Power Transformers Dealers in Bangalore

• KVA: 160 to 10000
• P.V: 11000/33000
• S.V: 433/550/660
• Vector: DYN11
• Duty: Continuous
• Winding: Copper Duty Resin casted
• Srd: 11171/IEc:60726/ANSI/NEMA

New India Electicals offers a full range of dry-type transformers built to minimize environmental contamination and fire hazards. Dry-type transformers are in frequent demand among our customers. These transformers meet strict parameters with respect to electrical system demands and functioning in areas with extreme climatic conditions. Our dry and cast transformers are virtually maintenance free and are manufactured in accordance with international standards. These Transformers are manufactured in vacuum impregnation or in vacuum pressure impregnation (VPI) technology. The application of these Transformers is unique and specific, these are installed in Commercial buildings, On Board Vessles, Malls, Large Housing Complexes and now even in Compact Substations consultants & clients prefer Cast Resin Transformers as they offer a lot of safety, compactness and a clean environment. Typically, Transformers with higher power rating are protected in enclosures and sometimes equipped with air-forced cooling too for better heat dissipation. SALIENT FEATURES Off circuit tap links + 5% in steps of 2.5%. Class F and H insulation. HV Delta connected, LV Star Connected with Dyn 11 vector group. Natural air cooling and forced air cooling. Enclosure – IP 23 to IP 33 and as per customer specifications. Painting shades as per IS and IEC standards. Cable boxes on HV and LV.

• Casting: Epoxy Resin
• Highest Current For Equipment(kV): Up to 36Kv
• Rated Insulation Level(kV): Up to 36/70/170kVp
• Rated Frequency(Hz): 50-400Hz
• No of Phases: 1-Phase or 3-Phase
• Rated Primary Voltage(V): Up to 33kV
• Rated Secondary Voltage(V): 110V/RT3,110V/3,110V(As Per Requirement)
• Accuracy Class: 0.1, 0.2, 0.5, 1, 3
• Rated Burden(VA): Up to 500VA
• Accuracy Class of Protection Core: 3P and 6P
• Number of Windings: 1-2-3-4-5
• Class of Insulation: Class B, F & H
• Voltage Factor: 1.2 Continuous/1.5 for 30 sec,1.9 for 8 hours
• Type of Earthing: One End Earthed Type(E-N) / UN Earthed Type(U-N)
• Applicable Standards: IS,IEC,ANSI,BS,etc.

Exclusively used for Indoor applications. Preferred over Oil cooled Transformers due to reduced fire hazards. Maintenance free and negligible humming noise. Special type transformers -Compact type as per customer requirement/worksite constraint. Transformer designs conform to I.S 2026 & I.S 11171.

• CAPACITY: 1KVA – 25KVA 1PH
• PRIMARY VOLTAGE: 200/220V 1PH AC
• SECONDARY VOLTAGE: : 110/230V 1PH
• SYSTEM: : Delta / Star
• RATIO: : 1:1 ‘OR’ 2:1

Our Power Transformers have the largest satisfied customer base. Dedicated to providing environment friendly quality solutions and commitment to delight customers with unique value propositions.

• Working Frequency: 50/60 Hz
• Usage: IS 2026, IEC 76, ANSI.C.57, as per customer requirement
• Class Of Insulation: Class A
• Ratings: 3 phase, upto 66 kV 20000 kVA
• Winding: Copper
• Insulating Fluid: Mineral Oil, both inhibited & uninhibited, as per IS/IEC
• Cooling: ONAN, ONAF
• Tap Changer: OCTC, OLTC, as per customer requirement

Acton Power Transformers are known for delivering excellent performance. The expert R&D team develops one of the most advanced designs to withstand short-circuit and impulse voltage tests. Features: Robust design to take care of frequent short circuits Excellent process of shrinkage and drying of coils resulting in a sturdy construction Step-up and Step-down transformers manufactured Manufactured with prime CRGO using step-lap design for low losses Various ratings type tested from NABL accredited labs

We are the perfect destination for the best quality Resin Cast Transformer in the market. These Resin Cast Transformers are made of resin cast substances that are fire and humidity resistant and non -polluting in nature. Our Polyester Resin Cast Transformer can endure higher impulse voltage and temperature making it more reliable than the usual power transformers. They are suitable for installation on high- rise building where fire safety is a concern. Features : Fire resistantHumidity resistantRust freeDurable Specifications System Voltage : Up to 11kV voltage classOther specifications available as per the requirement of the clients.

• Brand Name: New India Electricals Ltd

New india electricals ltd offers a complete range of power transformer and distribution transformer designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. We have designed and supplied a large number of transformer to various parts of the world. A very large part of our customers depend on us for these transformers to drive their processes and growth. Our range covers all major types of transformers including, oil cooled and dry type. While no two transformers are the same, most of our transformer are standard design with excellent quality inputs and specific grade of raw materials, we can also offer special made-to-order transformers that will be custom built for the application and requirement.

We possess the expertise to develop custom made Ferrite transformers as per the specific needs of our clients, all this at industry leading prices. This has by far been one of the most sought after products. Specifications Low or negligible magnetism leaks Stable performance Small rise in temperature High transmission efficiency High working voltage range Minimum power loss Types Of Ferrite Transformers RM Core Transformers Pot Core Transformers EP Core Transformers Pulse Transformers Driver Transformers SMPS Transformers

Technical specifications 1 type and make of transformer a) indooroutdoor b) type of cooling c) governing specification “sabtron” indoor onan is:2026 2 rating (continuous duty) 630 kva auto 3 winding material electrolytic copper 4 frequency 50hz 5 no. Of phases 3 6 voltage between phaseneutral 0-200-240-280-290 v 7 connections star 8 vector group yao 9 terminal arrangement 13 bushes 10 temperature rise at full load over an ambient of 45 °c a) in winding b) in oil 55 °c 50 °c 11 impedence at normal voltage ratio at 75°c 1.5% 12 no load losses at normal voltage and frequency 700 watts 13 full load losses at 75°c 2500 watts 14 weights a) transformer core b) windings(copper) c) transformer oil d) tank and fitting 410 kgs 160 kgs 430 kgs(500ltrs) 400 kgs 15 total weight 1400 kgs 16 over all dimensions in mm 1300(l) x 1350(w) x 1350(h) note: all parameters furnished are subject to tolerance of +- 10% as per is

Switched mode power supply transformers (switching-mode power supply, SMPS, or switcher) are essential components in power conversion products. We essentially understand that the quality of the transformer, in terms of its performance to specification and its longevity, is vital to the quality of the end product. Miracle Electronic’s SMPS Transformers are critically designed to achieve this objective. Miracle Electronic’s SMPS Transformers have a very high power-to-size ratio, and each segment transformer topology has a unique Vin to Vout Transfer function leading to absolute efficiency. Miracle Electronic’s Switched Mode Power Supply Transformers: Achieving minimal power wastage. All our SMPS Transformers are RoHS Compliant, High, Reach Compliant, CE and UL Marked. General Product Features & Inclusions TEX E Wires Sleeves Connectors L Clamp U Brackets Ferrite Cores Class B / F/ H insulation Product Variants available: UU Transformers EE Transformers EI Transformers Toroid Ferrite Core Transformers Pot Core Transformers 10 KHz- 200 KHz Miracle Electronics also undertakes requests for custom design and development of SMPS Transformers. Please contact our Customer Support Team for more details.

An iron-core transformer having a primary winding that is connected to an alternating-current power line and one or more secondary winding’s that provide different alternating voltage values. This is the most common type of transformer, widely used in electric power transmission and appliances to convert mains voltage to low voltage to power electronic devices. They are available in power ratings ranging from mW to MW. The insulated laminations minimizes eddy current losses in the iron core. Small appliance and electronic transformers may use a split bobbin, giving a high level of insulation between the windings. The rectangular cores are made up of stampings, often in E-I shape pairs, but other shapes are sometimes used. Shields betweeen primary and secondary may be fitted to reduce EMI (electromagnetic interference), or a screen winding is occasionally used.

In addition to the above, we have the expertise to design, manufacture, & test cast resin dry type transformers for a client's special and stringent requirements to converter, rectifier, static excitation and other special applications as well The cast resin dry type transformers are designed and tested to comply with national & international standards such as IS 11171, IEC 60726, ANSI, NEMA, and Australian Standard. Kirloskar Electric manufactures cast resin dry type transformers with technical know-how from May & Christie, Germany & Ocrev, Italy.

Cast resin transformer Design conforms to Indian International standards,Designed to withstand electrical impulses, thermal and dynamic stresses,Installation close to center of load and consumption thereby saving expensive LT cable and thus avoiding voltage drop and power loss.Vacuum impregnated and cast resin dry type distribution transformer.

• Cooling Type: Air Cooled And Oil Cooled
• Country of Origin: Made in India
• Energy Efficiency Level: 5 Star
• Phase: Three Phase
• Brand Name: Astron Electric
• Power: 25 Kva to 10 mba
• Voltage Rating: 11 kv / 433 volt
• Material: copper / aluminium

• Usage: Industrial

Miracle Electronic’s Power Transformers have been exclusively designed to to provide the highest level of safety to the operator by regulating and stepping down voltages to machine tool control devices. The inherent design of the Miracle Transformer enables control circuits to be isolated from all power and lighting circuits. This allows the flawless use of grounded or ungrounded circuits that are independent of the power or lighting grounds; thus assuring greater safety to the operator. Miracle Electronic’s Power Transformers: Keep it Safe. Our Power Transformers Are RoHS Compliant, Reach Compliant, Also Available with CE and UL Marked with request. Product Variants available: 1, 10, 20 , 25 , 50 ,100, 500 VA ,1 KVA , 5 KVA ,10 KVA Air cooled 120 /240 V 1 Phase-3 Phase 50 Hz-60 Hz I UU-2 UU Transformer Low height & Low Profile   General Product Features & Inclusions Self Lead with Teflon TEX E Wires PVC Cables Sleeves Connectors L Clamp U Brackets With CRGO core / with CRNGO / with Round cores With Cold Rolled Grain / Non Grain Oriented steel cores

• Power Rating: IP55
• Number of Phase: 3-Phase
• Cooling Type: Oil Cooled
• Winding Material: Mild Steel
• Mounting Type: Floor Mounted
• Insulation Class: A
• AMC Available: Yes
• Winding Turns: Step-Up Transformer

We manufacture M.V. Indoor Cast Resin VOLTAGE TRANSFORMER which is available in various dimensions and specifications to cater to the varied requirements of clients. These are developed using innovative techniques of production to ensure international quality standards, widely known for high efficiency, low maintenance, durability and low power consumption. These can be used in Metering& protection purposes. Our range of H.T. Indoor Resin Cast VOLTAGE TRANSFORMER includes following: System voltage: 3.3/6.6/11//22/33 KV Indoor VOLTAGE Transformer. Applications Metering & Relaying Energy meter panels or Metering cubicles Medium voltage switchgears and control panels Medium voltage vacuum circuit breaker panels M.C.C. / P.C.C. Panels

• Features: Excellent performance, Sturdy construction, High Efficiency, High Insulation value, Minimum size at high output, Very low noise field, Minimal No-load losses.
• Operating Voltage: 110 / 230 / 440 V
• Operating Frequency: 50-60 Hz
• Operating Temperature: -40 C to 125 Degree C
• Use: Mainly used for transferring energy between two or more circuits through electromagnetic induction.