Multitech Scientific Instruments Anand Parbat, Delhi

This is yodar type, motor driven sieve shaker for carrying out wet sieve analysis of materials. Specification : Consists of a water reservoir and a holder for sieves, which can take up to 7 sieves of 150mm or 200mm diameter. Shaker is driven by a ¼ H.P. motor through a belt drive. Shaker mechanism moves the sieves up and down in the reservoir. The reservoir has a water out-let for draining out the used water. Suitable for operation 230 V A.C. Single Phase 

Brand Name : MSI

Material : Steel

Driven Type : Electric

Condition : New

Application : Laboratory

Material : Mild Steel

Country of Origin : India

Automation Grade : Manual

Load Capacity : 140 Kg

Phase : Three Phase

Frequency : 12000 +/- 400 Vibration Per Minute.

Application : Preparing Of Mortar Cubes

Country of Origin : India

Standard Used : IS 1199 & BS EN 12350 The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc. Specification: The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia and 600 mm long rounded at both ends.

Driven Type : Electric

Finishing : Polished

Specification: Same as MSI 9011 but supplied with Digital Temperature Controller range ambient to 100.0 deg C accuracy ±0.2° C, least count ±0.1° C.& FHP Motor cum Stirrer. Heaters are provided according to the size of the chamber .A control panel in which the digital controller, switches for mains, FHP stirrer, regulator for the stirrer is fit is by the side. Sizes available: 18"x12"x10" inner chamber in stainless steel, outer in mild steel. Rating of heater 2000 W suitable to run on 230 V A.C. Single Phase. MSI

Material : Mild Steel

Driven Type : Electric

Shape : Rectangular

Packaging Type : Creamy

Application : Bath

Country of Origin : 220V

Number Of Flower : Water Bath

Country of Origin : India

Material : Mild Steel

Condition : New

Application : Laboratory

Number Of Flower : Universal Testing Machine

Country of Origin : India

Material : Metal

Shape : U Shape

Automatic Grade : Manual

Application : Industrial

Number Of Flower : U Shape Box Apparatus

Country of Origin : India

Availability : 800 Kg

Country of Origin : India

IS 1237, IS 1706 Specification: This is used for determination of resistance to wear for Cement & Concrete flooring tiles. Tiles specimen of size 7.06 cm x 7.06 cm is pressed face-wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding disc the second parallel side of the tile is subjected to wear for similar number of rotations. The wear of the tile is measured on a thickness gauge specifically made for the purpose. The machine consists of a disc rotating at a speed of 30 R.P.M. in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30 Kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. A Pre-set Counter automatically stops the machine after 22 revolutions. This counter is Re-adjustable. The machine works on 440 V A.C. Three Phase electrical supply. On request machine to operate on 230 V A.C. Supply can also be supplied.

Warrenty : 1year

Country of Origin : India

Number Of Flower : Tile Abrasion Testing Machine

Automatic Grade : Semi Automatic

Condition : New

Driven Type : Electric

Brand Name : MSI

Standard Used : IS 2386 (PART-1) & BS 812 Specification: Used for determining the Flakiness Index of Aggregates. It Consists of a frame with a sliding panel. The Panel has slots of Different Standard Lengths and Widths accurately Cut.

Material : Steel

Shape : Rectagular

Condition : New

Automatic Grade : Manual

Application : Measuring Material Thickness

Application : Industrial

Capacity : 500 Kg

Country of Origin : India

Material : Mild Steel

IS 516, ASTM C-29, C-31, C-57, C-138, C-192 AASHTO T-29 & T-23 Specification: This is used for compacting concrete into cube moulds. This rod is made of steel it is 16 mm dia., 600 mm in length and rounded at both ends.

Material : Metal

Number Of Flower : Metal Rods

Country of Origin : India

For determining stripping value of bituminous mixes having aggregate size: 1.0mm to 75 micron. Specification: A circular tray rotates in a vertical plane at a rate of approximately 100 R.P.M. by an electrical geared motor. 4 bottles of approximately 400 cc are mounted on this circular tray at an angle of 900. To each other with their mouth towards center of the tray. A time switch is provided. Suitable for operation on 230 V A.C. Single Phase

Brand Name : MSI

Material : Mild Steel

A straight edge approximately 3 meters in length may be used to determine lateral surface regularity of a road surface. This lightweight apparatus is made up of mild steel or aluminum as per customers requirement and is equally supported at both ends producing a set height between the road surface & the beam. Any vertical irregularity is measured using incremented wedges. 

Material : Steel

Finishing : Polished

Condition : New

Feature : Fine Finished, Good Quality

For reaching greater depths and to facilitate easy and constant rate of penetration of the cone, this engine-driven Static Cone Penetrometer of 100 kN (10,000 kgf) capacity is preferable. The equipment consists of a hydraulic pump driven by a Diesel Engine. The whole system is mounted on a towable trolley fitted with pneumatic wheels. The pumping unit and ram are connected by means of flexible pipes through a direction control valve. The hydraulic ram moves on a two-pillar stand mounted on a trolley. Complete with the following:  Penetration Cone steel, 60° cone angle, 10 cm2 base area, with Friction Jacket    -    One Mantle Tube, 36 mm uniform OD with Sounding Rod , length 1 m    -    15 Load Measuring Head with Automatic Cut-off Valve, Pressure Gauges and Oil Can    -    One Pressure Gauge 0-600 x 5 kg/cm2    -    One Pressure Gauge 0-100 x 1 kg/cm2    -    One Screw Anchors (45 cm)   -   Six Screw Anchors (30 cm)    -    Six Screw Anchors (20 cm)    -    Six Screw Anchors Rods with cone    -    Six Driving handle for Screw Anchors    -    One Extension Pipe for Handle    -    Four  Clamping Screw with Nuts    -    Six 

casing material : Mild-steel

Automation Grade : Digital

Electrical Heating with Immersion Heating Elements and Dimmer stat for controlling the temperature. Suitable for operation on 230 V, 50Hz, Single Phase , A.C. supply. Supplied complete with 10mm cup and valve.

Material : Metal

Finishing : Polished

Condition : New

Power Source : Electric

Country of Origin : India

Shape : Square

Material : FRP

Standard Used : IS 2386 (PART III) & BS 812 The buoyancy balance system consists of a rigid support frame, incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance. The balance supplied may also be used as a standard weighing device, thus providing a versatile and comprehensive weighing system in the laboratory Specification: The outfit comprises of Electronic balance, capacity 10 kg. Least Count 0.1gm, provision is made in this balance to suspend density basket under material pan. This balance is mounted on an angle iron frame stand. Density basket. Air tight container to suspend density basket. GI Tray of area not less than 650 cm sq. Absorbent cloths 75cm x 45cm. 

Application : Industrial, Laboratory

Certification : CE Certified

Feature : Easy To Use, High Accuracy

Our semi automatic compression test machine is available from 100 Kn to 3000 KN Load frame frame can be supplied, in Chanel type, 4 pillar type, Plate type Provided with software. speed controlled by control know/simulator. power required 440V, AC supply, 50 Hz  

Feature : Digital Load Monitor,Adjustable Control Settings,Separate Control Unit

Model Number : NS-CT04B

Material : Stainless Steel

Capacity : 2000kN

Driven Type : Hydraulic

Automatic Grade : Automatic

Form professional looking tapered holes in concrete to receive posts for railings, awnings, and other common uses. Simple installation. Easy to strip/remove - just pull tab. Holes can receive square posts up to 2” or 2” pipe (2 3/8” OD) Accurate alignment - tip of tab is centerline of hole form Use with any concrete thickness Pre-install for slabs up to 6” thick High visibility Safe to use - no sharp edges Model Rail Diameter Box Qty. MSI 8002-A Up to 2-3/8" OD 25

Material : FRP

Country of Origin : India

Number Of Flower : Revolving

Standard Rockwell / Brinell Machine The Hardness Testers have been designed and manufactured strictly conforming to IS. BS, ASTM, ISO and DIN Standards. Since 1966 for most exacting test requirements in the Laboratories and Workshops etc. These testers are designed and manufactured for measuring hardness of metals and alloys of all types, hard or soft, flat, round, tubular or irregular in shape. The testers are simple in design, easy to operate, yet very reliable and accurate. Standard Rockwell Method-Manual Operation MSI 7003A: With automatic zero setting dial guage and manual load selection. MSI 7003B: With automatic zero setting dial guage and Automatic load selection Standard Rockwell/Brinell Method-Manual Operation MSI 7003C: With automatic zero setting dial gauge device and automatic toad selection. Brinell Hardness Testing facility according to 30 F/D² ratio, with 187.5 kgf load and 2.5 mm dia ball indenter. MSI7003D: Similar to MSI 7003C, but with additional test Ioad of 250 kgf and 5 mm dia ball indenter for, testing Brinell hardness of non-ferrous metals according to 10F/D ratio.

Material : Mild Steel

Finishing : Powder Coated

Driven Type : Electric

Operating Type : Semi Automatic

Usage : Hardness Testing

Display Type : Analog

Specialities : Easy To Use, High Strength

Number Of Flower : Rockwell Hardness Tester

Structure : Vertical

Country of Origin : India

Material : PVC

Shape : Conical

Feature : Durable, FIne Finhed, Perfect Shape

Number Of Flower : Pvc Traffic Cone

Country of Origin : India

Survey Prism Poles, which we offer, are appreciated for their sturdy make. These Survey Prism Poles can be assembled in different configurations. Prisms can be mounted on the top, bottom, middle or between pole sections. These Survey Prism Poles are meant for robotic or total station applications. Features: 25.4mm tilting prism w/ 0/30mm offsets Built-in circular vial With 4 (30mm dia.) threaded pole sections 5cm stainless steel threaded point

Material : Metal

Finishing : Polished

Application : Direction Use

Feature : Flexible, Rust Proof

Number Of Flower : Prism Pole

Country of Origin : India