Divine International Sadar Bazar, Delhi

Motorized / Manual. Imperial or Metric

Heavy gauge stainless steel tank sturdily fabricated and bright finished. Provides effective hydro-massage of arms, hips, legs, knees and feet. Mounted on heavy duty 10cm dia four ball bearing castors. Comes complete with removable inside aluminium Seat & Arm rest. Unit is fitted with a motorized turbine ejector and aerator on a spring loaded turbine elevator, digital thermometer, thermostate & immersion heater. Provided with drain pipe for emptying. Inside measurements of tank 90cm long x 50cm wide x 70cm deep. No plumbing required.

These Water distillers produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants. A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container. Made of heavy gauge stainless sheet inside and outside, with immersion type heaters. The still provides continuous supply of pyroxene free distilled water and is equipped with brackets for wall mounting plug and cord and connector. Available in following capacities:1) 2 Ltr/hour (wattage 2KW)2) 4 Ltr/hour (wattage 4KW)3) 6 Ltr/hour (wattage 4.5KW)4) 8 Ltr/hour (wattage 6KW)

  SS body,wall type or table type. Fitted with heavy duty elements. Available in various capacities from 2 Ltr/hour to 20 Ltr/hour

This bath is suitable to maintain constant desired temperature for heating flasks in Chemical Laboratories. Bath is double walled inside made of stainless steel & outer body made of mild steel sheet painted with attractive Epoxy coated. The gap between the walls is filled with glass wool to minimize the loss of temperature. The stainless steel nozzles are provided one for inlet and second for over flow of water. The top of the bath has concentric rings. Available in following sizes:a) 325*250*100 mm (6 holes of 3" dia.)b) 325*300*100 mm (9 holes of 3" dia.)c) 425*325*100 mm (12 holes of 3" dia.)Also available in single wall

A great portable equipment for measuring pH, mV(ORP), Conductivity, temperature, TDS, Dissolved Oxygen (DO), Salinity and turbidity.pH Range: 0 - 14 pH Resolution: 0.01pH Accuracy: ±0.01 pH ±1 digit Temp Compensation: 0-100°C (Manual) Calibration Manual mV (ORP) Range: 0 to ±1999mV Resolution: 1mV Accuracy: ±1mV ±1 digit Conductivity (EC) Range: 0 to 1000 mmho in 5 ranges Resolution: 0.01 umho Accuracy: ±0.5% FS±1 digit Cell Constant: Adjustable (0.4 to 1.5) Reference Temp.: Adjustable (25°C) Temperature: 0 to 100° C Resolution: 0.1° C Accuracy: ±0.5° C ± 1 digit TDS Range: 0 to 10,000 mg/litre Resolution: 10 mgs/litre Accuracy: ±1% FS ±1 digit DISSOLVED OXYGEN (O2) Range: 0 to 20 ppm Resolution: 0.1 ppm Accuracy: ±0.2 ppm ±1 digit Temp. Comp.: 10° C to 50° C (Manual) DO Sensor Gold/Silver Amperometric Calibration Manual SALINITY Range: 0 to 40 ppt Resolution: 0.1 ppt Accuracy: ±0.5% ±1 digit TURBIDITY Range: 0 - 100 JTU Resolution: 1 JTU Accuracy: ±3% FS ±1 digit Sample size: 30 mm glass tube Light: 6.8 V Tungston lamp Detector: Photodiode GENERAL Display 3 1/2 digit (LCD) Operation Temp. 0° to 50° C Housing Materials ABS briefcase Power Supply 230 V ±10%, 50 Hz AC, 9V Battery (Dry cell) Standard Accessories Include the following:pH electrode, Conductivity/TDS/Salinity probe , Temp. probe, DO probe, Set of DO membranes, Test tube for turbidity (3)

These Wash Bottles are made of Low Density Polyethylene, which gives these bottles a translucent & unbreakable character. Solutions can be poured easily by squeezing the bottle lightly. The cap is fitted with a flexible polyethylene delivery tube, which can be aimed wherever required.Material: Low Density PolyethyleneAvailable in following capacities:125ml, 250ml, 500ml, 1000ml

Voltmeters or ammeters in any voltage or current range available in round 65mm dia. Available both moving iron type or moving coil type.

This instrument is used for determining the normal consistency and setting times of cement and 'A' Class limes.The apparatus consists of a metallic frame bearing a freely movable rod with a cap at top, one vicat mould, split type and glass base plate and one set of needles one each initial needle, final needle and consistency plunger.

Also called Mould Vibrator Or Mortar Cube Vibrator.Concrete moulds are easily cast by using a tamping bar or a vibrating table. However air tapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a vibrating machine. Vibration machine is used for the preperation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat portland cement, portland bleast furnace cement and high alumina cements.The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an intergral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm mould. The frequency of vibration is 12000 400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1min and certificate of vibration from a standard laboratory.Spares : Set of Springs, Belt and Belt guard.

The outer chamber is made of thick gauge Mild Steel while inner is made of 304 grade Stainless Steel. Lid is made of Mild Steel with inside lined with S.S. for double protection. The unit has Radial Locking arrangement for the lid. Provided with built-in safety valve, pressure guage, pressure release valve. Pressure is adjustable from 5 psi to 20 psi ± 3 psi. To operate 220 volts single phase 50 cycles. Working Temperature : 121° CStandard Controls:1) Double safety radial locking arrangement. 2) Stainless steel steam release valve. 3) Spring loaded safety valve of SS(grade SS-304) 4) Water inlet and water outlet valves. 5) Water level indicating gauge glass with SS guard. 6) Pressure guage. 7) Foot paddle lifting device.8) Electrical control box, fitted with toggle switch, indicating Neon lamps and steam release valve. Available in following sizes (Working Chamber):Height X Dia 450mm X 250mm (22 liters)500mm X 300mm (50 liters) 550mm X 300mm (78 liters) 600mm X 450mm (98 liters)750mm X 550mm (152 liters)Optional Accessories :1) Automatic Pressure Control Switch2) Automatic Water Cut-off Device3) Temperature Indicator (Dial Type)4) Mechanical Timer with Alarm System5) Digital Temperature Indicator

These are double walled cylindrical units with outer made of M.S. sheet duly enamel painted and Inner made up of heavy gauge S.S. Sheet. Gap between the two walls is duly filled with high grade glass wool to avoid thermal loss. Temperature range from 50 ° C to 150 ° C is Controlled by heavy duty thermostat with an accuracy of ± 1 ° C. It is capable of withstanding a high vacuum. Provided with vacuum gauge, see through transparent window of toughened glass and one shelf. To work on 220/230 volts A.C. supply. But without Vacuum pump. Available in following sizes:a) 200 x 200 mm b) 250 x 250 mmc) 250 x 300 mm d) 300 x 300 mm e) 300 x 500 mm

Adding to the already existing range of autoclavable laboratories trays, is the Utility Tray and as the name suggests this Polypropylene Tray can be utilized for purposes ranging from drying glassware to sterilizing and to store any laboratory apparatus. Size 375X350X130mmMaterial: Polypropylene

Motorized / Manual for single yarn and Double Yarn.

Counter For Counting ends and picks per inch or per cm

As Per IS:2386 (Part-1)Used for determining the flakiness index of aggregates. It consists of a frame with a sliding panel. The panel has slots of different standard lengths and widths accurately cut.

Thermal Stability Test Apparatus is used to measure/ check Thermal stability of PVC insulation & sheath of Electric cables as per IS:5831.Measures Thermal stability time in minutes required to change the pH value of 5 to 3 of a universal indicating pH paper placed in a glass tube containing sample and heated in a thermostatically controlled heating chamber at specified temp. of 200°C ±0.5°C.New Model incorporates a specially designed heating block which eliminated use of expensive silicone oil as in a conventional model.

Upto 500 kg. Capacity with 3 subclass. Grips of different sizes available. Can be used for lea strength (yarn) also.

elemendorf Type - upto 6400 G.

Monocular body, tube inclinable up to 90 degrees. Mechanical tube length 160mm. Plain square stage of 120 x 120mm with two stage clips. Fitted with double lense condenser N.A.1.2 with iris diaphragm and swing out filter holder. Plano concave mirror in fork mount. Triple revolving nose piece for quick change of magnification with accurate click stop for perfect parafocal alignment. Eye Pieces uygenian 10x & 15x. Parafocal achromatic objectives 10 x 45x/40x(S.L.) having total magnification 100x - 600x/675x . Complete in Thermocol Box.

  For determining Stripping Value of bitumenous mixes having aggregate size 1.0mm to 75 microns.A circular tray rotates in a vertical plane at a rate of approximately 100 r.p.m. by an eletrical geared motor. 4 bottles of approximately 400 cc are mounted on this circular tray at an angle of 90° to each other with their mouths towards centre of the tray.A time switch is provided. Suitable for operation on volts A.C. single phase.

Used to determine grade of bitumen. The penetration tests determine consistency of bitumen for the purpose of grading. Depth in units 1/10 of millimeter to which a standard needle having a standard weight will penetrate vertically in a duration of five seconds at a temperature of 25ºC determines penetration for gradation.It consists of a vertical pillar mounted on a base provided with levelling screws. The head, together with dial plunger rod and cone (or needle) slides on a pillar and can be clamped at any desired height. A rack & pinion and pointer assemble provides fine adjustment of needle or cone tip to sample. It incorporates a clutch mechanism which makes reading of penetration and subsequent resetting a simple and accurate operation. The dial is graduated in 400 1/10 and the millimeter sub-divisions and the needle pointer against figures makes easy reading. Supplied with bitumen penetration needle, ring weight one each 50 gms, and two sample container.Accessories : Penetration cone for empirical estimation of penetration of lubricating grease, petroleum jelly etc.

The apparatus consists one each of Compaction Mould Gun Metal, 100 mm I.D. x 127.3 mm height x 1000 cc. volume, complete with collar and base plate. Rammer 2.6 kg x 310 mm controlled fall.

Stack Monitoring Kit Consisting as follows:1) Temperature Range Ambient to 600°C2) Set of Inter Connection Hoses Pipes.3) Double Wall Cold Ice Box.4) Rotary Van type Vacuum pump Cap. 100 LPM.5) Dry Gas Meter Assembly.6) Velocity measuring Kit 7) Pitot Tube. 1-meter length. 8) Thermocouple.9) Glass Impingers No. 2, as a condenser & 3 No for sampling. Rotameters. 3 LPM for Gases and 100 LPM for Stack.Accessories 1. Impinger 275 ML: 01 No.2. Impinger 150 ML: 01 No.3. Thimble paper Pkt. of 25 Nos. 01 No.

These Storage Boxes, made of Polypropylene, prove to be an excellent option for storage of different powdered reagents & other material in the laboratory. Square shape of these boxes help in saving shelf space. Available in two different sizes, these boxes have polypropylene caps, are autoclavable, provide good chemical resistance & heavy duty service.Material: PolypropyleneAvailable in 250ml, 500ml, and 1000ml