International Equipments Kanjurmarg, Mumbai, Maharashtra

Highly accurate position control with high range of speed Accurate start and stop instanatly using 32 bit microcontroller Four line and 20 characters controller with multiple features Automatic calculation of modulus @different strains selectable Multi unit display in Kg, pound, Newton mm, cm, inch selectable Direct display on controller and numeric printout facility Safety norms of over load in auto as well as manual mode Safety norms of over travel in auto mode. Tests preprogramming facility for Tensile, Flexural, Peel, Bond, Compression, Cyclic endurance based on load, travel, time Data lock for calibration and master controlled parameters

Tensile testing is a most significant and popular test procedure which is performed in different production verticals to measure the elongation strength and durability of the products. Tensile Testing is also known as Tension Testing, This test shows at what point sample fails when an extensive amount of tensile force is applied to the sample. It helps the engineers to measure the maximum force a material can tolerate to its maximum before it brakes and helps to decide the suitability of the material for a particular application. The tensile test is performed using a high-quality testing machine known as Tensile Tester or Tensile Testing Machine to determine properties of tensile and elongation as per ASTM D - 638 / ASTM D – 882 of plastics – Eco version. Specification: Load capacity : up to 500 kg*. No. of load cell : One. Cross Travel : Up to 1000mm*. Speed : Variable between 10mm/minute to 500mm/minute. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Direct display through microcontroller : Peak load, Area and Tensile strength at peak load.

Specification: Temperature Controller: Digital PID Controller with range up to 300°C, Resolution of 0.1°C & accuracy of +0.5°C. Pan: 500 Nos. of aluminium pans with 40 mesh screen in SS 316 will be provided as per DOT specification. Gas Flow Control: Gas Regulators & Rotometers will be supplied for Nitrogen & Oxygen Gas respectively. Indium material will be supplied for Calibration of temperature. PRINTOUTS THROUGH PC: The display & printout of Delta Temperature Vs Time graph along with Oxidation Induction Time result is Possible through your PC. The printout includes Party’s Name, address, file name, date, batch no, Operator name, Sample weight, Set temperature, Start time, Finish time, Gas flow rate etc. Calibration graph of melting point of indium metal along with printout facility is provided as per DOT Specification. Cooling System: Cooling of barrel by water is provided.

Rated Power : 230 Volts, 50Hz, single phase.

or making ‘V’ notch in the Izod / Charpy samples as per ASTM D – 256. Specification: Depth micrometer : “Mitutoyo” make. Range : 0 – 25mm with least count of 0.01mm. Cutting angle : 45º. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase.

Micro Controller based Computerised Hydrostatic Pressure Testing as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition.

Power : 230 Volts, 50Hz

Specification: Microcontroller with alpha numeric key pad having built-in temperature controller with temperature range up to 400 degree centigrade, resolution of 0.1 degree Centigrade and accuracy of +/- 0.1 degree Centigrade similarly built-in timer with range 999.9 seconds. Piston Travel: Up to 25 mm & resolution of 0.02 mm. Specimen cutting: Motorized. Specimen Weighing: Automatic up to 60 gm and resolution of 1 mg. Weight: 0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg & 21.6 kg hard chrome plated weights. Digital Display: Individual MFI, MVR, Melt Density results & average results. PC output: Through serial port with Window 7 compatible software. Accessories: Standard accessories*. Paint: Powder Coated. Power Supply: 230 Volts, 50 Hz, Single Phase.

as per Tappy T – 815 standard to determine the coefficients of friction between film to film, film to metal and film to glass.

Power : 230 Volts, 50Hz, single phase.

as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition. Pressure range : 0 – 100 bar*. No. of stations : 8 nos. Pressure input : Through compressed air having pressure upto 5 kg/cm.sq Pressure output: through hydro-pneumatic pump. Time range : 0 – 999.9 hours. Panel mounting : Trolley with castor wheels. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Direct display through MMI : Set pressure, Actual pressure, Set time, Actual time, Set temperature and Actual temperature. Graphic display and printout through PC : In addition to the above values Pressure & Temperature Vs Time graph could be obtained for any station by attaching a printer to the PC.

to cut samples having thickness up to 4mm.

Capacity : 5 tonnes*.

to determine the effect of relative humidity on sample at various temperatures. Computerised Humidity chamber to determine the effect of relative humidity on sample at various temperatures. Material of construction : Inner bath: S.S                                     Outer body: M.S Direct display and printout through microcontroller : Set RH, Actual RH, Set temperature and Actual temperature. Graphic display and printout through PC: In addition to the above values, % RH and Temperature Vs Time graph could be obtained by attaching a printer to the PC.

Power : 230 Volts, 50 Hz, Single phase.

Humidity range : 20% RH to 95% RH.

with radial air circulation and auto shut facility. Specification: Size of working chamber : 12 inch X 12 inch X 12 inch*. Material of construction : M.S. Temperature range : Ambient to 250ºC. Air circulation : Radial fan (It saves power at least 20% by re-circulating the same hot air inside the oven). Timer : Digital presettable with range upto 999 minutes. Paint : Powder coated. Power supply : 230 Volts, 50Hz, single phase.

Specification: Temperature zone: Two. Controller: Auto tuned PID controller with temperature range up to 200 deg C having resolution of 0.1 degree centigrade. Clamping Jaws: One fixed and second movable by pneumatic action. Day light: 50 mm. Sealing dimensions: Length 150 mm x Width 20 mm. Mounting: Table top. Power requirement: 230 Volts, 60 Hz, Single phase – 15 ampere.

Specification:   Temperature range : From ambient to 300ºC. No of stations : Three. Material of construction : Inner bath: S.S                                     Outer body: M.S Rate of heating : 120ºC / hour and 50ºC / hour. Sensor : Range upto 10mm with resolution of 0.01mm. Weights : A set of weights ranging from 5grams to 2000grams would be supplied for incremental loads. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Graphic display and printout through PC: Penetration/Deflection Vs Temperature graph and numeric reports consisting values of vicat softening temperature and heat deflection temperature could be obtained by attaching a printer to the PC.

for conditioning of pipes for impact test as per IS 4984 and IS 12235 (Part 9). Material of construction : Inner bath : S.S                                     Outer Body : M.S

Power : 230 Volts, 50 Hz, single phase.

to check the adhesive strength between two samples. Specification: Load capacity : Up to 5 kg.* No. of load cell: One. Cross Travel : Up to 250 mm* Speed : 300 mm/minute. Direct display : Peak load. Paint : Powder coated. Power : 230 Volts, 50 Hz, single phase.

We are offering digital opacity tester .

Power : Single Phase.

Power : 230 Volts, 50 Hz, single phase

International equipments developed the first dart impact tester way back in year 1971 as per the ASTM D 1709 and IS 2508 standard. This equipment is mainly designed to check the impact failure weight of film and sheeting by a falling weight impact method. In addition to dart impact tester other equipment such as coefficient of friction, tensile tester, heat sealer, opacity tester, melt flow index tester, peel bond tester are also offered by international equipments Specification: Dart : 2 nos. Weights : A set of weights ranging from 5 grams to 500 grams would be supplied for incremental loads.

Power : 230 Volts, 50 Hz, single phase.

Speed of cutting: Adjustable through AC variable drive. Minimum & maximum dimensions of specimen: 5 mm to 25 mm One number of Template for ASTM D 638 Type I for tensile would be included in the supply with this equipment. Additional vacuum system will be provided for collection of waste material during test.

Specification:   Capacity : Up to 25.00 Joules. Release angle of pendulum: 150 degree. Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules. Minimum resolution on scale: 0.02 Joule, 0.05 Joule, 0.1 Joule, 0.2 Joule and 0.2 Joule respectively. Paint : Powder coated. Power : 230 Volts, 50Hz, single phase. Direct display through microcontroller: Impact strength in joules/meter and kg-cm/cm. Graphic display and printout through PC: Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.

Power : 230V, 50 Hz, single phase.

as per ASTM D 1603, IS 4984 and IS 2530 to determine carbon black content of plastics. Accessories : Desiccator, Glass U tube, Combustion tube, Combustion boat, Rotometer, Rubber tube [1 no. each], Glass end caps – 2 nos. and Glass traps – 3 nos.

Power : 230 V 50Hz, single phase.