Process Control Equipment Dealers in Coimbatore

Heat controllers are used for operating big machines by controlling their speed or heat using regulator. It can also be used to control multiple fans in a hall all at one time. It can be called as Fan controller, Machine Regulator.

We are one of the professional manufacturers of Solar Pump Inverter. It has become the leading products combining photovoltaic industry with traditional industry such as agriculture water conservancy, desert control, daily water supply, city landscaping, etc. System is widely utilized for agriculture irrigation, desert control, pasture animal husbandry, City landscaping, daily water supply, etc. The offered inverter is manufactured by using premium quality components with the use of ultra-modern techniques under the guidance of our adept professionals. Application Overview: Solar Pump Inverter, perfect solution to be free from power cuts. This pure solar inverter has peak efficiency and comes with in-built solar charge controller. With its slim design, solar pump inverter is suitable to install anywhere in your home and you can also run referigerator, cooler or air conditioner through this inverter. The advanced charging alogrithm, included monitoring software and built-in solar charge makes solar inverter a perfect solar inverter for any home. Scheme Above scheme does not show the interlocks for running the drive with three phase supply. External contactor logic will be required for changing from DC to AC supply. Safety interlocks and isolator must be used to isolate the drive from PV source are not indicated in this scheme. Product selection: Drive selection: Sx2000 drive (400V class) drive as per motor rated current. Total Vmpp = 560 to 610 VDC Ex. If Vmpp of one panel = 30V then total panels required are 600 V / 30 V = 20 nos. Under voltage level for 400V class drives is 360VDC Under voltage level for 200V class drives is 180VDC Total Voc should not be higher than 760VDC Impp = Motor kW * 1300 / Total Vmpp Impp = Motor FLC * 0.75   Please select Impp whichever higher from above formulae.   Proper enclosure shall be selected based on the site conditions.   In case drive to motor cable distance is higher than 150-200 feet, an AC reactor shall be used at the output of drive. Note:   If drive is required to be run on AC circuit then please refer technical manual of Sx2000 drive for AC side fuse ratings   I^2.t mentioned in above chart shall be referred, if different make of fuse is to be selected for the application.   Above ratings are for 400v class drives. Please contact beta for 200V class drives.   Terminologies Used:   MPPT: Maximum Power Point Tracking   Voc: Open circuit voltage of solar panels We are looking for queries for Beta power Equipment from Tamil Nadu, Kerala, Karnataka & Andhra Pradesh,allover india and exports.   Vmpp: Voltage at Maximum Power Point     Impp: Current at Maximum Power Point

CP series plc I/O capacity upto 1024   Self diagnostic function High speed operation 200ns/sec Max of 16 base expansion More than 300 instructions Separate communication port 16 bit processor CPU embedded pid function

Pearl is a semi-automatic model which suites for automatic OFF operation only.The pump must be switched ON manually. Both single & double tank sensing available control top tank or bottom tank. Available Indications Power On Pump ON Tank Full Sump Empty This model is suitable for Single Phase Borewell Pump 3 Phase Borewell Pump 3 Phase Monoblock Pump 3 Phase openwell Submersible pump

Temperature controller is a measurement device used on temperature control. Thermocouple-type and resistor-type temperature controllers measure temperature electronically, obtaining the temperature change from the sensor and sending the measured data to the electronic processor. The output device will then control the temperature variation within a specific range.Delta's DT series temperature controller has fast output response, accurate PID parameter auto-tuning, support Modbus communication protocol and is built-in with various output types, allowing different systems to reach a stable control status very quickly. Besides, all series are complied with international installation dimension and CE, UL international safety approvals.

Steatite Ceramic Terminal Block with Nickel Plated Terminals → Die cast Aluminium / S.S mounting head & adjustable flange → Ceramic protection tube type KER 610 with 60 % , 80% AI2O3 → Holding tubes made of SS 304/SS316 of 32 mm , 25mm , 20mm dia are used to hold ceramic sheath with head. → Type KER 710 – Recrystalised – High alumina tube with 99.9 % AI2O3 available in 24mm,20mm,15mm,10mm,8mm,6mm dia. → Type ‘R’ (Pt RH 13 % -Pt) & Type ‘S’ (Pt Rh 10 % -Pt) Are used to measure temperature upto 1400 Degree C / 1600 Degree C → Type ‘B’ (Pt Rh 6% - Pt Rh 30% or Pt 18) are temperature upto 1800 Degree C . Thermo element pair is protected by two or three ceramic sheaths of various types depending upon working Temperature and environmental conditions.Color monitor (800 x 600)

Conforming to international quality management systems, our product range is of unparalleled value. Being a client-centric firm, we are dedicatedly involved in making available quality Siemens Simatic PLC. Our Siemens simatic PLC is designed for easy operation, low maintenance and long service life. 

Feautures : Delay On Timer Cyclic Timer Dry Run / Over Load Protection ( Range 0.1A To 40A) (2 CT Coil) Dry Run Restart Timer Facility 2 Line LCD Display User Programmable Current & Voltage Setting Suitable for : All Three Phase Pump Starter

Customers should stay rest assured with us for the payment procedures. They can pay us conveniently through wide-ranging payment mediums. In order to deliver a flawless lot of products, we keep it in safe and secure place. We have developed all the in-house storage unit wherein we keep it to prevent from damaging factors.Features : Micro Controller based Electronic Earth stop motion stop unit. Working on earth sense principle. Sliver Back creel left, right, Front creel left, Right break & Doff status Monitor . Easy Installation and reduces machine down time. Maintenance Free. LED indication for power and relay status Initialization and Settings : Before Installation, Isolate the Supply. Connect the unit as shown in the diagram below. Operation : When the sliver break or doff are in fault the machine off relay is turned on, corresponding relays are turned on. Once sliver break is rectified the the machine off relay resumes and sliver break indicating relay resets when machine is turned on.

We provide our clients, tailored water level controller. The product is widely used in various industries and has following features/advantages: Ensures and monitors the water level in the over head tank Operates on conductivity principle No moving components Easy installation procedure Minimal operating maintenance Manual override switch provided Suitable for single phase / three phase system Solution for multi-tank / multi pump installations