Pitot Tubes Dealers

Series 40H / 42H Single-Mount Accutube   These accutubes have a probe constructed of 316LSS, with a 316LSS integral 3-valve head. Both have a single-mount support and are installed through a compression fitting and thredolet (included). The 40H and 42H are designed to mount a 2 1/8″ center-to-center DP transmitter using o-rings. 1/4″ FNPT connections are also included in the design. The 42H model incorporates and integral RTD for temperature measurements. Series 40H and 42H Accutubes are available for sizes 6″ through 42″.   Series 41H / 43H Double-Mount Accutube   These accutubes have a probe constructed of 316LSS, witha 316LSS integral 3-valve head. Both are double supported, and come with compression fitting, opposite side support, and two thredolets. The 41H and 43H are designed to mount a 2 1/8″ center-to-center DP transmitter using o-rings. 1/4″ FNPT connections are also included in the design. The 43H model incorporates an integral RTD for temperature measurements. Series 41H & 43H Accutubes are available for sizes 6″ through 72″. Meriam direct mount transmitter head Accutubes have integral 3-valve equalizing manifold for ultimate utility when used with DP and Multi-Variable Transmitters. Transmitters bolt onto the head and seal with grafoil packing rings. This option saves installation and mounting time and are ideal for plant upgrades, measurement point additions and new plant construction. For applications that require a temperature measurement, select the integral RTD option to further reduce installation time and limit the number of pipe penetrations needed

Series 160S Pitot Tubes are designed specifically for flow measurement of dirty, particulate laden air or gas streams typical in smoke stack and other environmental testing. Large 516" dia. stainless steel tubing resists plugging under harsh, sooty conditions which quickly block conventional flow sensors. Total and static pressure tubes are precisely aligned and welded together every six inches for maximum accuracy, strength and long term durability. Versatile 18" female NPT connections easily adapt to any type of pipe or tubing. A pair of 18" NPT to 316" I.D. tubing adapters is included plus a handy molded vinyl cap to protect tip when not in use. Supplied with complete instructions. Permanent Mounting (PM) models include 1 inch dia. welded stainless steel sleeve and adjustable compression fitting with 1 inch male NPT mounting threads. Adjust depth, lock in place

Pitot tubes, Straight type pitot tube is widely used for dirty liquids .We also send pitot tubes for calibration at IIT powai on chargeable basis to find their co-efficient, Some of the places where pitot tubes are widely used are pitot tube for air sampler & chromatography, velocity measuring, dirty, cement plant & air blower pitot tube. Pitot tube manometers are used for velocity measurement in wind tunnel . Pitot tubes can also be used with digital manometers and anemometers. Curved joint and ellipsoidal nose are used for clear AirGas velocity measurement. Standard : • MOC-304 S.S. • Pipe -O.D. 38", I.D. 14" • Pressure Connections 14" BSP (Female) or as required • Process connection nil • Other required length, M.O.C., O.D. & I.D. Pipe, pressure connections can be provided

Unique profile shape enables high flow rate turn down, Dual averaging for better accuracy, Suitable for Liquid, gas and steam flow measurement, Repeatability of measurement ± 0.1 %, Short upstream and downstream straight pipe lengths,Long term accuracy unaffected by wear. Averaging pitot tubes are generally used for large line sizes or ducts where other primary devices become relatively expensive. Averaging Pitot tube comprises of following components:

averaging pitot tube Averaging Pitot Tube is suitable for clean liquid, gas flow measurement • Accuracy ± 2 % of actual flow rate • Repeatability of measurement ± 0.2 % • Flow rate turndown typically 4:1 • Short upstream and downstream straight pipe lengths • Long term accuracy unaffected by wear • Less pressure loss

We are offering averaging pitot tubes. Averaging pitot tube is a differential pressure producer suitable for liquid, gas and steam flow measurement. It offers simple, low cost installation into pipes and ducts, and high energy savings due to its low unrecovered pressure loss. There are no moving parts or sharp edges to wear, so long term accuracy can be maintained.

Pitot Tube is standard air velocity meter. It consists of two concentric tubes. Inner one measures total pressure existing in the fluid stream, the outer measures static pressure only. When these tubes are connected to Manometers only the velocity pressure is registered. This pressure is a measure of linear velocity of gases.

Averaging Pitot Tube is suitable for clean liquid, gas flow measurement • Accuracy ± 2 % of actual flow rate • Repeatability of measurement ± 0.2 % • Flow rate turndown typically 4:1 • Short upstream and downstream straight pipe lengths • Long term accuracy unaffected by wear • Less pressure loss

S-Shape Pitot tube Recommended specifically for flow / velocity measurement of dirty, particulate laden air or gas streams. Typical in environmental testing, large I.D. (1/4"or more) tubing resists chocking under harsh, sooty conditions. Again tube can be cleaned easily by passing air or water through it. Total & static pressure tubes are precisely aligned & arc welded together at every six inch,for maximum accuracy, strength and durability. 1/4" BSP (F) connections easily adapt to any type of pipe or tubing. Permanent engraved insertion depth graduation (optional) facilitates accurate positioning. Features :a) Long lasting S.S. construction b) 1/4" BSP c) Permanently welded d) Rated for upto 815°C (1500°F) Temp.e) Required adaptors, tubing or piping can be provided.(F) pressure connections Standard :a) MOC-304 S.S.b) Pipe -O.D. 3/8", I.D. 1/4"c) Pressure Connections 1/4" BSP (Female)d) Process connection nil(e) other required length, M.O.C., O.D. & I.D. Pipe, pressure connections can be provided Optional :1) Engraved insertion depth marking2) Nozzel or other process connection adaptors3) Isolating valves4) Connecting Hose or Tubing5) D.P. Indicating Instrument 6) Any other size, material of construction or tube as per your given drawing can be made & supplied.

advanced technocracy inc. is manufacturer, exporter & supplier of pitot static tube. range of experiments pitot tube is used to find the velocity of fluid flow & set consists of a fluid flow and pitot tube placement & velocity of flow across the section can measured.

The Pitot Tube is a differential pressure producer suitable for air flow measurement. It includes multiple sensing points to measure total and static pressures. It is easy to install and cost effective. It offers simple, low cost installation into pipes and ducts, and high energy savings due to its low unrecovered pressure loss. There are no moving parts or sharp edges to wear, so long term accuracy can be maintained.It contains a rubber cap,Plastic base and two 1 meters length air tube.   Special Features : Air Flow Measurement Low Installation Costs Long Term Accuracy Minimal Unrecovered Pressure Loss Mass Flow Measurement  

Spraytech Systems manufactured Averaging Pitot Tubes are another type of differential pressure flowmeters. Averaging Pitot tubes are basically used to detect flow velocity of fluids, gasses,steam, steam water and absolutely all those medias which atmost with 3-5ppm of solids as the max size. Spraytech Systems make averaging Pitot tubes have the potential to measure two pressures at the same time,Hexagonal sensor in forged construction, enables, perfect velocity and flow distribution, no erosion on the material with media thus,With aerodynamic design, enabling, perfect pressure distribution to enable most workable solution against cavitation and flashing conditions of the liquid media and against choking of the gas vapour media,Cost effective measurement against orifice assembly, ventury and flow nozzle as the free length space involved with Spraytech Systems make, is only 2D in upstream and 1D in downstream as compared to higher lengths defined as per beta ratio in ventury, orifice and nozzle, No moving parts,Type tested to radiography level - 1

ANNUBAR - DIAMOND BAR (AVERAGING PITOT TUBE) Annubar -Diamond Bar (Averaging Pitot Tube) is an energy saving device used to measure the flow of liquids, gases & steam in pipes, stacks & rectangular ducts. It provides high, long term stability with low permanent pressure loss. The sensor is diamond shaped which controls the separation point at which the boundary layer breaks off as the flow pass through it, resulting in a stable flow coefficient & achieving good accuracy over wide range of flow.

Pitot Static Tube, Oil Hydraulic Trainer, Universal Governor Apparatu

Averaging Pitot Tube, Orifice, Gauges, Orifice Flange Assemblie

Pitot Tube, U-Tube Manometer (Acrylic / Glass Tube

Pitot Tube, Pressure Meter, Ultrasonic Flow Meter, Temprature Indicator

Pitot Tubes, Acrylic Body Rotameter, Glass Tube Rotamete