Sensors Dealers in Nagpur

We are offering ultrasonic sensor agecho ultrasonic sensors salient features: • agecho ultrasonic sensors are available with output options such as analog current 4-20ma,analogue voltage 0-5v,onoff signal, trigger output for multi-sensor application, pulse width ,serial ttl ,serial rs 232c. • agecho sensing range: 200mm to 1000mm … up to … 6000mm. (19.7feet) (0-200mm is dead band). • agecho accuracy is 1% of the full scale. • agecho operating voltage 12v dc, with reverse polarity protection.(24v dc optional) • agecho is very useful non-contact type of sensing or presence or counting of object. Onoff type signal is also available. • agecho is self-calibrated. Microcontroller is present in each sensor. This provides direct distancedepth reading with better calibration and communication with the controller module. • agecho is very easy to install, rugged design for use in dusty and humid conditions, suitable for outdoor as well as indoor use. • agecho very useful for non-contact distancelevel measurement. The distance of the target is measured, not just its presence, but gives directly 4-20ma, serial or pulse width data proportional to the distance of the target. • agecho operating temperature 0 to 65 degree celsius. • agecho temperature compensated measurement for better accuracy (optional). • agecho unaffected by ambient light, object color or any other optical characteristic. Works with hard materials like metal sheet, plywood, or soft materials like cloth and paper, rubber etc.

Acoustic sensors for pump monitoring Even the smallest leakages on delivery valves of oscillating positive displacement pumps (e. g. piston pumps) can be detected by measuring cavitation. The acoustic diagnostic device SITRANS DA400 consists of cavitation sensors and an analyzer unit which supplies the sensors with electrical energy and detects, filters and evaluates the measured signal and outputs an alarm signal on exceeding a defined limit value.

Description 6 Zone Door Frame Metal Detector with LCD screen IP55 Standard (Weather proof, Water proof)Network connection, RS485 port can connect Max.32 unit’s gatesPinpoint accurately the location, size, and number of concealed weaponsSensitive level can be adjustable.

Motion Sensor that we offer is highly appreciated by the customers for its dimensional accuracy, high performance and durability.  We are named among the renowned Suppliers of Motion Sensor from Maharashtra, India. Our Motion Sensor is sourced from the reliable sources of the market. To ensure defect free delivery of our Motion Sensor at the customers’ end, it is stringently tested on various quality parameters before its final dispatch.

  Weft End Sensor (Bobbin Sensor) : for detecting near empty shuttle bobbin   The circular Loom used in woven sack industry has 4–8 shuttle bobbins which provides the weft tapes to circular fabric. If this tape breaks, the fabric is wasted as it contains lots of missing tapes. Our Weft Break sensor has been used widely to detect these types of breaks and avoiding the wastage of fabric.However there has been great demand for detection of near empty condition of shuttle bobbin, so that bobbin can be changed before it is completely empty. This results in zero defect fabric. Usually to achieve this all the shuttle bobbins are replaced at once, even if they are not empty. This results in lot of tape wastage on 'Not so empty bobbins'. Our bobbin sensor is designed to detect the near empty condition of bobbin. When the sensor detects the near empty condition of bobbin, the sensor stops the loom, so that only that particular bobbin can be changed. This not only results in Zero defects Fabric, but also Zero wastage on bobbins also. The bobbin sensor is a highly sophisticated and state of the art sensor to detect when shuttle bobbin nears empty condition. The sensor is based on Infra Red to detect the presence of tape on bobbin, and a powerful, fast microprocessor which calculates various timing and detects the near empty bobbin and sends the trip signal to relay PCB. The relay PCB stops the loom by opening the NC contact which is in series with Loom Stop button. As the sensing mechanism is based on infra red principal, color of shuttle bobbin tape and base color of empty bobbin may affect the performance of sensor, however sensor will work faithfully on Light color tape and all mild steel bobbins. The installation of bobbin sensor is straight forward. The distance between sensor and shuttle bobbin(with about 1 mm of tape on it) should be around 140-160. The LED on the top of of sensor provides useful information. The functions are as under.     White LED - This LED lights up when a bobbin is under the sensor and it is sensed. (When bobbin comes under sensor, this LED lights up). During normal operation when loom is running , this LED will be ON continuously indicating that all the shuttles are sensed and no shuttle is near empty. If the white LED flashes while loom is running, it indicates that one of the bobbin is not sensed or it is near empty or completely empty. In this condition a stop signal will be generated by bobbin sensor and the loom will be stopped. If this is not the case please refer to troubleshooting section. Red LED - During normal loom running condition, when white LED is ON, and if any of the bobbins is near empty condition ,this LED will be ON briefly for approximately 2 seconds and will stop the loom by giving signal to relay PCB. The loom should stop immediately after the stop signal is generated. If loom do not stop please refer to troubleshooting section.

being a respected company guided by knowledgeable executives, we are indulged in providing an enormous assortment of temperature indicator and scanner. these offered products are highly demanded. Besides this, their industry leading rates and on time delivery at the destination of our customers has earned us enormous credibility in the industry. specifications: input: any type of thermocouple, rtd or transmitter. no. Of zones / channels: user specified (standard & nos) channel selection: automatic through program. scan time: selectable. setting: thumbwheel or keypad. display: bright 1/2" led display to indicate channel no. & its temperature or lcd load control: through contractor or solid state relay other features: channel hold facility, channel skip facility, audio-visual indication in case of channel fail input power: 230 v ac +/- 10 % 50 hz. cabinet: application specific. (din or 19" euro rack)

We can be contacted for customized packaging solutions. Besides the standard packs, we can sort items in desired quantity and pack them accordingly. Our packaging is premium. Our team experts are capable of maintaining database containing complete transactions made by our customers and thus, you can trust us for the online or offline payments made.

Set pressure selectable (Mpa, psi, kgfcm2, bar) Both upper and lower limits of pressure can be set independently Panel mountable Direct mountable Both PNP & NPN versions Two outputs

The Electrical Sensors, which we supply, are known for their reliability. We provide wide range of proximity sensors based on the requirements and specifications.      

Our products are quality tested by our professionals against various parameters to render maximum client satisfaction. Moreover, we offer these products at economical prices. Features : Reasonable price Easy to install Long lasting

The Magnetic Loom Sensor is an highly sophisticated and reliable device to sense the weft breakage, empty bobbin, and uneven weft tension in Circular Loom. The sensor is heavy-duty type and suits for environmental conditions of Plastic Woven sacks Industry. The sensor works on the principle of magnetism, there by eliminating the problems like dust, ambient light, reflection of fabric which are prominent in light based sensors. The sensor is totally sealed and hence, virtually no maintenance is required in day-to day operations. The design of sensor is such that, installation is very simple and requires fitting of boom reflector assemblies (with magnets fitted in place of diamond) on boom pipe, mounting of sensor on the loom and fitting of relay card in panel. The magnets are arranged in such a way that North and South poles of the magnets comes under sensor alternately avoiding magnetization of sensor. The 3-core wire from sensor connects to relay PCB. When shuttle bobbin runs out of the tape or if the shuttle tape breaks, then magnet rotates and comes under magnetic sensor, this magnetic field is sensed by sensor, and relay is energized. The contact of the relay stops the loom and cramming is started. The sensor can be used on other types of loom also with modification in Magnet Holder. We have already developed the magnet holder for different make of loom. We can also design the magnet holder assembly for any other type of Loom. The Advantages of Sensors The shuttle bobbin can be completely utilized hence it is not necessary to put it on creel stand for further use. As smaller bobbins removed from shuttle are not loaded on creel, the creel stand can be loaded with large size bobbin and frequent stoppage to change creel bobbin is avoided. One operator can handle multiple loom as he does not have to monitor the shuttle bobbin constantly. The wastage due to tape breakage in shuttle bobbin is totally avoided, as loom stops (with cramming if enabled), immediately if tape breaks. As the Sensor is based on magnetic principle, the effect of dust and calcium carbonate is nil. The Sensor does not requires any maintenance. The efficiency of loom increases and quality of fabric is also improved as loom stops even if the shuttle tape is slightly loose. The pay back of the system is fast due to more production, improved quality, less down time of the loom and reduced wastage.