Laboratory Bath Dealers

Kinematic Viscometer Bath are an ideal companion In Industries of food, Automobile chemical, Petroleum, Pharma where determination of kinematic viscosity of lubricating oils, gear oils fuel, petroleum products and edible oils are concerned.

Ultrasonic bath works on the principle of Ultrasonic cavitation i.e. high frequency vibrations, generate agitation in liquid resulting into rapid formation and collapse of minute bubbles in liquid. Implosion of bubbles with high pressure on exposed surface of component dislodges and removes contamination like dirt, dust, oil, grease, chips, wax, lapping paste, carbon etc. Features Latest technology. Very simple operation. Generously dimensioned heating system for rapid heating of the liquid, thermostatically continuously variable between 20 and 80°C. Complete unit made of stainless steel, easy maintenance and drip-proof. Timer operation 1-99 min and continuous operation. Remaining cleaning time is optically displayed. Ultrasonic frequency 30 kHz. Tank contents 1.5 - 28 ltr. Digital Control of time and temperature. Longer tank life. Low noise level. Suitable for continuous operation. Rugged and easy to clean stainless steel housing. Fully transistorized generator. Automatic frequency tuning for maximum output. Maintenance-free.   Applications: Jewellery Optics Industry Laboratory Dental and Surgical Industry Automobile Industry Electronics Industry And many others..

Serological Water Bath is a Double walled system that is manufactured using M.S. sheet duly painted stainless steel. Its inner chamber is made from stainless steel 304 grade sheet. The Serological Water Bath that we offer consists of 2 pilot lamps and on-off switch. It is provided with immersion heater for heating. The temperature of our Serological Water Bath is controlled by thermostat. It comes with the accuracy of ± 2ºC. Available working size : 300X255X175 mm 300X300X200 mm 300X300X300 mm450X300X200 mm Optional : Low Water level cutoff deviceStirrer Digital temperature controller with an accuracy of ± 1oCMicroprocessor based P.I.D. Controller with an accuracy of ± 0.5oC

Rectangular water bath double walled construction, inner reservoir of stainless steel. Outer body in mild steel with glass wool insulation in between, supplied with lid having one hole of 12.5cms dia & 6 holes of 7.5 cms dia. Concentric rings with lids are provided on holes. The top plate & concentric rings are of stainless steel temperature range ambient to 100° C. Controlled by capillary thermostat. Size of the chamber 30cm x 25cm x 12cm.These water baths are useful for laboratory work. Thermometers at extra cost suitable for: 230 V A.C. Single Phase. Note: 9 and 12 Holes Water Bath also available.

Double walled, inside made of stainless steel 304 grade and outside mild sheet painted with attractive stove enamel. Temperature is controlled by a hydraulic thermostat from 5ºC above ambient to 100ºC with a sensitivity of ± 0.5ºC fitted with ISI mark Tublar Element. Bath consists of 2 pilot lamps & on/off switch, to work on 220/230 Volts A.C.  

The temperature range of the water bath is from few degree C. above room temperature to 100 deg. C with an accuracy of 0.5 deg. C . This bath is suitable for the Washerman, Kolmer and Khan Test inactivation's, Paraffin Embedding and many other applications in the laboratories. The bath is constructed double walled inside, made of Stainless Steel and outside of Mild Steel Sheet duly painted with epoxy powder coated provided with 25 mm mineral wool insulation on five sides . The Temperature is controlled by Electronic Digital Temperature Controller-cum-Indicator a from few ºC above ambient to 100 deg. C sensitivity of plus minus 0.5 Heating element are made of copper Nickel plated tabular type and approximately extend the full length of the bath. Control panel is provided at lower portion of the bath consisting of two neon pilot lights which indicates control cycles as well as the mains heater switch, temperature control knob. The bath is complete with perforated and removable diffuser shelves. Stainless Steel cover, brass drain plug, cord with plug to work on 220/230 volts A.C. but without rack and thermometer. Stirrer with 1/20 H.P. High Speed motor with stainless steel stirring rod and blade provided with speed regulator. Lid of water bath is made of Stainless steel 304 quality.   Option:Microprocessed PID controller having 4 ramp & 4 soak profile having set mode, alarm parameter, configuration parameter, profile parameter, set point profile, Pv error indicator , parameter for locking etc. Alarm:It is possible to provide electronic alarm, if temperature deviates more than ± 5 °C to cost extra.. Timer:Automatic timer electronic 999 mts to extra cost.

Features: Double walled construction. Inside chamber made of Stainless Steel. Outside chamber made of mild steel sheet duly powder coated. The gap between the two walls is fitted with high-grade glass wool to minimize thermal loss. Temperature range from ambient to 50°C to 250°C + 2°C Temperature is controlled by Microprocessor Based PID Digital Temperature Indicator-cum-Controller Variable speed stirring arrangement is fitted to the unit for maintaining temperature. To work on 220/230 volts A.C. supply. (A) Chamber Size : 250 x 250 x 250 m.m.(B) Chamber Size : 300 x 300 x 250 m.m.        (c) Chamber Size : 355 x 355 x 250 m.m.          OPTIONAL ACCESSORIES Digital Temperature Indicator-cum-Controller Microprocessor Based PID Temperature Indicator cum Controller.

Water bath is a laboratory equipment made from a container filled with heated water. It is used to incubate samples in water at a constant temperature over a long period of time. Circulating water baths (also called stirrers ) are ideal for applications when temperature uniformity and consistency are critical, such as enzymatic and serologic experiments. Water is thoroughly circulated throughout the bath resulting in a more uniform temperature. We specialize in both standard and customized circulatory water bath equipments, specifically designed to meet the challenging demands of various research applications.

    Suitable for all laboratory application requiring constant temperature to high degree of accuracy ± 0.2°C or better. Temperature is controlled by PID Micro Processor controller dual display with safety alarm from 5°C above ambient to 95°C. Double walled, inside made of stainless steel 304 grade and outside mild steel sheet painted with attractive stove enamel fitted with ISI mark Tublar Elements. A Glass window is fixed on the front side. Supplied complete with stirring arrangement and Goval cover. To work on 220/230 Volts A.C.