Science Laboratory Equipment Dealers in Roorkee

Pumps, This unit are a self-contained recirculation type unit. All the measurements are provided to evaluate the performance of the pump. The system is closed circuit. Water supplied from centrifugal pump. Rope break dynamometer is used to measure the output of turbine. Pressure Gauge and Orificemeter are used to measure the input of turbine. The system is closed circuit. Specifications: This Pelton Turbine Test Rig 50mm size to develop 1 KW at 1000 RPM with a flow of about 450 lpm at 25 meters supply head. Supply pump set suitable for supplying water to the above turbine Monoblock Centrifugal Pump : Kirloskar Make (3 HP, 3 Phases, 440V) Pump Size : Suction size 65mm & Delivery size 50mm Pump Discharge : 420 LPM Delivery Head : 27 meter RPM : 3000 RPM Sump Tank: Fiber glass lined MS Tank to store sufficient water for independent circulation through the unit experimentation and arrange within the floor space of main unit. Capacity 300 Liter. Runner coupled to pelton wheel. Rope Bake Dynamometer is used to measure the output. Runner diameter 220mm Spring Balance 10 kg (Salter Make). Orificemeter of 32mm is used to measure the flow rate of water through pressure gauge difference. Discharge control valve, by-pass valve of 50mm (ISI mark) used to control the flow rate of water. Pressure Gauge of 4 kg/cm2 is used to measure the pressure head. Rigid MS frame work compactly fitted with all the above items as a self-sufficient package unit suitable for operation without any foundation. Starter suitable for above motor pump set mounted on the control panel board.

The most commonly used law of Thermal Radiation is the Stefan-Boltzmann low which states that the thermal radiation heat flu emitted from a block surface (one which absorbs all the incident radiation falling on it) is proportional to the fourth power of the absolute temperature of the surface and is given by the following equation. (qA) Heat flux in WMsq. = σT = eb4 Where, T is the surface temp. which emits thermal radiation in K And Stefan – Boltzmann constant, σ=5.67 x 10-8 WM sq.—K4 eb = Emissivity power of black surface. The Stefan – Boltzmann low can be derived by integrating planks law,

• Brand Name: Quality Engineering Corporation
• Place of Origin: Roorkee
• Size: 3/8 inch diameter steel ball
• Usage: Determining the temp.
• Power: Electronic

Ring and Ball Apparatus is used for determining the temperature at which a sample of bitumenous material drops when heated under prescribed conditions. It is loaded by 3/8 inch diameter steel ball. Our Ring and Ball Apparatus is supplied complete with beaker but without thermometer. We are reckoned among the reputed Manufacturers and Suppliers of Ring and Ball Apparatus from Uttarakhand, India. One can obtain Ring and Ball Apparatus at a very reasonable price.

We offer Study of Thermoluminescence of F-centers, TLX-02 in Alkali Halide Crystals. A colour centre is a lattice defect that absorbs visible light. These colour centers can be produced by heating the crystal in excess of alkali vapour or by irradiation. The colour centers formed due to trapped electrons or trapped holes can be destroyed (bleached) by illuminating with light or warming. Important information about the colour centers can be obtained from the plot of luminescence intensity vs. temperature, taken at a constant heating rate called glow curve. It may contain one or many glow peaks, depending upon whether there are one or several different kinds of traps. The experiment consists of the following: (a) Experimental set-up for creatingvThermoluminescence (1) Sample: KBr (TLS-KBr) and KCl (TLS-KCl) single crystal (2) Thermoluminescence Temperature Meter, TL-02 • Digital Thermometer with RTD sensor • Oven power supply (3) Sample holder (4) Thermoluminescence Oven (upto 423K), TLO-02 (5) Black Box, TL-BBx (b) For measurement of Luminescence Intensity (1) Photomultiplier tube 931A, TL-PMT (2) PMT Housing with biasing circuit and connecting coaxial cables, TL-PMH (3) High Voltage Power supply, EHT-11 (4) Digital Nanoammeter, DNM-121 Complete in all respect, only X-ray facilities are required to create F-centers in the crystal.

We offer pipe friction apparatus. This apparatus is used to measure darcy's friction coefficient (f) forgiven pipes. The apparatus consists of:  a centrifugal pump of 25mm x 25mm with 12 hp motor (isi make)  m.s. Sump tank 80 ltr. To collect the warer.  m.s. Measuring tank 40 ltr fitted with piezometer tube o measure the discharge. Damper is used to collect the water in m.s mesuring tank for certain time.  g.i. Pipe of internal dia 25.4mm (1") and gunmetal isi mark control valve and regulating valves are used to circulate water.  bye-pass line is also used to regulate the discharge. this apparatus consists of a three g.i. Pipe 12", 34". The pressure tapings are provided 100cm a part on each pipe. Each tapings are connected to the mercury u tube manometer to measure head difference. Hand shuts valves are provided on each pipe to open supply in the pipe. the tanks are well epoxy painted insided to prevent rust hence increase the life of tank. experimental capabilities:  to determine the loss coefficient for different type of fittings.  comparison of pressure across two different types.

Conversant with the latest technology, We feel pride in introducing ourselves as a renowned Manufacturer and Supplier of Educational Apparatus For Heat and Mass Transfer Lab. We manufacture Educational Apparatus For Heat and Mass Transfer Lab under highly controlled industrial environment. Our precision engineering techniques have enabled us in the fabrication of one of the best Educational Apparatus For Heat and Mass Transfer Lab in the country. We can provide the diffrent kind of Educational Apparatus For Heat and Mass Transfer Lab with their models:- HMT01 : Composite Wall ApparatusHMT02 : Critical Heat Flux Apparatus HMT03 : Critical Radius of Insulating MaterialHMT04 : Emissivity Measurement ApparatusHMT05 : Finned Tube Heat Exchanger HMT06 : Forced Convection ApparatusHMT07 : Heat Pipe Demonstration ApparatusHMT08 : Heat Transfer Through Composite CylinderHMT09 : Heat Transfer Through Lagged Pipe HMT10 : Natural/Free Convection ApparatusHMT11 : Parallel Flow/Counter Current Flow in a Double Pipe Heat Exchanger Apparatus HMT12 : Pin Fin in Natural and Forced Convection ApparatusHMT13 : Shell and Tube Heat Exchanger HMT14 : Stefan Boltzmann ApparatusHMT15 : Thermal Conductivity of Insulating PowderHMT16 : Thermal Conductivity of LiquidHMT17 : Thermal Conductivity of Metal RodHMT18 : Thermal Conductivity of Slab by Guarded Hot Plate MethodHMT19 : Two Phase Heat Transfer Apparatus

• Material: Mild Steel
• Usage/Application: Laboratory
• Phase: Single Phase
• Power: 1 HP
• Voltage: 240V
• Automation Type: Automatic
• Sump Tank Capacity: 80 L
• Dimension: 250 x 400 x 350 mm
• Frequency: 50 Hz
• Power Source: Electric

We offer Thermoluminescence of F-centres, in this Pure alkali halide crystals are transparent throughout the visible region of the spectrum. The crystals may be colored in a number of ways (1) by the introduction of chemical impurities (2) by introducing an excess of the metal ion (3) by X-ray, γ-ray, neutron and electron bombardment (4) by electrolysis Colour centres produced by irradiation with X-rays When a X-ray quantum passes through an ionic crystal, it will usually give rise to a fast photo-electron with an energy of the same order as that of the incident quantum. Such electrons, because of their small mass, do not have sufficient momentum to displace ions and therefore loose their energy in producing free electrons, holes, excitons and phonons. Evidently these while moving near the vacancies form trapped electrons as well as trapped holes. The trapped-electron or trapped-hole centres so formed can be destroyed (bleached) by illuminating the crystal with light of the appropriate wavelength or warming it. The experiment consists of the following Experimental set-up for creating thermoluminescence (1) Sample: KBr or KCl single crystal (2) Thermolumniscence Temperature Meter, TL-02 Digital Thermometer Oven Power Supply (3) Sample Holder (4) Thermoluniscence Oven (0-423K) (5) Black Box For measurement of luminescence intensity (1) Photomultiplier tube: 931A (2) PMT Housing with biasing circuit and coaxial cables etc. (3) High Voltage Power Supply, Model: EHT-11 Output : 0-1500V variable (1mA max.) Regulation : 0.05% Display: 3.5 digit 7-segment LED (4) Nanoammeter, Model DNM-121 Range: 100nA to 100mA full scale in 4 ranges Accuracy : 0.2%. Display: 3.5 digit 7-segment LED Complete in all respect, only X-ray facilities are required to create F-centers in the crystal.

• Voltage: 230 V
• Test section: Horizontal, externally heated
• Blower: FHP of Standard make
• Heater: Nichrome Wire
• Item Code: NIC-18
• Length: 400 mm
• Diameter: 28 mm
• Floor Area Of: 1.2 m x 0.5 m
• Number of Phase: 1 Phase
• Digital Voltmeter: 0-300 Volt
• Digital Ammeter: 0-2 Amp

educational laboratory equipment, Standard Capacitors Box (Type -1100 B)

civil lab equipment, Anemometer, Cup type Water Current Meter, Wind Vane

Heat Transfer Lab Equipment, Surveying Instruments, Concrete lab instruments

Akero Pipe Friction Apparatus

civil lab equipment, Mechanical Lab Equipment, Electronic Lab Equipment

Mechanical Equipment, Electronic Equipment, scientific instrument, Turbines

Medical Equipments

pantograph, Tangent Clinometer, optical square, Plane Table Set

Digital Frequency Counter, Analytical Balances

Civil Engineering Equipment