Adhesives Gum Dealers in Okhla, Delhi

(26 products available)
  • Structural Adhesives

    Structural Adhesives

    Get Price Quote

    • Brand NameCICO TILFI NSA
    • Country of OriginIndia
    • Model NumberCICO TILFI NSA
    • We are offering structural adhesives. Tile & structural adhesives cico tilfi nsa single pack tile adhesive for wall and floor. features can be used on dry as well as damp sustrates. Offers good adhesive bond strength slip -resistant high early strength non -shrinking fast curing long open time ( up to 25min) in wet state eco friendly -offers no health hazard to users. No curing is required economical usage bonding indoor ceramic, mosaic tiles to concreteplastered surfaces, floors and walls. method of applications suface must be structurally sound and free from dust, grease, oil etc about 250-300ml of water to be mixed for each kg of cico tilfi nsa. Add powder gradually to water and mix until a uniform, lump-free consistency is obtained spread out the above paste on the substrte to a uniform thickness bed of 34 mm by using a sutable notiched trowel having notching angle 45 degrees to teh surface. pack size : 20kg hdpe bags shelf life: 12 months
    ...more
  • Chemlok 205 Adhesive

    Chemlok 205 Adhesive

    Get Price Quote

    • Brand NameLord
    • Product Code205
    • Shelf LifeOne Year from Date of Shipment
    • Storage Condition21-27°C (70-80°F) in original, unopened container
    • Weight1Ltr
    • AppearanceGray Liquid
    • Solids Content by Weight, %22-26
    • Flash Point (Seta), °C (°F)14 (57)
    • SolventsMethyl Isobutyl Ketone (MIBK), Methyl Ethyl Ketone (MEK), Xylene
    • Density Kg/m 3920.0 - 970.0
    • Density (lb/gal)(7.7 - 8.1)
    • Viscosity, cps @ 25°C (77°F) (Brookfield LVT) (Spindle 2, 30 rpm)85 -165
    • LORD Chemlok® 205 adhesive is a heat-activated adhesive designed for use as a substrate primer under other Chemlok covercoat adhesives, or as a one-coat adhesive for bonding unvulcanized nitrile elastomer compounds. It is composed of a mixture of polymers, organic compounds and mineral fillers dissolved or dispersed in an organic solvent systemFeatures and Benefits Versatile – can be used as a primer under a wide variety of Chemlok covercoat adhesives such as the Chemlok 220 series, Chemlok 230 series, Chemlok 250 series or Chemlok 6000 series adhesives. Convenient – can be used as a one-coat adhesive to bond some nitrile rubber compounds to rigid substrates during vulcanization. Easy to Apply – applies easily by brush, dip, spray or roll coat methods; suitable for existing production lines. Durable – provides rubber tearing bonds and excellent environmental resistance when used  in combination with Chemlok covercoat adhesives. ApplicationSurface Preparation - Thoroughly clean metal surfaces prior to adhesive application. Remove protective oils, cutting oils and greases by solvent degreasing or alkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods. Chemical Cleaning - Chemical treatments are readily adapted to auto-mated metal treatment and adhesive application lines. Chemical treatments are also used on metal parts that would be distorted by blast cleaning or where tight tolerances must be maintained. Phos-phatizing is a commonly used chemical treatment for steel, while conversion coatings are commonly used for aluminum. Mechanical Cleaning - Grit blasting is the most widely used method of mechanical cleaning. However machining, grinding or wire brushing can be sed. Use steel grit to blast clean steel, cast iron and other ferrous metals. Use aluminum oxide, sand or other nonferrous grit to blast clean stainless steel, aluminum, brass, zinc and other nonferrous metals.   For further detailed information on surface preparation of specific substrates, refer to Chemlok Adhesives appli-cation guide. Handle clean metal surfaces with clean gloves to avoid contamination with skin oils.Apply Chemlok 205 adhesive to stainless steel, aluminum, brass or other nonferrous substrates within one-half hour after cleaning. For ferrous substrates such as steel, a longer layover can be tolerated if no rust is formed.Mixing – Thoroughly stir adhesive before use, and agitate sufficiently during use to keep dispersed solids uniformly suspended. Chemlok 205 adhesive is normally used full strength for brush, dip and roll coat applications. For spray application, dilute adhesive to a Zahn Cup #2 viscosity of 18-20 seconds. Chemlok 205 adhesive may be diluted with ketone-type solvents such as MEK and MIBK without adverse effects on handling and application. The diluent must be slowly added to the adhesive while stirring. Careful attention should be given to agitation since dilution will accelerate settling. Refer to the Chemlok Adhesives application guide for further information.Applying – Apply adhesive by brush, dip, roll coat, spray or any method that gives a uniform coating and avoids excessive runs or tears.Normally the dry film thickness of Chemlok 205 adhe-sive should be 5.1-10.2 micron (0.2-0.4 mil). When using Chemlok 205 adhesive over grit blasted substrates, when using it in conjunction with Chemlok 220 series covercoats or when using Chemlok 205 adhesive as a nitrile adhesive, apply a dry film thickness at the high end of the range. For all other applications (i.e., swaging or smooth substrates), apply Chemlok 205 adhesive at the low end of the film thickness range. Drying/Curing – Thoroughly dry parts coated with Chemlok 205 adhesive before applying the covercoat adhesive. This will take approximately 30-45 minutes at room temperature. It is best to use temperatures of 65-93°C (150-200°F) and abundant circulating air; however, forced air drying is possible at temperatures up to 149°C (300°F) for short periods of time. Maximum air flow at minimum temperatures will give the best results. After parts have dried, apply Chemlok covercoats using similar application methods.Dried films of Chemlok 205 adhesive are non-tacky; therefore, coated parts may be piled into tote pans for subsequent processing. Wear clean gloves when handling coated parts and cover the tote pans to prevent contamination by dirt, grease, oil, etc. If coated parts are properly protected, they can be stored for at least one month before applying covercoat or bonding. Chemlok 205 adhesive can be used to bond nitrile rubber by compression, transfer, injection or other molding procedures used to make bonded parts. As with other Chemlok adhesives, maximum adhesion is obtained when the rubber has completely cured. Ideal bonding conditions exist when both the adhesive and the rubber cure at the same time. To accomplish this, load the adhesive coated metal parts in the mold and quickly fill the cavity with rubber. Dry films of Chemlok 205 adhesive remain firm at molding temperatures. During transfer or injection molding operations, the adhesive shows minimal tendency to wipe or sweep. During multiple-cavity loading, the prebaking begins with the first loaded metal parts. Keep mold loading cycles to a minimum to prevent adhesive and rubber from pre-curing. However, Chemlok 205 adhesive will resist moderate prebaking times without affecting bond performance. Transfer or injection molds need properly designed runners and sprues, as well as adequate pressures. This prevents rubber pre-curing before the mold cavities are completely filled.Cleanup – Clean areas with a rag as soon as possible using MEK.Cautionary Information Before using this or any LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions. For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.
    ...more
  • Binding Adhesives

    Binding Adhesives

    Get Price Quote

    We bring you one of the finest Gelatin Adhesives; PLAKAL manufactured by a 130 year old company Fritz Hacker Gmbh, Germany. Plakal is based on renewable raw materials and jelly glued consisting primarily of protein and other quality additives giving it its required properties. The components of the formulation are virtually 100% biodegradable. No negative effects, either economic or ecological on the recycling of paper or cardboard. “ Stickies” are not formed. Why use PLAKAL? Because it is a Natural Adhesive What else!– adapted to the latest machine generations– Simple and clean application even with high work cycles– Universal application – even in extreme climatic conditions– High initial strength even before it has completely set– Even higher final strength after setting– Biodegradable and highly recyclable– zero health risks also during processing– No swelling or waving of paper– Elastic, stress-free setting– Price-performance ratio that holds its own PLAKAL can be used on :Case Makers like: Kolbus, Hauraf, Sthall.Book lines like: Kolbus, VBF, Sthall, Diamante.Box Making Machines: Emmeci, Zhengrun, Zhonke, HongmingSemi-Automatics- Fortec, Megabound, Hongming, Zhengrun
    ...more
  • Glass Mosaic Adhesive

    Glass Mosaic Adhesive

    Get Price Quote

    They are single component thin set adhesives but with high polymer modification. Most suitable for exterior and interior installation of tiles and stones on floors and walls. Most varieties of tiles and stones can be installed using Polymer modified thin set adhesives.
    ...more
  • PARQUET ADHESIVES

    PARQUET ADHESIVES

    Get Price Quote

    Forthcoming Range of McCoy Soudal Products   •  Acrylic dispersion based   •  Alcohol based •  Polyurethane based (1K & 2K) •  MS-Polymer based •  Primers, equalizers and epoxy seals      
  • Classic Col Adhesive

    Classic Col Adhesive

    93 / Kilogram

    • Packaging TypeDrum
    • Country of OriginMade in India
    • Packaging Size50 Kg
    • FormLiquid
    • Grade StandardIndustrial
    ...more
  • Technical Grade Liquid Glue

    Technical Grade Liquid Glue

    1,200 / Kilogram

    • Brand NameVINAVIL
    • ConditionNew
  • Dalton Tiles Adhesive

    Dalton Tiles Adhesive

    3 - 8 / Kilogram

    • MOQ500 Kilogram
    • Number Of FlowerTile Adhesives
    • Water demandApprox. 25%
    • DensityApprox 1.5 g/cc
    • Consumption1.2 kg/m²/mm
    • Self CuringNo additional curing is required
    • Pot LifeApprox 45 minutes
    • Bed Thickness3-4mm
    • Coverage45-55sft/20kg bag
    • Tensile Adhesion1 N/mm² after 28days
    • Time for trafficGrout after 12hr's light foot traffic after 24hr's (Depending on site condition)
    • Tile Adhesive is a polymer modified ready mix, self-curing cement-based dry-set adhesive for thin-bed wall and floor tiling. It provides a excellent bond on the any kind of cementations surfaces such as: plaster or concrete etc. Tile adhesive, can forms a barrier which is waterproof, between substrate and tile and it gives excellent properties of bonding. Their superior bond strength prevents shrinkage cracks and slippage of tiles.
    ...more
  • Silicone Adhesive

    Silicone Adhesive

    Get Price Quote

    Silicone Adhesive, Foam Sealant, Silicone Sealants Adhesive
  • Structural Adhesives

    Structural Adhesives

    Get Price Quote

    Structural Adhesives, Silicone Sealant, Wall Tile Adhesives, Tile Adhesive
  • Automobile Adhesives

    Automobile Adhesives

    Get Price Quote

    Automobile Adhesives, Household Adhesives, Construction Chemical
  • PVC Adhesive Glue

    PVC Adhesive Glue

    Get Price Quote

    PVC Adhesive Glue, Plastic Board, PVC Strip Roll
  • PVC Edge Fix Glue

    PVC Edge Fix Glue

    Get Price Quote

    PVC Edge Fix Glue, PVC Edge Band Tap
  • Furniture Adhesive

    Furniture Adhesive

    Get Price Quote

    Furniture Adhesive, Wires, PVC Conduit, LED Lights, Electric Fan
  • Liquid Nails

    Liquid Nails

    Get Price Quote

    Liquid Nails, Silicon Sealants, Adhesive Tapes, Structural Glazing Sealant
  • Cold Applied Adhesive

    Cold Applied Adhesive

    Get Price Quote

    It is a cold applied bituminous adhesive for fixing waterproofing membrane. It is manufactured from special grades of bitumen, suitably blended with other additives. It has semi-liquid consistency and is ready to use.
  • Adhesives

    Adhesives

    Get Price Quote

    Adhesives, Embroidery, Fashion Accessories, Chain, Glass Beads, Resin Bead
  • Acrylic Adhesive

    Acrylic Adhesive

    Get Price Quote

    Acrylic Adhesive, Flax Boad, Steel Letters, Letter Board, School Badge
  • Adhesives

    Adhesives

    Get Price Quote

    Adhesives, Sealant
  • Adhesives

    Adhesives

    Get Price Quote

    Adhesives, Reticulated Foams, Sealant
  • Adhesives

    Adhesives

    Get Price Quote

    Adhesives, Printing Ink
  • Pva Based Adhesives from Mccoy Soudal

    Pva Based Adhesives from Mccoy Soudal

    Get Price Quote

    Pva Based Adhesives from Mccoy Souda
  • Cold Applied Adhesive

    Cold Applied Adhesive

    Get Price Quote

    It is a cold applied bituminous adhesive for fixing waterproofing membrane. It is manufactured from special grades of bitumen, suitably blended with other additives. It has semi-liquid consistency and is ready to use. Application : . it is recommended for sticking roofing felts on metal, timber, tiles, asbestos, concrete and masonry surfaces, including roofs of trains, buses, tramcars, railway carriages, etc. . it is cold applied adhesive and does not require any torching. Therefore, it is useful for applications where use of hot bitumen torching is difficult or prohibited.
    ...more
  • ADHESIVE

    ADHESIVE

    Get Price Quote

    ADHESIV
  • Adhesives

    Adhesives

    Get Price Quote

    Adhesives, Sealant
  • Lamination Glue

    Lamination Glue

    Get Price Quote

    Lamination Glue, Protective Coatings, Cleaning Chemical
Filter by Locality
top