Metal Roofing Sheets Dealers in Bangalore

Steel decking of 88mm is suitable for Form-work and composite Roof Floor decking to cast 50-100mm thick (over the crest) slabs. The 88-200 profile configuration of the deck sheeting imparts high strength and stability, thereby permitting the provision of usage of relatively lighter sheeting and sheet span ability up to 3.0mtr. This results in substantial reduction in the cost of purlins. JMBS Deck sheeting is of CRCA, Galvanized sheet and pre painted galvanized steel. The capability of 88mm depth sheet for the wider spans has been tested at TOR Steel Research Center, Bangalore, and the test certificates, if required, shall be provided. The full economic benefits can be availed of our roof decking system when our system is incorporated at the design stage itself.

Trapezoidal Metal Profile sheets with strong and reliable shear bond performance which is augmented by cross embossing located in the profile. The composite floor profile offers the ultimate in the light weight steel decking which reduced concrete usage to provide a cost effective and alternative floor solution that easy to install.   Application High Rise Buildings Multiplexes / Commercial Buildings Power Plant Buildings Office Buildings Mezzanine Floors in Industrial Buildings & Warehouses Steel deck fo rmezanine floors Thickness 0.8mm/1mm/1.2mm/1.6mm/2mm Technical Specification Base Metal High tensile structural grade steel Coating Mass 120, 180 & 275 GSM Coating Standard IS : 277 Yield Strength 240 MPA Premier Coating Minimum 10 Microns Colour coating Premier 10 Microns Bottom 25 Micron Available Finish Cold Rolled (CR) l Galvanised l Both side primer coated (Galvanised) Pre coated galvanised under side giving durable and attractive appearance and minimum future maintenance. Advantages Reduced Concrete usage: Tensile steel for composite slab construction that cuts down on slab thickness and dead weight of buildings. Providing a more sustainable solution and reducing costs. No separate formwork required for slab casting. Reduces construction time. Technical department at Alfa offers comprahas sive advisory of service on design of composite flooring should quiries arise which are not cover by this literature please contact us.

Self Supported Roofing System Technology initially adapted by American Army, have a widespread demand in India for Warehouses, Manufacturing Units, Automobile service station etc. The sheets are produced and installed at site with out any supports like Trusses, Purlins or any other structural memberance.

Decking Sheets are flat surfaces or platforms capable of supporting flooring and roofing sheets and these are connected to the outer or inner part of building structure. These sheets are very helpful in reducing the concentrated loading effect of roofing on the building structures by proper distribution of load. Steel, aluminum or alloy is usually used as the base material for manufacturing these sheets. In normal roofing and flooring, decking enables to transfer of the shearing forces and help to retain the proper structure of roofing. Further, for proper roof safety against leakage, UV rays, cracking, decking is an excellent support. We offer different range of decking sheets, which includes: Features Non-Fragile Greater loading capacity Excellent design Weather proof Offers excellent insulation against electricity, heat Greater span capability Dimensional stability of these sheets are excellent Have recyclable content

Composite metal deck is a cost-effective flooring system used in multi story buildings. Floors constructed of composite metal deck ate typically designed such that the corrugated of composite metal deck are typically designed such that the corrugated metal deck will support the weight of fresh concrete and some construction loads without requiring shoring. Once the concrete gains strength, the concrete and metal deck act together as a composite member. The metal deck acts as tensile reinforcement for the slab in resistance to positive moment stresses induced by dead and live loads. Traditional design practice dictates that minimum reinforcement is required in the transverse direction to control any cracks that may occur due to temperature and shrinkage movements. This minimum requirement for reinforcing has traditionally been addressed via the use of light-gauge welded wire mesh. Decking There are many advantages to using metal decking. Versatility Steel decks complying with Specifications are available in various depths and rib spacing’s, with and without stiffening elements. With and without stiffening elements, with and without acoustical material, cellular and non-cellular, and in varying material thicknesses. This extensive choice makes steel deck applicable to a wide range of projects and structural designs. Structural Strength with Less Weight The properties of steel are used with maximum efficiency in the design and fabrication of steel decks, resulting in products with a high strength – to weight ratio. As a result, delivery, erection, and structural framing costs can be lower than with other systems. Attractive Appearance Although steel decking is primarily a structural component, it is visually attractive when left exposed in other applications. With the properly specified factory and field coatings, steel deck is easy to maintain, durable, and esthetically pleasing. All Weather Construction Steel deck can be erected in most weather conditions, eliminating the costly delays that can occur with other types of floor and roof systems, Required Fire Ratings U.L. fire resistance ratings on standard roof and floor assemblies have been obtained by the Steel Deck Institute. Individual Sugam Steel Structures having ratings on their own products. Most fire resistance requirements can be met with products manufactured by Sugam Steel Structures. Uniform Quality Through engineering and continuously refined production techniques, Sugam Steel Structures produce decks that conform to specified standards.     Proven Durability Steel deck in place and performing satisfactorily for more than a half century is indicative of the product’s durability.   Economy and Value Value is determined by combining initial costs, life – cycle costs, and overall performance. Steel deck assemblies are the best value in floor and roof designs. They combine low cost with top performance.

Bare Galvalume sheet is unique as a building material. It combines the strength of steel with the excellent corrosion protection of zinc or zincaluminum alloy coatings.

Decking Sheets, Color Coated Roofing Sheets, Purlin

Galvalume Sheets, Pre Painted Galvanized, Galvalum

Decking Sheets, Cladding Sheets, Roofing System

Decking Sheets, Roofing Panel, Galvanized Steel, Sandwich Puff Panel

Floor Decking Sheet, Ridge Ventilato

Cold Rolled Decking Sheets, Acrylic Sheet, PVC Doors, Polycarbonat

Metal Roofing System, Demolition Service, Civil Contractors, Jean

Color Coated Metal Roofing Sheets, PVC Roofing Sheet

Galvalume Roofing Sheet, Air Ducts, Exhaust Ducts, Air Vent

Metal Roofing Sheets, Metal Screw, Curve Crimping Sheet, Roofing Accessorie

Shallow Metal Roofing Profile, Gutter, Aircraft Hangar

Colour Coated Metal Roof Sheet, Puf Sandwich Panel, Puf Sandwich Wall Pane

Lexan Thermopanel Insulation Sheet, Lexan Non UV Polycarbonate Shee

Corrugated Metal Shee

Ppgl Sheet, TMT Steel, TMT Bar, Mild Steel, Mild Steel Tub

Floor Decking Sheet & Roof Covering, W Beam Crash Barrier, Road Reflecto

We are offering Karthik Roofings offers decking sheets which possesses the highest bond between concrete and the steel floor. It is produced from galvanized and colour coated steel. It acts as a positive reinforcement and a permanent form support providing saving in concrete and steel and also as a diaphragm. Available in thinner and lighter slabs and hence easy to handle and install.

Metal Roofing System, Sandston

JSW Metal Roofing Shee