Orthopedic Implants Dealers

Jindal Medi Surge Angled blade plates were designed by the various angled blade plate manufacturer for the fixation of proximal and distal femoral fractures. Later osteotomy plates with different angles were introduced. All angle blade plates are of one-piece construction with a fixed angle between blade and shaft. The fixed angle makes the implant less susceptible to corrosion and increases the strength of the implant. A further benefit of the fixed angle is the possibility of accurate placement of the plate in osteotomies. Angled blade plates with 95⁰ and 130⁰ angles are mainly used for fixations of fracture. Osteotomy plates of different angles are available in sizes for both adolescents, adults, children, and infants. The blade of the plates for adults has a U-cross-section, that provides high strength with minimum bone displacement. Angle blade plates for adolescents, small adults, children, and infants have a T-shaped blade cross-section. Though sharp at the tip, the seat of the blade must be prepared with a seating chisel with the corresponding cross-section. The shaft of the plate is slightly thicker than that of the broad, straight plate and can withstand higher stresses. The dynamic compression holes are arranged in an offset mode, same as the straight broad plates. These holes accept 4.5 mm cortex screws; the round holes in some kinds of plates will accept 6.5 mm cancellous bone screws. for axial compression of fractures of the femur, it is often essential to use the articulated tension device instead of the self-compressing DCP holes. Because of its special design, the insertion of the angled blade plate requires great precision. Preoperative planning is necessary to determine the exact placement of the plate. The blade must be accurately placed in both the frontal and sagittal planes, and the shaft must line up with the axis of the femur. The anatomical landmarks must be known, and guide wires inserted for orientation at the time of surgery. Misplacement of the plate may lead to valgus, varus, or rotational deformities. All plates are available in S.S.316L, LVM & Ti. Alloy.

Stainless Steel Plates : head for 4.0mm cancellous screws, shaft for 3.5mm cortex screws.Titanium Plates : head for 4.0mm cancellous screws, shaft for 3.5mm cortex screws

  Lateral Tibial Head Buttress Plate 4.5. These plates are indicated for treating shaft fractures, metaphyseal fracture, intra-articular and periprosthetic fractures of proximal tibia. Anatomically designed plate fits over proximal tibia from lateral side. These plates are designed separately for both right and left tibia and are available in a variety of lengths. Low Contact plate design reduces the plate and bone contact, this feature reduces vascular trauma. All holes of the plate allow 4.5 mm cortical screws. No. ofHoles STAINLESS STEEL Left Right 5 165.305L 165.405R 7 165.307L 165.407R 9 165.309L 165.409R 11 165.311L 165.411R 13 165.313L 165.413R No. ofHoles TITANIUM Left Right 5 Ti-165.305L Ti-165.405R 7 Ti-165.307L Ti-165.407R 9 Ti-165.309L Ti-165.409R 11 Ti-165.311L Ti-165.411R 13 Ti-165.313L Ti-165.413R    

Our online and offline modes of payment are 100% secured and facilitate payment in cash and bank transfer. Thus, we are highly preferred by the clients. Our well-structured warehouse is properly managed and maintained by our adroit professionals. Moreover, we keep on updating the unit for better safety.   Sizes : 4 Holes, 85 mm Length 5 Holes, 101 mm 6 Holes, 117 mm 7 Holes, 133 mm 8 Holes, 149 mm 9 Holes, 165 mm 10 Holes, 181 mm

We are the first indian company who produced 1. Single lock pedicle screws 2. Lateral Mass polyaxial Pedicle Screws In India. We can make any design according to buyer s specs

We are the foremost Manufacturer and Supplier of the best quality Cancellous Screws. Cancellous Screws are made using the high-quality raw materials. Cancellous Screws are tested on various parameters before the final dispatch. Cancellous Screws are widely appreciated for their durability, stability, performance, etc. Specifications Cancellous screw 3.5mm, length 10mm to 60mmCancellous screw FT 4.0mm, length 10mm to 80mmCancellous screw ST 4.0mm, length 10mm to 80mmCancellous traction screw 6.5mm length 60mm to 135mmCancellous screw FT 4.5mm, length 20mm to 80mmCancellous screw 6.5mm � 16mm, length 25mm to 110mmCancellous screw ST 4.5mm, length 20mm to 80mmCancellous screw 6.5mm � 32mm, length 25mm to 110mmCancellous screw 6.5mm � FTmm, length 25mm to 110mm Minimum Order Quantity : 10000 pieces