Separating Machines Dealers in Vatva, Ahmedabad (73 products available)

Sifter Machine . It consists of circular gyratory screens used to separate solids from solids, liquids from solid and for gradation of materials. It is designed in such a way that multi plane vibration is achieved using a specially designed vibratory motor. Being precision engineered and sturdy in construction, these machines are also helpful in separating mass composition of solids, liquid from solid and for gradation of materials as per particle sizes. Manufacturer & Exporter of Vibro Sifter. Our product range also comprises of Hydro Extractor, Industrial Centrifuge and Micro Pulverizer. Features :- Easy dismantling Optimal surface finish Low power consumption NOTE : Technical details, specification & designs are subject to change without any prior notice.

Model Number : Motor HP

LGS - 24 : 0.25

LGS - 28 : 0.5

LGS - 34 : 0.5

LGS - 39 : 1.0

LGS - 48 : 1.5

The Gyratory screen incorporates the advance technology in screening machine.This machine is useful to screen the dry powder or wet medium. It is useful in solid-solid separtaion, solid classificationor solid -liquid separation. Three components of mechanical vibration like horizontal, vertical and circular give an edge over conventional screen. Gyratory motion is produced by rigid screening device that vibrates with screen above its center of mass. Machine consists of a circular table, which is an assembly of the number of decks with screens, and a spacing frames equipped with discharge spout. Screen held in uniform tension in all direction by a center support. This whole mass suspended on coil springs allow unit to vibrate freely and also give thrust to screening unit by its own compression and decompression. At the same time it also prevents transmission of vibration to the floor.Vibration is motivated by specially designed vertical vibrating motor, beneath the whole assembly and inside the rigid housing. Motor has extended shaft on both side on which eccentric weights are mounted. As shaft rotates it also rotate eccentric weights and this eccentricity gives vibration to whole unit.   Principle: Material required to be classified is charged as thin bed into the upper deck over the screen.Coarser particles remain over screen, while fines pass through the screen and enter into lower deck. Particles over each screen in each deck are discharged automatically from individual discharge spout of each deck. Rotation of top eccentric mass causes vibration in horizontal plane and if it is increased, it will increase horizontal throw on screen will cause the over size material to discharge at faster rate. The lower weight causes vibration in vertical plane and tangential plane. It is desirable to promote maximum vertical vibration in order to dislodge material and to clean the screen. The tangential component of vibration and hence circular motion of particles in the screen are controlled by the angular position of the top and bottom eccentric weights to give better screening efficiency

Protects plastics processing machine screw-barrel and die from ferrous and non-ferrous metal impurities. It can be installed directly online on processing machine or offline for batch production. Ejection of rejected impurity occurs without shearing effect. Special design for high Temp. application also available

Multiport Air Separator is very simple to use and yet it is extremely accurate in separating ?lights? from "heavies?. Traditionally, screeners are the first idea when a separation is required for any material. Actually, an air separator - aspirator - might be better suited for the job. There are times that a screen is more effective. At other times, an aspirator is more effective. For the ultimate best results, aspirators and screens can be used together ? attaining the best effects of each unit. Multiport Air Separator has a series of either 4 or 6 slides that allow the product to tumble back and forth while gravity flowing through the machine. At each pass, ambient air is drawn through the product, lifting the light weight particle into a selection chamber to determine if it ?qualifies? to be lifted out or if it should remain with the "heavies?. Those light weight particles that have been ?selected to lift?, are removed from the product stream. The product then tumbles down into the next selection chamber where all remaining particles are again exposed to the selection process. Ambient air is introduced a second time, lifting the remaining light weight particles away without over aspirating any of the heavies. This process is repeated a total of four or six times ? essentially removing all of the lightweight particles without removing any of the heavies. Six air inlets AND six air outlets ? all in one machine. Multiport Air Separator has no moving parts, no fine openings to blind or plug It can be adjusted ?on the run? with an infinite number of settings, and also transports the liftings to a destination of your choice. Multiport Air Separator has been applied on finished product to remove fines and dust (pellets, cereals, prills), during process to reduce dust (explosive fines, infestation, clean a product stream, etc.), and to make product improvements. Multiport Air Separator has been used to separate different types of plastics in ?regrind/reclaim? systems, dedust fertilizer prills, clean and upgrade grain ? removing damaged kernels and foreign material, separate hulls or shells from seeds or nuts, and many other application

Material : ALUMINUM

Brand Name : GENERAL IMSUBS

Production Capacity : 20 CFM

Model : WOMS-25

Pressure (Bar) : 10 Bar

Vibro Type Sifter available in 10", 12", 18", 20", 30" 36" & 48" Models with MOC of SS 316 for the vibratory system for the Sieving, Grading & Sizing of Granules.

compact vibratory scree design manufacturer for high speed & dust free sieving. Noiseless and maintenance free machine.   salient features:- vibro sifter machine compact vibratory screen designed powder sieving machine for high speed & dust free sieving. noiseless and maintenance free vibro screen machine. all contact parts and screen made of ss 304 (ss 316 optional) low power consumption compared to reciprocating vibratory vibro sieve system. easy dismantling and cleaning of contact parts of vibrating screen. machine available with flame proof and double / triple deck options for lab/pharmaceutical industry

Country of Origin : India

Type : Vibro Sifter

Certification : CE

Weight : 100-1000kg

Color : SS304

Voltage : 440V

Condition : New

Automatic Grade : Automatic

Power : 1-3kw

Driven Type : Electric

Warranty : 1year

3 Micron Borosilicate Glass Fiber media type Moisture Separator This unique design 3 Micron Borosilicate Glass Fiber media type Moisture Separator is very effective for removal of Moisture from compressed Air. It prevents dirt, dust & water particles to be carried into the pneumatic system. It is recommended to install this Separator just before application point for better performance.

Features Safe, Secure, leak-proof, Lightweight and easy to handle, Very high Efficiency     Non-corrosive Aluminium die cast or powder coated MS body, Compact Design, Maintenance Free, Long life     Manual drain and auto drain facility, no corrosion, reduced maintenance, Easy to alter or extend a system

Effective Separation of heavy & light material (Metal pieces, Pins, Plastics) from pulp.Easy maintenance and minimum fiber loss.The body is made out of mild steel with S.S. cladding. Special model is also available in S.S. 316 Sandwitch plate (S.S. and M.S.) with base frame and stifners in M.S.A cyclone effect is formed in the separator by the S.S. Rotor, So heavy particle are carried outward by centrifugal force to the junk trap. The light rejection is further treated in secondary separator or vibrating screen.

Material : STAINLESS STEEL

Voltage : 440 V

Material Grade : SS 316

Model Name/Number : VE-100

Usage/Application : Industrial

Automation Grade : Automatic

Phase : Single Phase

Material : SS

Capacity : 500 Kg/Hr

Electric Motor : 1 HP

Diameter : 72 Inch

Brand : Ultra Febtech

We provide a wide range of vibro shifterthat is primarily a vibrating energy screen. It consists of a circular pre-tensioned screen that is mounted along with vibrating motor on the frame. Three plane vibrations are imparted on the screen by the vibrating motor caused due to the rotatory motion of eccentric weights. This shifter is manufactured by our skilled professionals using high grade raw material in conformity with the global quality standards. Our clients can purchase this shifter from us in different. Features: Precision-designed Durability Long service life

Advanced Design especially for screw air compressor. High efficiency of separation rate up to 0.1 um. Double filtrations and Low resistance. Oil contains in the compressed air : 3 ppm.

Vibro Screens, available in size from 24”to 60”” in diameter with convenient design; maximize screen surface, provide good rate of screening, one to multilevel screens giving desired numbers of predefined portions with absolute separations in various mesh sizes. The equipment also can be supplied with dust cover and other special accessories. Material of construction will be as per requirement of customer.

This equipment are mostly used for common dust removal in industry. They are simple in construction and varieties of materials can be used and also at a very high temperature. ‘FAN-TECH’ cyclone separators that is widely demanded by our clients for their efficient performance and durability. Manufactured using high quality raw material, this cyclone separator helps in ensuring stringent particulate pollution control and material recovery. The large volume of gas makes it difficult to accomplish the desired dust collection efficiency in a single stage cyclone construction. The range of cyclone separators manufactured by us configure high efficiency cyclones into various versions, two cyclones, in order to achieve optimum efficiency. Features Required :- High separation efficiency over a broad flow rang Flow-optimized design. No Maintenance. Customized Designed for all application. Low pressure drop resulting in energy savings Applications :- General applications include Cement Ind, Foundries, Rubber, Grains, Food, Coal, Metalworking, Paper, Fly ash handling, Sugar, Plastic, Rock product, Cement Ind, Boiler Flue Gas, Chemicals and many more....

Prince industries are one of the leading manufacturer of Air classifier and also doing business worldwide. Air classifier is a machine which is separate dry materials into different particle size fractions by their size, mass or shape. Air classifier is also use for remove the fine fraction of a material or the over size or coarse particles of a material. ir classifier is is a compact and dust tight machine which is use for various powdered material. Air classifier is made with the high engineering professional who gives long durability to their customer. Air classifier is designed with low and high operating speed, which having minimal wear can use at a lower speed and high speed while using handling abrasive material.  

Model : CMSM - 30"

Screens : SS 304 (SS 316 Optional)

Screen Dia. : 750 mm

Capacity / Hour * : 30 to 300 Kgs.

Charging Height : 1050 mm without Lid

Discharding Height : 670 ± 5 mm

Electric Motor : 0.25 Hp / 1440 RPM / 3 Ph

SALIENT FEATURES: Noiseless, Maintenance free & high speed machine. Available in different models. Portable and compact. All contact parts and screen of SS 304 AISI stainless steel material. Electric power consumption is very less compared to reciprocating vibratory system. Standard machine are with TEFC motor explosion proof / flame proof motor material. SS 316 quality contact parts optional. Easy dismantling and cleaning facility for contact parts. Double & Triple deck screens with outlet and hopper for bottom deck available on request.

Material : SS

Automation Type : Automatic

Color : Silver

Phase : Single Phase

Brand Name : MPM

Shape : Round

Capacity : 20kg also available upto 400kg

Power : 2HP

  Effective Separation of heavy & light material (Metal pieces, Pins, Plastics) from pulp. Easy maintenance and minimum fiber loss. The body is made out of mild steel with S.S. cladding. Special model is also available in S.S. 316 Sandwitch plate (S.S. and M.S.) with base frame and stifners in M.S. A cyclone effect is formed in the separator by the S.S. Rotor, So heavy particle are carried outward by centrifugal force to the junk trap. The light rejection is further treated in secondary separator or vibrating screen.

Machine Size:- : Height – 1220 With Caster Wheel,Diameter Size :- 762mm Round ( 30 “ ),Net Weight – 100 KG Approx

Machine Contraction : – : S.S 304

Power Supply : – : 440v 3 Phase

Caster Wheel Size:- : 2 Inch , S.S 304

Two Way Output:- : (1 Grade, 2 Grade)

Wire Max – 22 – : 440 Volt, 3 Phase

Vibro Motor : 1 HP (1440RPM)

Application & Process : Compact Sieving & Grading Process Technic Vibro Sifter is used for screening, sieving, grading for solid-liquid separation, process to separate the desired elements and the undesired elements from the combination of solid to solid (where two solids are generally having different properties) and solid to liquid material. It used in various industries such as Pharmaceutical, Chemicals, Cosmetics, plastics, paints, plastic, minerals, rubber compounds, metal powders, detergents, pesticides and fertilizers, dyestuff and pigments Vibro sifter consists of a screen placed on the base plate attached centrally to gyratory motor. The material fed through the inlet located on the top is dropped on the screen. The particles smaller than the mesh size passes from the screen and the larger sized particles are released through an outlet. The combination of vibratory motor and the weights placed on top and bottom of screen gives the desired filtration or separation of the material. Total assembly is mounted on suitable springs so that it becomes an independent body which vibrates without parting any vibrations to the foundations. Salient Features : Design is cGMP - Current Good Manufacturing Practices compliance. All contact parts AISI 316 & non contact parts AISI 304. Powerful vibration by gyratory motion by special Vibro motor. Side outlet & fines discharge. Easy movable & clean. Noiseless operation. Lead free and Silicon seal sieve.   Optional Features : Inline loading/Milling process and transfer to bin/Blender by Vacuum transfer system. Double or triple deck sifting system

Brand Name : SSPM

Type : Other

Place of Origin : India

Application : Granules

This equipment is mainly used in industrial field to separates the materials in the combination of shape, size and density. It works by injecting the material stream to be sorted into a chamber which contains a column of rising air. Inside the separation chamber, air drag on the objects supplies an upward force which counteracts the force of gravity and lifts the material to be sorted up into the air. Due to the dependence of air drag on object size and shape, the objects in the moving air column are sorted vertically and can be separated in this manner. Air classifiers are commonly employed in industrial processes where a large volume of mixed materials with differing physical characteristics need to be separated quickly and efficiently. One such example is in recycling centers, where various types of metal paper plastics arrive mixed together and need to be sorted before further processing can take place.     Features:   Particles are reduced to finer and more uniform sizes. Use of cyclone separator leads to less dusting on output side. No dusting from feeding hopper because feeding is done under negative pressure. It runs at lower speed , hence it requires much less maintenance. They are easy to clean & wash. It is manually fed as normal practice & can be supplied with automatic feeding as well. It uses air classification which does not require screen. Hence, it is free from problems like conking, Printing & frequent replacement of screen do not arise.

Steam Separator are available in various sizes. Our steam separators also finds usage in saturated steam lines for separation and removal of moisture formed due to the heat loss. These steam separators are offered in different forms and are as simple as a baffle, which uses the inertia caused by a direction change. Cyclone separators & steam dryers are its integrated parts.

Material : Paper

Brand : Donaldson

Spare Type : Cylindrical

* Effective Separation of heavy & light material (Metal pieces, Pins, Plastics) from pulp. * Easy maintenance and minimum fiber loss. * The body is made out of mild steel with S.S. cladding. Special model is also available in S.S. 316 Sandwitch plate (S.S. and M.S.) with base frame and stifners in M.S. * A cyclone effect is formed in the separator by the S.S. Rotor, So heavy particle are carried outward by centrifugal force to the junk trap. The light rejection is further treated in secondary separator or vibrating screen.

3 Micron Borosilicate Glass Fiber media type Moisture Separator   This unique design 3 Micron Borosilicate Glass Fiber media type Moisture Separator is very effective for removal of Moisture from compressed Air. It prevents dirt, dust & water particles to be carried into the pneumatic system.   It is recommended to install this Separator just before application point for better performance.