Gate Valves Dealers in Sarkhej, Ahmedabad (20 products available)

CAST STEEL : STAINLESS STEEL

We offer gate valves are primarily designed to start or stop flow, and when a straight line flow of fluid and minimum flow restriction are needed. In service, these valves generally are either fully open or fully closed. The gate (also called wedge) of a gate valve is completely removed when the valve is fully open; the wedge is fully drawn up into the valve bonnet. This leaves an opening for flow through the valve at the same inside diameter as the pipe system in which the valve is installed. A gate valve can be used for a wide range of liquids and provides a tight seal when closed. advantages of using gate valves: good shutoff features gate valves are bidirectional and therefore they can be used in two directions pressure loss through the valve is minimal.

Material : SCS 13

Application : Waster Treatment Plants, Steel Plants

Size : 4 Inch

Suitable medium : Steam, Water

Temperature range : 29 Degree Celsius- 125 Degree Celsius

Condition : New

Manufacturing Standard : BS 5163 / IS14846

Size Range : 32 to 1500mm

Pressure Ratings : PN10, PN16

These valves are available in non rising as well as rising spindle type suitable for clear water up to 450 C. These valves are designed with total compliance with applicable design and testing standards. All designs are validated for stress analysis. Sluice valves find wide application in water works, water/effluent/sewage treatment plants. These valves are available in non rising as well as rising spindle type suitable for clear water up to 450 C. These valves are designed with total compliance with applicable design and testing standards. All designs are validated for stress analysis. Sluice valves find wide application in water works, water/effluent/sewage treatment plants. FEATURES Rigid and sturdy design Low pressure loss across the valve Suitable for clear water up to 45 C and 5000 ppm turbidity, other fluids with maximum pressure / temperature conditions within the scope of IS:14846 Long service life and leak-tightness even after thousands of open / close cycles APPLICATIONS Water works Water / Effluent / Sewage treatment plants Fire Fighting Power

Size Range : Class

2" - 24" : 150

2" - 16" : 300

2" - 12" : 600

2" - 12" : 900

2" - 6" : 1500

We are manufacturing valves under brand name SABA. We also dealing in ZED make manual valves and Aira, Rotex make Automation products.   We manufacture SABA make wide range of Gate Valves which include knife gate valves,forged and cast gate valves having screwed / Socket / Flanged Gate valves. These valves are renowned all over for their premium quality. With the quality assurance we are the largest flanged gate valves supplier in India. We also manufacture these gate valves according to customer specifications. The quality of these valves is intact. They are properly inspected and verified before sending them to client. Uses of acme quality metal and flawless designs which enhance the performance of these valves have made us stand much ahead from the other manufacturers in India.Gate Valves are Outside Screw & Yoke, Bolted bonnet & with Rising stem. The “STRAIGHT THROUGH BORE” design assures minimum turbulence, erosion and resistance to flow caused by pockets & recesses. Gate Valves are mainly used where minimum pressure drop is a requirement.Design Features : Designed for exceptionally low pressure drop Back seating arrangement permits the replacement of packing with valve under fully open condition. Two piece design of gland flange provides centralizing effect to the gland sleeve, thus producing a uniform clamping pressure on the packings. Material Structure : End Connection : Flanged end raised face, Butt weld end, RTJ, etc. Operation : Hand wheel, Gear operator, Electrical Actuator, Pneumatic, Hydraulic Shell :WCB, WC1, WC6, WC9, LCB, LCC, LC3, C5, C12, CF8, CF8M, CF3, CF3M, CF8C, CN7M, CD4MCu, Hastalloy, Inconel, Duplex Stainless Steel Trim :13% Cr. Steel, 304, 304L, 316, 316L, 321, 347, Monel, Duplex Stainless Steel Standards "Design Standard :  API 600 Testing Standard :  API 598 Face to Face :  ASME B 16.10 End Connection : Flanged End : ASME B 16.5 Butt Weld End : ASME B 16.25 Pressure Temperature : ASME B 16.34 Valve Operation :Operator : Hand Wheel : Size Range : 2” – 10” – Class 150, 300, 600 2” – 4” – Class 900 & 1500 Operator : Gear Operator Size Range : 12” & above – Class 150, 300, 600 6” & above – Class 900, 1500

Bore Sizes : 1-13/16

Temperature Class : K-V

Material Class : AA - FF

Working Pressure : 5000 PSI - 15000 PSI

Product specification Level : PSL1 - PSL3

Performance Rating : PR1 - PR2

Wedge Gate Valves of different ratings are offered by us. These valves have been designed for maximum efficiency and are corrosion resistant. They are available in different sizes for the client to choose from according to the applications. We deal primarily in bulk sized orders Marginal orders are also frequently processed by us as and when requested by our clients. Client satisfaction is our top priority.