Electrical Components Dealers

The Boltless Gate End Box(GEB) is a single bolt enclosure with a chassis mounted modular construction for the active parts. The Gate End Box is an electrical flameproof panel primarily for use at or near the coalface. It can be banked on a common skid to form an energy train. Voltage : 550V 1100V Applications For Use as : Automation Panel : Drill Panel : Motor Starter : Lighting Transformer : Lighting cum Signaling Unit : Gate End Box

Tamra phosphorous copper anode with high quality plating properties, commences with supreme quality copper cathode melted with precision % of phosphorous under vigilant controlled conditions. Cast continuous rods are produced in inert atmosphere without any scope of copper's contact with air. Stage inspections are assured and monitored strictly during further process. Thus the oxygen free melt remains 0.04-0.06% consistently.   OXYGEN-FREE COPPER ANODE (OF Gr) Tamra oxygen-free copper anodes are manufactured precisely for electroplating. Its fine grain structure with high purity level and clean surface, easily dissolved The high purity level 99.99% min. with cast crystal structure results into free flowing materials. APPLICATIONS Printed Circuit Boards Rotogravure Printing Cylinders ABS Plastic Coinage Copper Bonded Earthrod Electric Connectors Decoratives Monogram Power Distribution Equipments Ammunitions Automotive Wheels

The Following items are offered by us: G.I. Pins for 11kv / 22kv / 33kv pin insulators G.I. Stay sets, Turn Buckles Bolted come along clamps. Parallel groove clamp. Strain and Cross arm straps. Ball and socket type hardware fittings. Anchor and twisted shackles. Busbar Connectors. Compression joints, repair sleeves dead end assemblies.   All fittings fro insulators are either made of forged steel or heat treated malleable cast iron. Suspension and tension clamps are made of aluminium alloy. Materials used for midspan joints, repair sleeves, dead end assemblies are extruded aluminium alloys. For ground wire accessories the steel used are of tested quality. Our ball and socket coupling are in accordance with IS:2486 Part II or IEC standard 120. All conductor and ground wire accessories are in accordance with IS:2121. 

Stakeless earth ground loop and ac leakage current clamp for fast, safe indoor/outdoor earth ground resistance and ac leakage current tests.     Features:   Test the grounding components of equipment in hard-to-reach spaces, including areas that are indoors or fully paved and do not permit driving auxiliary test stakes. Stay on line�identify ground loop resistance without the need to disconnect then reconnect the earth electrode from the system.The Fluke 1630-2 FC Stakeless Earth Ground Clamp is the kind of high-quality, rugged tool you expect from Fluke. Heavy-duty clamp jaw stays in alignment and in calibration even in every day, on-the-job industrial environments.Stakeless measurementThe 1630-2 FC clamp measures earth ground loop resistances for multi-grounded systems using the dual-clamp jaw. This test technique eliminates the dangerous and time-consuming activity of disconnecting parallel grounds, as well as the process of finding suitable locations for auxiliary test stakes. You can also perform ground tests in places that were previously difficult: inside buildings, on power pylons or anywhere you don�t have access to soil to place auxiliary test stakes.  

Emitting Electrodes, also knows as Discharge Electrodes is the heart os the ESP. These are High Voltage internal and ionizes the gases and creates the electrical field. When the voltage breaks the gas down at the surface of the electrode, it generates corona power. This leads to creation of corona tufts on the surface of the electrode. Negative polariy voltage is applied to the electrode. The electrode design depends on various factors including the process for which the ESP is installed and the properties and composition of the flue gas. Types of Emitting Electrodes: For the corona generation, initially thin and round wires were installed. In some cases, twisted, barbed or square wires were also used.Nowadays, mostly rigid support frames are used for the electrodes. Frames may consist of spiral-spring electrodes, serrated strips, or needle / spikes mounted on a support strip. Rigid type electrodes are also used in some applications, which is made from a single piece of fabricated metal. Helios manufactures and supplies Emitting / Discharge Electrodes for Electrostatic Precipitators of all designs and makes. Raw material used for the manufacturing directly impacts the life and durabity of the Electrodes. The finish of the product greatly affects the corona generation and overall performance of the ESP. As such, proper care is taken in the manufacturing of each and every Emitting Electrode as well as the packing of the finished materials. Spiral Emitting Electrodes Pipe and Spike Type Electrode Multi-peak Discharge Electrodes Straight Round Wires Twisted pairs of Wires Barbed Discharge Wires Rigid masts Rigid frames

High & Low Voltage Transformers Bushings are used for the termination of high current in distribution transformers. We are a West Bengal- based company, engaged in manufacturing and supplying High & Low Voltage Transformers Bushings. The High & Low Voltage Transformers Bushings that we offer are widely demanded for their durability, high tensile strength and excellent functionality. We deliver High & Low Voltage Transformers Bushings after testing their quality under rigorous quality checks.