WIND TURBINE PANEL
WIND ENERGY WIND TURBINE PANEL In conclusion in LT side of wind energy all the components for controls are developed, Produced in mass & running successfully at various site Conditions in India. Control Systems Engineers has supplied Panels for 350kw 1 MW 1.25 MW 1.5 MW and battery boxes wind turbine generators.
...moreVfd Panel
VFD PANEL which is required in all the process industries & machinery Mfg.'s. Variable Frequency drive is used as energy saving device for some of the machines to save power during no load or it is used as final control element of the closed loop control application where the speed of the motor is changed to control one parameter. Some of the application is provided with manual speed control of the motors. These are the open loop control applications.
...moretransfomers
TRANSFOMERS The costliest equipment in a substation is transformer. Therefore, the protection of transformers in the substation requires most attention. There are different relays functioning based on electrical and mechanical parameters for the protection of transformer. All these relays operate to open Circuit Breakers on either side of the transformer.
...moresimulation
TEST SIMULATION Control systems has designed and supplied panels for the following:- PLC Analogue input, Output, Digital Input, Digital output testing. Voltage simulation panel for control panel testing. Computer control test panel with industrial monitor for Hub testing.
...moreSPRAY DRIERS
SPRAY DRIERS is the transformation of feed from a fluid state into a dried particulate form by spraying feed into a hot drying medium. Spray drying system consists of four process stages. Atomization of feed into a spray.
...morescada systems
SCADA SYSTEMS has worked for various projects where scada software's r required. Engineering is required to be done for the various tag's. Trends, logging, alarms, Sequencing are provided. Various hard copy records are provided after the processing of the various data's.
...morepurged panel
PURGED PANEL has supplied many pressurized Panels by purging at the Inert Gas (Nitrogen). Complete Panel is kept at positive pressure continuously by means of adjustment of the flow rates. Pressure monitoring systems are provided to cut off the power in case of loss of purge. Panels are made as per standards NFPA-496.type X purge,Y purge & Z purge Panels are provided.
...moreplc based systems
Programmable logic controller (PLC) control panels or also known as PLC Automation Panel are one of the most important and efficient kinds of control panels. Which are generally used in variety of electronic and electrical circuit fittings. PLC Control Panels we manufacture are highly capable of giving higher output at less power consumption. Integrated with solid PLC logic and flawless PLC hardware programming.
...morePLC Automation Panels
PLC AUTOMATION PANELS are provided by the Control Systems Engineers. Control Systems Engineers have developed communication software's for remote communication of the PLC Panels in various different protocols. With PLC based Panels HMIMMI are provided to provide the operator various messages and controls of the process plants touch screen MMI are provided. To effective control of the system.
...morePDB ELECTRICAL PANEL
PDB ELECTRICAL PANEL In various industries power supply distribution Panels are required to be provided. It distributes power from incomer to the various utilities. Based on the connected load the incomer rating is decided. In case of more than 1 incomer suitable bus couplers are provided with interlocks.
...moreMONITOR INSTRUMENTATION AUTOMATION PANELS
MONITOR INSTRUMENTATION AUTOMATION PANELS to log the events occurring in the process, or for the test bench applications where the results of the tests r logged. Monitor panel houses monitor, CPU, key board, speakers etc. It is manufactured in aesthetically pleasing console design. fabrication, powder coating will be the best quality. Control Systems Engineers have tried to provide the quality of the enclosures like of ready made enclosures at the competitive rates.
...moreMIMIC INSTRUMENTATION AUTOMATION PANELS
MIMIC INSTRUMENTATION AUTOMATION PANELS of the equipment Mimic Panels are provided. Mimics are made in vinylpolycarbonate with LED's. Special electronic circuits are developed by Control Systems Engineers to show the flow of the raw materialproduct. On the MMI screen dynamic mimic is provided with all the relevant process informations. This makes the operator user-friendly access.
...moremcc
MCC houses various starters for the various drives. It is mfg. In compartmentalized and non-compartmentalized constructions. CopperAluminum bus bar is provided with the Panels. In the continuous process industries down time in the starters are critical. In that case draw out type MCC is used. Same is having modules of different ratings and new modules can be plugged by removal of the exciting module.
...moreKROM SCHRODER
KROM SCHRODER The industrial kiln systems built for heavy clay production are mostly equipped with impulse control. With this type of control, the output impulse from the burner is strong enough to produce a uniform distribution of temperature in the kiln atmosphere and a good level of circulation. A pneumatic airgas ratio control system offers maximum safety thanks to air deficiency cut-out. A constant lambda value is maintained despite changing air pressures. Staged control without a pneumatic ratio control system offers the additional option of central lambda adjustment.
...moreIncinerators
INCINERATORS Waste disposal is becoming threatening problem to the Natural Environment. To protect the environment from the hazardous waste, efficient and reliable incinerating system is the only feasible solution.
...morehvac panel
HVAC PANEL is cycling or onoff control to meet part load conditions. If building only needs half the energy that the system is designed to deliver, the system runs for about ten minutes, turns off for ten minutes, and then cycles on again. As the building load increases, the system runs longer and its off period is shorter. One problem faced by this type of control is short-cycling which keeps the system operating at the inefficient condition and wears the component quickly. A furnace or air-conditioner takes several minutes before reaching "steady-state" performance. "Well," you say, "why not just lengthen the time between starts to avoid short-cycling?" This is possible but at a cost of some discomfort for short time. The longer the time between cycles, the wider the temperature swings in the space.
...moreflare systems
FLARE SYSTEMS Hazardous gases can not be disposed of in atmosphere . hence Flare system is required. Panels for the flare is available in IIAIIB or IIC Area. Manual pilot ignition panels are used for small applciaitons. Here pilot onoff status is provided and ignition is done manually.
...moreFlameproof
FLAMEPROOF various instruments, push buttons, lamps and other operating devices. All the enclosures provided are provided with certifications from CMRI BIS DGMS. Flameproof Panels used as electrical starter Panels or monitoring & controlling instrument Control Panels.
...moreFiltration Systems
FILTRATION SYSTEMS is a phenomenon by which solid particles are removed from the liquid by means of process. Level monitoring and controls are provided in the processes. Speed of the motor is adjustable via variable speed drive to change the rate of the filtration. Various tripping interlocks are provided in the Panel for tripping andor controlling the filtration process. Since pharma industry is a highly corrosive environment SS Panels are provided.
...moreEvaporators
EVAPORATORS The starting and end products are in the liquid phase and the end Product is obtained in the concentrated form. Evaporator control involves the speed control of conveyor, various interlocks for the drives and monitoring of the evaparator parameters.
...moreDrawout Panel Accessories
DrawOut Panels are a must to reduce the production downtime & improve efficiency. These DrawOut panels are designed & developed at our advanced facility as per the defined industry standards. In every modern industry, reliable electrical systems are a must to reduce the production downtime & improve efficiency. Customer will opt for drawout panel. Panel is designed to provide fool-proof control for the motors that are installed in the many process industries viz. fertilizer, petrochemical, cement, oil refineries, chemical plants, steel plants, power stations, material handling plants & other continuous process plants wherein the continuous flow of power without the slighest break is a must.
...moreDrawout Panel
DRAWOUT PANEL is designed to provide fool-proof control for the motors that are installed in the many process industries viz. fertilizer, petrochemical, cement, oil refineries, chemical plants, steel plants, power stations, material handling plants & other continuous process plants wherein the continuous flow of power without the slighest break is a must.
...moreDCS RACKS
DCS RACKS has provided Control Panels for the whole control room for DCS cabinets. DCS cabinets are provided for all the inputsoutputs. It houses 19" cardcage systems to house the cards. Processors and inputoutput modules are plugged in the cabinet. Termination points are provided in the cabinets for the field connections. The same is provided with aesthetically pleasing enclosures.
...moreControl Panel Cabinet
Delivering you the best Quality of Automation Panels such as Automation Control Panels, PLC Automation Control Panel, VFD Panels, Pressurized Panel, Mimic, Computer Panel, Monitor, Flameproof, SCADA Systems and many more… with effective & timely delivery.
...moreBe first to Rate
Rate ThisOpening Hours