Caltech Instruments Pvt. Ltd. Andheri East, Mumbai, Maharashtra

Established test method for finding the temperature and moisture content of the air prior to painting. Not sensitive to dust solvent contaminants. BS2842 Mercury Thermometers supplied as standard. Red spirit Thermometers can be supplied if required.

Caltech Engineering Services Mumbai India Wet Film Wheels are rolled via thumb wheel specially made from brass on the flat surface to measure wet film thickness of the wet painted surfaces. The wet film wheel gauge is in the form of a wheel, approximately 50mm in diameter, grooved with three disk sections. Ends sides of the disks are of the same diameter, uniformly spaced apart for gauge support, and are concentric. Centre grooved third disk is smaller, and is eccentric to them. When the wet film wheel gauge is rolled over a wet film, center eccentric disk will also roll on the surface to pick up the material only at and below the actual thickness, which permits its immediate and direct reading. These are used for accurately measuring the wet film thickness of paints, primers, inks, adhesives, gel coatings and several other products. The Wet Film Wheel has engraved scale on the side face of measuring rim. The gauge is highly accurate with disadvantage of wft range. Wet film wheel has low range of measurement; therefore it is often used while close range measurements are required.

Material : Brass

Size : 50mm In Diameter

Application : Measuring Wet Film Thickness Of Paints, Primers, Inks, Adhesives, Gel Coatings

Feature : Thumb Wheel For Rolling, Grooved With Three Disk Sections, Engraved Scale On Measuring Rim

Accuracy : Highly Accurate

simply place in the wet paint note the wet paint thickness, Allow paint to dry and retain for future ISO record or customer requirements. All gauges have Micron Thou Mil scales. It conforms to BS 3900-C5, ISO 2808-7B and ASTM D4414-A Standards. Caltech's wet film thickness gauge is designed to measure accurate liquid coating thickness in the easiest and fastest manner. It measures the thickness immediately after the coating has been applied on the material.WFT Gauge can also be used to measure powder coating thickness before it goes through curing. Wet film thickness is measured to determine the correct dry coating thickness.Wet film thickness gauges are also known as wet film gauges, notched gauges, step gauges and WFT combs.Disposable plastic wft gauge is designed for once only use, simply place in the wet paint note the wet paint thickness, Allow paint to dry and retain for future ISO record or customer requirements. All gauges have Micron Thou Mil scales as per BS 3900-C5, ISO 2808 and ASTM D4414 standards.

Number Of Flower : Gauge

Material : Plastic

Packaging : Disposable

Application : Measure Wet Paint Thickness

It conforms to BS 3900-C5, ISO 2808-7B and ASTM D4414-A Standards. Caltech's wet film thickness gauge is designed to measure accurate liquid coating thickness in the easiest and fastest manner. It measures the thickness immediately after the coating has been applied on the material.WFT Gauge can also be used to measure powder coating thickness before it goes through curing. Wet film thickness is measured to determine the correct dry coating thickness

A weld profile gauge is just the right tool for testing welding profile, matching wheel arches and body contours, or forming panels. Simply press the gauge against the piece you want to copy. Pull it away, and there's your reproduction. A Welding profile gauge or contour gauge is a tool for recording the cross-sectional shape of a surface, welding bead width, welding profile test and welding groove.

Number Of Flower : Contour Gauge

Material : Plastic

Application : Testing Welding Profile, Matching Wheel Arches, Forming Panels,Welding, Metalworking

Feature : Records Cross-sectional Shape, Welding Bead Width, Welding Groove

Size : Standard

Availability : Lightweight

Fast, accurate visual inspection of hidden areas with an almost limitless number of positions. Double ball joint links swivel mirrors for viewing to 360°. Ullman's precision engineered links are manufactured from tempered spring steel to withstand the stresses of constant repositioning, move freely, and hold desired position.

Number Of Flower : Inspection Mirror

Material : Metal,Glass, Etc

Application : Visual Inspection Of Hidden Areas

The distinctive shapes, styles and overall appearances of all Mag® flashlights, and the circumferential inscriptions extending around the heads of all Mag® flashlights are trademarks of Mag Instrument, Inc. The circumferential inscription on the head of every flashlight signifies that it is an original Mag® flashlight and part of the Mag® family of flashlights

Number Of Flower : Flashlight

Application : Welding Inspection

Fast, accurate visual inspection of hidden areas with an almost limitless number of positions. Double ball joint links swivel mirrors for viewing to 360°. Ullman's precision engineered links are manufactured from tempered spring steel to withstand the stresses of constant repositioning, move freely, and hold desired position.

Number Of Flower : Inspection Mirror

Material : Tempered Spring Steel

Application : Visual Inspection Of Hidden Areas In Welding

Feature : Double Ball Joint Links For 360° Swivel, Precision Engineered

Movement : Move Freely And Hold Desired Position

Caltech Engineering Services is recognized amidst popular Welding Inspection Kit Manufacturers & Exporters. We present different models of Welding Inspection Kit, featuring popular G.A.L. Gage gauges. Our range of Welding Inspection Kit comprises everything you need for weld inspections, in a convenient carrying case. Kit includes CAT 12 Wrap-Around Pouch Tool Kit, CAT 12 Medium Size Tool Kit, CAT 12 American Welding Society (AWS) Tool Kit and Brief Case Type Large Tool Kit/Lock & Key

Number Of Flower : Spray

Caltech Engineering Services India offers Bridge Cam Gage for measurements are possible in either inches or millimeters: Angle of Preparation, Excess Weld Metal, Depth of Undercut, Depth of Pitting, Weld Throat Size, and more.

Feature : Angle of preparation, 0° to 60° , Depth of undercut

Delivers user-friendly, performance oriented features in a sleek, tactical design and is driven by the next generation of MAG-LED® technology. Very useful inspection torch light for inspection in tool room, welding inspection tools to check weld defects, spot welding defects, or common weld defects at onshore, offshore and automobile Industry. Flashlight LED inspection torch suppliers are all over world.

A handy compilation of mathematical relationships between leg length, throats, skew angles and inspection dimensions. A must for designers and inspectors. The perfect companion to the GAL Weld Gauge.

Number Of Flower : Measuring Tool

Material : Metal

Application : Measuring Weld Dimensions

Feature : Mathematical Relationships Guide

American Welding Society Structural Welding Code D 1.1 Paragraph 9.25 Quality of Welds 9.25.1.5 “Undercut shall be no more than 010 in. (0.25 mm) deep when the weld is transverse to the primary stress in the part that is undercut.” From G.A.L. Cage, Co. WTPS. Gauge is precision made from stainless steel all marking and dimensions are chemically etched for ease and clarity when reading.

Material : Stainless Steel

Number Of Flower : Precision Measuring Tool

Application : Measuring Undercut Depth In Welding

GAL Gage Co. manufactured V-WAC™ Gage can be purchased separately or as part of a complete set of seven fillet weld gauges that determine if your welds conform to specifications. Undercut depth or crown height scale can be read to 132 inch.

Number Of Flower : Fillet Weld Gauge

Material : Metal

Packaging : Can Be Purchased Separately Or As Part Of A Set

Application : Measuring Undercut Depth Or Crown Height In Welds

The TOMKAT 2 Cable Locator is a full function industry standard pipe and cable locator, designed and manufactured by Pact Services-UK. Better in design, the TOMKAT 2 is rugged, lightweight and packed full of features including a detachable speaker that can be held close to the ear for use in noisy environments.

Number Of Flower : Pipe And Cable Locator

Material : Rugged, Lightweight

Feature : Detachable Speaker, Industry Standard Design

Usage : Locating Underground Pipes And Cables

Ultrasonic thickness gauge which also known as D Meter is suitable for non destructive testing of thickness measuremet on variety of metallic and non-metallic materials. Ultrasonic thickness gauge is operated on micro controller based principle. NDT (Non Destructive Testing) technique is simple and instant thickness measurements are possible. LCD display for quick and best rediability. Digital Ultrasonic Thickness Gauge is useful for Steel, Mild Steel, Stainless Steel, Cast Steel, Cast Iron, Aluminum, Copper, Lead, Tin, Brass etc. Ultrasonic Thickness Gauge (D Meter) is pocket sized instrument can be taken to any place like Work Shop, Off sites.Ultrasonic thickness gauge ( Pocket D Meter ) adopts the theory of sound wave to measure a wide range of material, such as metals, plastic, ceramics, composites, epoxies, glass and other ultrasonic wave well-conductive materials. Most economical price ultrasonic thickness wall thickness measurements is possible very accurately using this handheld gage.

Number Of Flower : Handheld

Material : Metallic And Non-metallic Materials

Application : Non-destructive Testing Of Thickness Measurement

Size : Pocket-sized

Feature : Simple NDT Technique, Instant Thickness Measurements, Economical Price

Thickness measurements with the instrument are extremely simple, the only control being an ON switch. Just place the probe on a suitably prepared surface using a fluid couplant and the thickness of the test-piece is presented on a four digit LCD. Instrument is pre-calibrated for steel but it can be used on a wide range of materials by applying a conversion factor to the display dreading. Conversion factors for common engineering materials are listed on the back of the instrument. A 6mm steel test piece is mounted on the fascia panel of the instrument to enable the user to check that the Prosonic is functioning correctly and also to calibrate the instrument.

Number Of Flower : Thickness Meter

Material : Metal, Plastic, Etc

Application : Measure Thickness Of Steel And Other Materials

Caltech Engineering Services offers Tooke Paint Inspection Gauge (Plastic) is a precision tool for inspection and thickness measurement (in accordance withASTM D4138) of single or multiple coats on any substrate, and for microscopic observation and measurement of substrate and film defects. The Tooke Gauge uses an illuminated 50-power microscope equipped with a “universal scope” with a measuring reticle that accommodates measurement in mils, microns, and millimeters. (Note: Each universal microscope is validated before sale against a certified gage block traceable to the National Institute of Standards & Technology (NIST).) This gauge mounts tungsten carbide cutting tips for precise incision of the work surface. Standard cutting tips are 1×, 2×, and 10×. An optional 5× tip is available. Also, a gauge can be ordered with three tips of the same size, or with a single precision-ground tip and two blanks.

Overall Dimensions : 4.5" x 3.5" x 1" 11.4cm x 8.9cm x 2.5cm

Paint thickness tester for all types of application to measure thickness of paint, epoxy, powder coating, foil film, thin panel sheets, paper, automotive, car painting booths and repair shop etc. It works on non destructive principle. Highly sutaible for automotive and car manufacturers.

Number Of Flower : Paint Thickness Tester

Application : Measure Thickness Of Paint, Epoxy, Powder Coating, Foil Film, Thin Panel Sheets, Paper,Automotive, Car Painting Booths, Repair Shop

Material : Plastic

Caltech Engineering Services India offers EC-770 Coating Thickness Gauge. Dual technology features automatic selection of magnetic induction or eddy current measurement techniques. We are largest seller of coating thickness gauge in India. Coating Thickness Meter is highly recommended for testing powder coating thickness, anodizing aluminum thickness, paint shops, anodizing thickness tester, powder coating aluminum thickess guage, powder coating equipments, powder thickness gauge, paint thickness gauge, aluminium coating processes, and hard anodizing. Coating Thickness Meter is used by leading car manufacturers. Coating Thickness meter has PC connectivity for measuring and recording data on PC. It can give min, max, avarage and stastistical data.

Feature : 128*128 dot matrix LCD display, standard menu operations; and Two measure mode: single and continuous;

Ultrasonic thickness gauge which also known as D Meter is suitable for non destructive testing of thickness measuremet on variety of metallic and non-metallic materials. Ultrasonic thickness gauge is operated on micro controller based principle. NDT (Non Destructive Testing) technique is simple and instant thickness measurements are possible. LCD display for quick and best rediability. Digital Ultrasonic Thickness Gauge is useful for Steel, Mild Steel, Stainless Steel, Cast Steel, Cast Iron, Aluminum, Copper, Lead, Tin, Brass etc. Ultrasonic Thickness Gauge (D Meter) is pocket sized instrument can be taken to any place like Work Shop, Off sites.

Number Of Flower : Ultrasonic Thickness Gauge

Material : Metallic And Non-metallic Materials

Application : Non-destructive Testing Of Thickness Measurement

Size : Pocket-sized

Caltech Engineering Services India provides testex tape. Testex Tape is popularly called as Press-O-Film. Testex Tape press-o-film provides surface profile of a basted cleaned surface. Press O Film Replia Tape can produce virtually exact replicas of the blasted surface profile, which can be measured, using a snap gauge or testex profile gauge. Testex tape offers a simple and very accurate method of measuring blasted profiles of blasted surface. We are textex tape distributors in India. Testex Tape's Press O Film consists of layer of crushable plastic microfoam coated onto a polyster film of highly uniform thickness. Supplied with burnishing tool and testex tape instructions. Low cost way for surface replication and measurement to measure profile

Number Of Flower : Surface Profile Measurement Tape

Material : Crushable Plastic Microfoam, Polyester Film

Packaging Type : Industrial Standard Packaging

Application : Measuring Blasted Surface Profiles

Feature : Provides Surface Profile Of A Blasted Cleaned Surface, Produces Exact Replicas Of The Blasted Surface Profile, Simple And Accurate Method Of Measuring Blasted Profiles

Testex Tape or Press O Film offers a simple and very accurate method of measuring blasted profiles. It can produce virtually exact replicas of the blasted surface profile, which can be measured using a snap gauge. Testex snap gauge is simple hand held operation. Place the Testex film or press o film firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the textex snap gage. Press o film snap gauge is highly useful tool for measurements and used for pipeline & coating inspection. Testex snap gauge complies with ASTM, NACE and SSPC methods of measurement.

Number Of Flower : Measurement Tool

Material : Plastic

Application : Measuring Blasted Profiles

Applications : Pipeline & Coating Inspection

Accuracy : Very Accurate

manufactures and provides a full range of corrosion testing equipments. We assist to minimize the corrosion related problems, and to qualify materials Special Design Fillet Gauge,Small Tolerance Fillet Gauge, Special Fillet Gauge, Special Undercut Gauge, End Profile Gauge, Taper Gauge

Number Of Flower : Measuring Tool

Material : Metal

Application : Measuring Taper Angles