Distribution Transformers Dealers in Magadi Road, Bangalore (16 products available)

Apart from online payment processing methods, we also facilitate payment through offline mediums. We follow strict quality procedures that are as per the guidelines, help us in presenting dependable and cost-effective product range. We offer high quality three phase transformer.   Additional Information : Item Code - TPT-01

Smt - our company is counted amongst the foremost manufacturers & exporters, wholesalers and suppliers of distribution transformer from india.

• Nominal AC Output Voltage Ratings: 480 VAC or 208 VAC, wye derived, 60 hertz.
• Output Impedance: 3-4 % typical.
• Harmonic K-Rating: K-4, K-7, K-13, or K-20 rated in accordance with: K = Σ Ih(pu)2 h2 2.3 Performance Specifications
• Load Regulation: Maintained within +2.5% or less of nominal, from no load to full load.
• Overload: 500% for 10 seconds, and 1,000% for one cycle.
• THD: ≤ 1% added to the output voltage waveform under a linear load.
• Harmonic Attenuation: Load generated triplen harmonics are attenuated at the primary.

We are a reputed firm engaged in offering precision-engineered Three Phase Isolation Transformer. It is a continuous duty rated, 600 volt class, convection cooled, dry type, isolation transformer to support harmonic rich non-linear loads while maintaining safe operating temperatures. This transformer includes superior transverse and common mode noise attenuation. Designed as per NEMA TP 1-2002 dry type transformer efficiency standards, our transformer is acknowledged for high performance and reliability. We provide Three Phase Isolation Transformer in variegated specifications to meet diverse applications.   Standards : The power conditioning system is designed in accordance with applicable portions of the following standards NEMA TP 1-2002 Dry Type Distribution Transformer Efficiency Standards American National Standards Institute (ANSI C57.110 & C62.41-1991) Institute of Electrical and Electronic Engineers (IEEE 519-1992) National Fire Protection Association (NFPA) 70, National Electrical Code (NEC) Federal Information Processing Standards Publication 94 (FIPS Pub 94) UL Listed to Standard 1561 C-UL listed to CSA Standard C22.2, No. 47-M90  Input Specifications : Nominal AC input voltage ratings: 600 VAC, 480 VAC, 240 VAC or 208 VAC, 3 phase for transformers below 225kVA,and 600 VAC or 480 VAC, 3 phase for transformers 225kVA and above. All are designed with sufficient margin tosustain a constant input of +10% without saturation. The nominal operating frequency: 60 hertz + 3 hertz. The power conditioning system’s primary is configured in a three phase delta. Transformers below 500kVA include full capacity taps at 2½ % increments, two (2) above and four (4) below the nominal voltage tap. 500kVA transformers include full capacity taps at 2½ % increments, one (1) above and two (2) below the nominal voltage tap. Energizing inrush current will not exceed 10 times the full load input current for ½ cycle.  Output Specifications : Output Voltage : Sinusoidal with no flat topping when high crest factor (3.0 : 1), non-linear loads are present at the output. Audible Noise Measured at 1 Meter from the Unit : ≤ 50dBA for 15 KVA to 112 KVA ≤ 55dBA for 150 KVA to 225 KVA ≤ 60dBA for 300 KVA to 500 KVA Electrostatic Shielding : Incorporates two, or an optional three, solid copper foil electrostatic shields which minimize inner winding capacitance, transients, and noise coupling between primary and secondary windings. Common Mode Noise Attenuation : 126 dB with two shields, or 146dB with optional three shields. Transverse Mode Noise Attenuation : 3 dB down at 10kHz, decaying 20 dB per decade. Efficiency : 98% typical and meets NEMA TP 1-2002 dry type transformer efficiency standards on models 15kVA and above. The power conditioning transformer is designed to achieve NEMA TP 1-2002 Table 4-2 efficiencies listed below under a K-4, K-7, or K-13 non-linear load at or between 35% to 50% load and at an operating temperature of 75 degrees C. KVA Efficiency : 15* 30 97.00% 97.50% 50 97.70% 75 98.00% 112 98.20% 150 98.30% 225 98.50% 300 98.60% 500 98.70%   *15kVA model efficiency applicable to K4 and K7 loading only.  Optional TVSS : Incorporates a fused (with front panel mounted, blown fuse lamp indicator) 3 phase, secondary connected, 6 mode spike suppression network. The TVSS is comprised of high energy metal oxide varistors with less than a 5 nanosecond response time and a maximum peak current handling capability of 40,000 amps (8x20μsec) per mode. The suppression network system will remain functional when subjected to ANSI/IEEE C62.41 Category B-3 waveforms. The spike suppression network increases the transverse mode noise attenuation to 3 dB down at 10kHz, decaying 40 dB per decade.  Main Transformer : Transformer Windings : All copper conductor construction, with separate primary and secondary, isolated windings. The transformer conforms to NEC article 250, that specifies a separately derived power source. The neutral conductor is sized for 200% of the ampacity of the phase conductor. Terminals are provided for isolated three phase output conductors, neutral conductor and ground. All leads, wires and terminals are labeled to correspond with the circuit wiring diagram. Basic Impulse level : No less than 10,000 Volts. MTBF : ≥ 200,000 hours. Transformer Steel : Grain oriented, M6 grade, silicon steel. Flux Density : ≤ 15k gauss. Core Losses :  ≤ 0.6% of the KVA rating. Insulation : Class N, 200OC with a maximum temperature rise of 115OC above ambient, not exceeding 130OC under nonlinear loading per UL 1561. Cooling : Natural convection.  Cabinet : Enclosure : NEMA type 2 general purpose, floor mounted, and indoor enclosure. Construction : Cabinets are manufactured from 14 gauge steel with base sub-structure suitable for fork lifting.

A distribution transformer is a transformer that provides the final voltage transformation in the electric power distribution system, stepping down the voltage used in the distribution lines to the level used by the customer. The invention of a practical efficient transformer made AC power distribution feasible; a system using distribution transformers was demonstrated as early as 1882. If mounted on a utility pole, they are called pole-mount transformers. If the distribution lines are located at ground level or underground, distribution transformers are mounted on concrete pads and locked in steel cases, thus known as pad-mount transformers. Distribution transformers normally have ratings up to 200 KVA, although some national standards can describe units up to 5000 KVA as distribution transformers. Since distribution transformers are energized for 24 hours a day (even when they don’t carry any load), reducing iron losses has an important role in their design. As they usually don’t operate at full load, they are designed to have maximum efficiency at lower loads. To have a better efficiency, voltage regulation in these transformers should be kept to a minimum. Hence they are designed to have small leakage reactant.

2000kva11kv433v , 50hz copper wound Oil immersed Power Transformer as per Is2026.

Miracle Electronic’s Three phase transformers are used across numerous industries increasingly as a preferred to product to effectively change values of three phase voltage and current to desired units. Miracle Electronic’s Three-phase (3φ) transformers are used for efficient and fault free electrical power generation, transmission, and distribution, as well as for all industrial uses. A reliable power supply presupposes a sufficiently large supply system with high-performance transformers. The high quality standards set by MIRACLE are appreciated throughout the industry and our products ourselves stand able testimony to this claim. MMiracle Electronic’s Three Phase Transformers: Fault Free Generation, Transmission and Distribution.Miracle Electronics manufactures Power transformers up to 30 KVA in accordance with International standards and supplies to markets across the globe. All our Power Transformers are RoHS Compliant, High, Reach Compliant, CE and UL Marked with request. General Product Features & Inclusions Self-Lead TEX E Wires PVC Cables Sleeves Connectors L Clamp U Brackets Flange Type Mounting With CRGO core / with CRNGO / with Round cores Class B /F insulation Epoxy Mounting arrangements Product Variants available: 1, 10, 20 , 25 , 50 ,100, 500 VA ,1 KVA , 5 KVA ,10 KVA Air cooled 120 /240 V / 415 V 1 Phase – 3 Phase 50 Hz – 60 Hz Low height & Low Profile Miracle Electronics also undertakes requests for custom design and development of Three Phase Transformers.Please contact our Customer Support Team for more details.    

electric substation, cp plus camera, cp plus dvr, security cctv

Electrical Transformers, Low Voltage Transformers, High Voltage Transformers

Three Phase Transformers, Auto Transformers, CONTROL TRANSFORMERS

Power Distribution Transformer

Single Phase Pad Mounts Transformers, Single Phase Pole Mounts

converter transformer, Furnace Transformer, Large Power Transformer

power type transformer, Dry Type Transformer

Metering Cubicle

Electrical Transformer, Dc Machine, Alternator

Inverters, Servo Stabilizers, Power Supplies, Transformers