Single Station Hardness Tester
Get Price Quote
Standard Features : Advance Micro-controller based user-friendly state-of-the-art product design with alphanumeric keyboard.Single Station Automatic measurement of tablet parameter... Advance Micro-controller based user-friendly state-of-the-art product design with alphanumeric keyboard. Single Station Automatic measurement of tablet parameters – Diameter/Length & Hardness. Large Non-Volatile data storage memory: 99 methods, Users Result and Validation data. Automatic run can be performed continuously up to 1- 99 tablets. RUN can be re-started on power failure or on System Reset with last run parameters. Two Tier – a] ADMIN, and b] USER password protection for method editing and Validation. Validation/Calibration protocol with verification for Hardness – 3 point Load Cell calibration with Standard weights and Diameter/Length Calibration with Standard gauges. GLP complaint print reports of Results, Program methods and Validation/Calibration data with built-in Parallel port printer interface. Built in dual RS 232 C interface for data transfer for PC and Balance for Sample Tablet weight transfer. Wide Measurement Range and Units :Tablet Hardness » up to 500N; N, Kp, Kgf, Pounds or SCTablet Diameter/Length » up to 40 mm : inch or mm (60mm option available for bolus tablets). Wide Measurement Range and Units : Tablet Hardness upto 500N; N, Kp, Kgf, Pounds or SC Tablet Diameter/Length upto 40 mm: inch or mm (60mm option available for bolus tablets)
Leeb Hardness Tester
Get Price Quote
Leeb Hardness Tester NOVOTEST T-D2Leeb Hardness Tester NOVOTEST T-D2 is designed for rapid non-destructive hardness testing of various objects.Leeb Hardness Tester NOVOTEST T-D2 uses dynamic method of hardness testing – Leeb method, standardized according to ASTM A596.Leeb probe is used for measuring the hardness of non-ferrous metals, cast iron, materials with coarse-grained structure, solid products, etc.Key features: Hardness testing of standard steels and alloyed steels Hardness testing of cast iron and nonferrous metals Testing of tensile strength of carbonized steels products of pearlite class for tension Implementation of the rebound method (Leeb) Allows user to test the products with weight more than 5 kg and thickness more than 10mm without any additional actions Restrictions about the using of Leeb Hardness Tester NOVOTEST T-D2If user need test items which are weighing less than 5 kg or thinner than 10 mm, he has to lap tightly the tested product to a surface of the base plate which are weighing more than 5 kg. Advantages Wide range of hardness measurement Allows to test the products with coarse, non-uniform structure (castings, forgings) Very ease and simplicity in setup and operation Reasonable price (lower in comparison with the ultrasonic hardness tester) User can save the results of hardness measurements into the internal memory of the device and after that, transfer them to the PC. Device allows user to operate in a wide range of the temperature. Hardness tester T-D2 has a brightness high contrast display. Device also has calibration modes for hardness testing of wide range of metals and alloys.
Best Deals from Hardness Tester
Hrc Hardness Tester
Get Price Quote
1 Set(s) (MOQ)
The small HRC 3070 is a brand new Hi-Tech portable measuring device for measuring hardness of metals, in any location. This light, compact device has been developed using state-of-the-art technology, based on the proven rebound method. Great care has been taken to ensure ease of use; no switching on and off, no buttons, no wires. All you have to do is pull back, take the measurement and read the hardness value direct in HRC. The instrument turns itself on automatically upon the first test and turns itself off again after about 20 seconds. Swiss Made – The HRC 3070 is developed and produced in Switzerland. HRC 3070 has the following typical scope of application • Big, heavy workpieces or fixed equipment parts • Production line parts during the production process • Material identification at material warehouses • Measurements at hard-to-reach places Measurement prerequisites • Minimum surface diameter 10mm • Smallest measurement surface radius of curvature 30mm • Materials weighing less than 5 kg with walls are to be set on a solid support to protect from vibrations. • Materials weighing less than 2 kg have to be set on a solid support using paste adhesive Technical data • Dimensions Ø 12mm L 140mm • Weight 36 g • Measurement accuracy ± 1 HRC • Measurement range 20-70 HRC (restriction given in HRC definition) Flashing display if batteries are low Ability to test hardness of practically all metal materials • Scope of supply Instrument, 2 coin cells, carrying case • Accessories Test block, paste adhesive
Portable Hardness Tester
Get Price Quote
Above testing unit are in compliance with International standards and with rebound and ultrasonic testing principles.
microhardness tester
Get Price Quote
All the instruments offer 12 steps of test force: 1, 5, 10, 15, 25, 50, 100, 200, 300, 500, 1000, 2000 p (gf) covering the range of test forces required by the standards ASTM E-384, EN ISO 6507 and EN ISO 4545. At the touch of a button, the test force is automatically selected. The test force can also be changed by the computer when running automated measurement cycles and as a consequence allowing different test forces in the inspection.
Hardness Testers
Get Price Quote
Hardness Testers, Bluetooth
Tablet Hardness Tester
Get Price Quote
melting range apparatus, visual melting range apparatus, titrators
Micro Hardness Tester
Get Price Quote
Micro Hardness Tester, Metal Screw Closure, Air Sampling Pump
hardness tester
Get Price Quote
hardness tester, spark spectrometer
Hardness Testing Machine
Get Price Quote
universal hardness testing equipment