Ball Valves Dealers in Thane

Flush bottom ball valve is also known as bottom valve or drain valve. As the name suggest, it is widely used to flush out the liquid or slurry from the bottom of Reactors, Receivers & Huge Tanks. “IVE” is a leading flush bottom valve manufacturer. Our Flush bottom valve assures perfect drain of the liquid / slurry from the tank. The unique design of the flush bottom ball valve will prevent formation of the dead area in the valve, hence no hold up area in the tank or vessel. This is achieved as ball of the valve will comes in the level with the inlet flange.   “IVE” offers following types of Flush Bottom Ball valves: 1) Lined flush bottom ball valve 2) Actuated ball and Y typeflush bottom valve Download Cataloge/ drawing for FLUSH BOTTOM BALL VALVE FLANGED ENDS ACTUATED FLUSH BOTTOM BALL VALVE FLANGED ENDS MANUAL

Steel strong trunnion mounted Ball valves are designed and tested in accordance with API SPEC Q1 and spec 6D. The complete split body & fully welded design offers maximum protection against line pressure and thermal distortion with long life and trouble-free performance.

We have various type of level switches. Depending on the process medium (clear liquids, viscous medium, medium at high temperature, highly corrosive medium, medium containing solid or, magnetic particles etc.) and application details (cryogenic application, tank with agitator, explosive area), we advise the suitable type of level switch. For clear liquids we have magnetic float operated level switches, pp cable float level switches, conductivity level switches, vibrating fork level switches etc. For dry and free flowing powder, granules, pallets etc we have rotating paddle level switches, vibrating fork level switches, boot diaphragm level switches etc. For slurries and sticky mediums we have rf admittance level switch, low capacitance level switch, lbfs, lffs etc. For explosive areas, we have exproof level switches also.

We offer a wide range of flush bottom tank valves. These are available in opening inside tank and opening inside valve design with teflon seating and metal to metal seating. We can offer these valves with following features: Manual/Gear Operation Motorized/Pneumatic operation RTD for temperature indication Special Alloys APPLICABLE  STANDARDS FACE TO FACE - ANSI B 16.10 MFG. STD - TESTING STANDARDS -API 598

Floating Ball Valve Integral Actuator Mounting Pad, Available in Soft Seat & Metal Seat, Screwed , Socket weld , Butt weld and Double Flanged End connection, Live Loaded gland Packing.

TYPE of Valves : 2 way, 3 way, 4 way, 5 way, 1 piece, 2 piece, 3 piece Design.Quarter turn, Half turn, Full turn i.e. L Port 900, T Port ( full turn ) A Ball Valve Is A Valve With A Spherical Disc, The Part Of The Valve Which Controls The Flow Through It. The Sphere Has A Hole, Or Port, Through The Middle So That When The Port Is In Line With Both Ends Of The Valve, Flow Will Occur. When The Valve Is Closed, The Hole Is Perpendicular To The Ends Of The Valve, And Flow Is Blocked. The Handle Or Lever Will Be Inline With The Port Position Letting You "See" The Valve's Position. The Ball Valve, Along With The Butterfly Valve And Plug Valve, Are Part Of The Family Of Quarter Turn Valves. Types of ball valveThere are five general body styles of ball valves: single body, three piece body, split body, top entry, and welded. The difference is based on how the pieces of the valve—especially the casing that contains the ball itself—are manufactured and assembled. The valve operation is the same in each case. Duplex ball valveIn addition, there are different styles related to the bore of the ball mechanism itself:A full port or more commonly known full bore ball valve has an over-sized ball so that the hole in the ball is the same size as the pipeline resulting in lower friction loss. Flow is unrestricted but the valve is larger and more expensive so this is only used where free flow is required, for example in pipelines which require pigging.In reduced port or more commonly known reduced bore ball valves, flow through the valve is one pipe size smaller than the valve's pipe size resulting in flow area being smaller than pipe. As the flow discharge remains constant and is equal to area of flow (A) times velocity (V), A1V1 = A2V2 the velocity increases with reduced area of flowThree-way and four-way ball valvesSchematic 3 way ball valve: L-shaped ball right, T-shaped leftThree-way ball valves have an L- or T-shaped hole through the middle. The different combinations of flow are shown in the figure. It is easy to see that a T valve can connect any pair of ports, or all three, together, but the 45 degree position which might disconnect all three leaves no margin for error. The L valve can connect the center port to either side port, or disconnect all three, but it cannot connect the side ports together.Multi-port ball valves with 4 ways, or more, are also commercially available, the inlet way often being orthogonal to the plane of the outlets. For special applications, such as driving air-powered motors from forward to reverse, the operation is performed by rotating a single lever four-way valve. The 4-way ball valve has two L-shaped ports in the ball that do not interconnect, sometimes referred to as an "×" port.Ball valves in sizes up to 2 inch generally come in single piece, two or three piece designs. One piece ball valves are almost always reduced bore, are relatively inexpensive and generally are throw-away. Two piece ball valves are generally slightly reduced (or standard) bore, they can be either throw-away or repairable. The 3 piece design allows for the center part of the valve containing the ball, stem & seats to be easily removed from the pipeline. This facilitates efficient cleaning of deposited sediments, replacement of seats and gland packings, polishing out of small scratches on the ball, all this without removing the pipes from the valve body. The design concept of a three piece valve is for it to be repairable.....

Flush Bottom Valves are most popular in Pharma and Industries for emptying the vessel from bottom,Effective in handling Highly Dense and Viscous Fluids & Slurry,Jacketed bodies are also available to maintain the liquid in flowing stat.

90 BALL VALVES is recommended for process mediums containing abrasive particles or solids. In such conditions, valve tightness is generally a prime factor to ensure reliable and safe operation of your plant. Primarily designed for On - Off application, RK Ball Valve can be easily adapted for control action between 10° to 60° opening, Thus, the same valve can serve as a throttling control valve or a tight shut off valve.