Pharmaceutical Processing Equipment Dealers in Pune

Compression Testing Machine (Electrically Operated) - Four Pillar type It is an electric cum hand operated for compression tests on concrete specimens up to 20cm dia and 30 cm in height. The machine meets the essential requirements of various Indian, British & American standards for compression tests. Loading Unit : The hydraulic jack of 2000 kN capacity is fixed to base. The upper platen has got a self aligning action and is attached to a screw which passes through the cross head and can be raised for lowered for initial clearance adjustment. The lower platen rests on the jack ram and is positioned with the help of a centering pin. Loading is accomplished by the upward movement of the lower platen.   Pumping Unit : The motorized pumping unit which is housed in an elegant console is of double plunger type and is driven by 3 phase 440 volts 50 cycles electric motor. The pumping unit is separate unit connected to the jack by means of a steel connecting tube. A junction box is suitably fixed to connect the motor to the mains through a push button starter. The pumping unit is fitted with gauges. A maximum pointer is provided to facilitate taking of the reading after failure of the specimen. The pressure gauges are fixed on the pumping unit at an angle for easy readability. The machine is fitted with a hand wheel control which enables the rate of application of load to be varied. The machine is also equipped with facilities for hand pumping in case of power failure. The electric pumping unit is fixed with a micro-switch off the motor automatically as the load on the machine approaches the rated capacity. Relays are also incorporated in the pumping unit so that in the case of break-down of power supply, the motor will stop and would not-re-start unless starting switch is operated.

We are offering compression testing machine. Compression tests are used to determine how a product or material reacts when it is compressed, squashed, crushed or flattened by measuring fundamental parameters that determine the specimen behavior under a compressive load. These include the elastic limit, which for "hookean" materials is approximately equal to the proportional limit, and also known as yield point or yield strength, young's modulus (these, although mostly associated with tensile testing, may have compressive analogs) and compressive strength.

         Compression Testing Machine incorporates design features to enables high accuracy testing with economy, speed and versatility. Loading accuracy as high as + 1%. Straining at variable speeds to suit a wide range of materials. Continous roll autographic recorder supplied as standard to enable study of the behaviors of materials. High reading accuracy due to large size and design of dial. Wide range of standard and special accessories, including load stabilizer. Large effective clearance between columns enables testing of standard specimen as well as structures. Simple controls for ease of operation. Robust straining frame of an extremely rigid construction. Safe operation ensured by means of safety devices.     Application : Compression Testing Machine is designed to test materials and other materials under compression, bending, transverse and shear loads. Hardness test on metals can also be conducted.   Principal of Operation : Operation of the machine is by hydraulic transmission of load from the test specimen to separately housed load indicator. The hydraulic system is ideal since it replaces transmission of load through levers and knife edges, which are prone to wear and damage due to shock on rupture of test pieces. Load is applied by a hydrostatically lubricated ram. Main cylinder pressure is transmitted to the cylinder of the pendulum dynamometer system housed in the control panel. The cylinder of the dynamometer is also of self-lubricating design. The piston of the dynamometer is constantly rotated to eliminate friction. The load transmitted to the cylinder of the dynamometer is transferred through a lever system to a pendulum. Displacement of the pendulum actuates the rack and pinion mechanism which operates the load indicator pointer and the autographic recorder. The deflection of the pendulum represents the absolute load applied on the test specimen.Return movement of the pendulum is effectively damped to absorb energy in the event of sudden breakage of a specimen.   Machine consists of :    Straining Unit :   This consists of a hydraulic cylinder and a table coupled with the ram of hydraulic cylinder, mounted on robust base. The cylinder and the ram are individually lapped to eliminate friction. The cross-head is connected to two screwed columns and is driven by a motor, for rapid adjustment of test height. An elongation scale with a minimum graduation of 1.0 mm, is provided to measure the deformation of the specimen.Compression, transverse, bending, shear and hardness tests are conducted between the lower cross head and the table.   Control Panel :  The control Panel consists of a power pack complete with drive motor and an oil tank, control valves a pendulum dynamometer a load indicator system and an autographic recorder.    Power Pack : The power pack generates the maximum pressure of 200 kgf/cm2. The hydraulic pump provides continuously no pulsating oil flow. Hence the load application is very smooth.    Hydraulic Controls : Hand operated wheels are used to control the flow to and from the hydraulic cylinder. The regulation of oil flow is infinitely variable. Incorporate in the hydraulic system is a regulation valve, which maintains a practically constant rate of table movement.    Load Indicator System : This system consists of a large dial and a pointer. A dummy pointer is provided to register the maximum load reached during the test. Different measuring ranges can be selected by operating the range selection knob. An overload trip switch is incorporated which automatically, cuts out the pump motor when the load range in use is exceeded.    Pendulum Dynamometer :  This unit permits selection of favorable hydraulic ratios producing relatively small frictional forces. Pressurized oil in the loading cylinder pushes up the measuring piston proportionately and actuates the special dynamometer system. The piston is constantly rotated to eliminate friction. The dynamometer system is also provided with an integral damper and ensures high reliability of operation. The load transmitted to the dynamometer is transferred through a pendulum to the load indicator.    Autographic Continuous Roll Load-Elongation Recorder : This unit is of the pen and drum type and is supplied as standard. The horizontal motion of the pen produces the load ordinate of the diagram and the drum rotation produces the extension ordinates in the ratio of either 1:5 or 1:10.A continuous roll of graph paper is stored inside the drum and is easily replaced.   Accuracy & Calibration :  AII Compression Testing Machines are closely controlled for sensitivity, accuracy and calibration during every stage of manufacture. Every machine is then calibrated over each of its measuring ranges in accordance with the procedure laid down in BS : 1610 and IS : 1828, FIE Compression Testing Machines comply with Grade "A" of BS : 1610 and class 1 of IS 1828. An accuracy of + 1.0% is guaranteed from 20% from 20% of the load range selected to full load. Below 20% of the selected range, the maximum permissible error is 0.2% of the full load reading.   Special Accessories : These include load stabilizer, Brinell test attachment, Bend Test attachment, Shear Test attachment and a wide range of accessories offered on request at additional cost.   Installation : It is recommended that machines be erected on a foundation. Details on foundation can be given on request.FIE reserves the rights of change in the above specifications due constant improvement in design. The dimensions given above are all approximate.    

CTM – Channel type, Digital + Analogue, Electrically / hand operated, double plunger pump, single pressure gauge.i) 1500 KN capacityii) 2000 KN capacityiii) 2000 KN – Plate model, Digital (Aimil type)

we are engaged in providing double cone blenders that consist of cylindrical shell rotating on a horizontal axis that is mounted on a sturdy mild steel frame. The double cone blenders are used for mixing powder and granules. The double cone blenders can withstand rotational load of the mill charged and material to be processed. The double cone blenders have openings for easy loading and discharging. The total working capacity of the mill is as per 50% of the container capacity. The double cone blenders are made from high stainless steel and two-third volume of the cone blender is filled. The powder can be loaded through a wider opening and discharged through a mucon valve or a slide valve. applications pharmaceutical industryfood industrychemical industry capacity 150 liters onwards

Dhruv Fabrotech have marked a distinct and dynamic position in the market by providing a high-quality array of Double Cone Blender. Use: • Usage: For mixing dry powder and granules Features: • Rugged design • Excellent performance • Easy to operate Specification: • Single ph 230 v AC • Compact control unit • Volume:50 lit to 360 lits • Agitation:10 to 50 rpm or more • Easy to operates

The Nauta Mixer has a conical container which houses a constant flight screw.This screw revolves on its own axis and also around the cone wall.Material of diverse shape, size and densities are homogenously mixed without any deprivation.   Application : • Dry Blending, Dry Blending with Liquid Spray. • Features: • Low Power Consumption • Short Mixing Time • Low space require • Gentle mixing action

We are renowned as the reputed Compression Testing Machine Manufacturer & Exporter from Maharashtra, India. We fabricate the range of Testing Machine in line with the specifications provided by our customers to fulfill their varied industrial requirements. We have developed a large distribution network to ensure timely delivery of Compression Testing Machine across the world.

Our customers can buy from us a wide range of Pharma Centrifuge Machine which is used segregate liquids or gas of various densities using centrifugal force. Easy to install our machines find their wide application in various industries. These machines can be availed in various technical specifications.   Specifications: Brand: Excel Material: Stainless Steel Type: Centrifuge Item: Manual Cleaning Disc Voltage: customised Voltage: design for different country Features : Corrosion-resistance Excellent performance Long service life Resistant against corrosion Highly efficient

To make our transactions secure, we allow our clients to make payment through both offline and online mediums. we are a quality-conscious firm and for maintaining product quality, we consider several measures so as to ensure that only flawless lot reaches the buyers.   Applications : Food Cosmetic Chemical Pharmaceutical   Features : Electric controls panel with cycle time Fixed baffles provided for lumps braking The product container rotates on sped 8 RPM Enclosed rigid drive with reduction gear box and motor Safety reeling provided for revolving area of product container Charging hole with hinged lid with seal for charging and cleaning Product container having discharge with butterfly valve and man hole

Model – CTM   Straining at variable speeds to suit a wide range of materials Various models - Max capacity from 500kN to 5000 kN. Wide range of standard & special accessories including load stabilizer. Loading accuracy well within ± 1 % .

We are a Manufacturer, Exporter and Supplier of Double Cone Blender from India. Our Double Cone Blender is a high performance machine, also known as versatility used for mixing dry powder and granules equally and extensively used in industries like pharmaceutical, chemical, food, and cosmetic products etc. Our Double Cone Blender is perfectly welded, ground, and polished internally (mirror finish) and externally (matt finish). Components : Cylindrical shell Two conical frustumsButterfly valve Robust stand with bearing blocks Gear box along with motorControl panel board Safety railing Specifications : Manual rotating facility along with hand wheel for inching. The same facility is provided with SS cover & limit switch in 200 Kg and above model Available with Two nos. of safety rods at backside, option for left and right hand usersOne shaft with 04 nos. of fixed buffels with mirror polished provided inside the cone Polished cone polished with matt and mirror polish externally and internally All moving parts covered with SS304 coversQuality safety guard made SS304 pipes located in front of the m/c with limit switchPanel manufactured using SS304 material, available with facility of three-phase indication .i.e. D.O.L. Tarter, Digital Timer, and Amplify MeterLeft side drive or with right side drive option as per the need Worm reduction gear for speed reduction in blender Food grade rubber gasket will be used on both ends of cone as well as in butterfly valveGeneral body made up form of SS304 and finely polished to the matt / mirror finish as per the demand of the clients in GMP Model. Safety guards and covers fabricated of SS304 in GMP ModelHand wheel is available manual tilting of cone.

Emerged as an eminent Supplier, we are well-known for dispatching the comprehensive range of Double Cone Blender. We are capable of delivering the bulk consignments of the clientele effortlessly as we have excellent storage facilities. We have segregated units in the warehouse that helps us in delivering all the products systematically.   Product Details : Long service life Low maintenance Rugged High finish Accurate dimension Very reliable

comprehensive and integrated pharmaceutical processing, packaging and inspection solutions based on your requirements.Critical Packaging materials and functional food ingredients complete