
• Usage: Dry film lubricant
• Packing Type: Can

• Color: Red

CHO-SHIELD primer is an air-drying liquid coating for enhancing the adhesion of CHOSHIELD 2000 series electrically conductive coatings and CHOBOND 2165 to chemically treated aluminum, and most composite surfaces. Using CHO-SHIELD 1091 primer prior to application of the CHO-SHIELD 2000 series coatings CHO-BOND 2165 sealant ensures optimal adhesion to the substrate eliminating the possibility of re-work due to adhesion issues.

We offer a full range of aqeous Coating for your requirement of paper coatings for different application.

• Coverage: 8/10 m /kg/coat

pure acrylic liquid polymer modified with auxiliary agents to improve its deep penetration characteristics and sealing properties in existent porosities of concrete, sand lime bricks, cement mortars and concrete blocks.It is used as primer sealer on friable surfaces before the application of cement based coatings, paints and renders.

DESCRIPTION Venfors Floorgloss is the revolutionary flooring concept with a technique that makes your existing or newly installed concrete floor more than just strong and hardwearing. The technique is as simple as it is ingenious. Our Heavyduty machines and diamond tools grind and polish the concrete floors to remove the surface paste and expose the stronger concrete beneath. The result of this process is a stronger, more durable, shiny and beautiful floor. Both the environment and your bottom line benefit too. The initial investment is the same, or lower, than for traditional flooring solutions, but the low maintenance cost and the longer lifespan make Venfors Floorgloss the most lucrative investment option. The life cycle cost is about 60% less than for traditional flooring solutions. And using the Twister method of cleaning, you’ll find your floor is simple, environmentally friendly and cost-effective to maintain. Venfors Floorgloss is suitable for almost all environments; from the toughest industry and warehouse to home environment. It simply is a smarter floor! USES  Retail stores• „„ Warehouses &Industrial premises. „„ Truck isles (very low vibration level). „„ Public areas like café, restaurants. „„ Home environment. BENEFITS „„ 60% lower life cycle cost than traditional flooring solutions. „„ Just as good for new installations as floor renovations. „„ Infinite lifespan with Twister maintenance. „„ Low vibration levels for vehicles. „„ Environmentally friendly solution. „„ Slip-proof, even when the floor is wet. „„ Highest level of fire safety. „„ Easy-to-clean. No tyre marks, etc.. „„ Aesthetically appealing.

Dexter impex is one stop solutions for yours complete interior & building products. With creativity and innovation, we have achieved a distinct edge in providing interior design services. We are a place,where the dreams come true of architects, interior designers, builders & developers, contractors,etc. We are indulged in providing excellent interior design service to the clients at very pocket-friendly rates. We undertake commercial,industrial & residential turn-key projects. Being a quality committed entity, we always lay special emphasis on the quality of the products and services.to assure the quality, our products are procured from the reliable vendors. With transparent deals and quality of the products and services, we have won the hearts of huge clientele based in national and international market. Last but not the least we always endeavor to maintain the firm trust of the clients.

Chembond Distribution Limited - We are a supplier of high quality range of industrial coating in India.

Interior Wall Coatings, bumper paint, coil coating, furniture paints

architectural coatings, chimney paints, chlorinated paints, Primers

aerospace coating, coating products, special coating paints