Pumping Unit Dealers in Mumbai

This unit for constant Press & temperature to BurnerYou can save your oil Consumption & Timing. Increase of your products   This units made in Two Model: Simplex Model Duplex Model   Simplex Model :- One Motor with Oil gear Pump ,One Oil Heater 2kw. & Above (As per Required)Oil Filter, Pressure Gauge, Tempercher Gauge,Pressure relies valve & Pressure ValveAssemble on Ms. Tray   Duplex Model:- Two motor with two gears Pump.One oil Heater 2 kw. & Above (As per Required)Two Oil Filter Pressure Gauges, Temperchar Gauge,Pressure relies valve & Pressure Valve.Assemble on Ms. Tray.

Furnace oil is best stored in cylindrical tanks either above or below the ground. Generally, the main storage tank is erected above ground when the capacity exceeds 70,000 litres. For lower capacities, underground storage may be more economical. When erecting a storage tank above ground, remember to maintain safety distances from the surrounding structures, as prescribed by the Explosives Department.   Storage tanks are generally made from welded mild steel plates. The overhead tank should be mounted on concrete blocks, which provide a slight gradient of 1:50 towards the drain valve.   Each of the following fittings has a definite role to play. The Outlet or Draw-Off Pipe should be located at the raised tank end, not less than 15 cms. from the bottom. The Vent Pipe, of gooseneck type, should be located at the highest point of the tank to facilitate filling by venting air and oil vapour during the filling operation. It should be at least 5 cms. in diameter and provided with a strainer at the outlet. The Fill-Pipe could be located either at the top or at the bottom of the tank. If located at the top, it must be ensured that the pipe descends almost to the bottom of the tank.When located near the bottom, it is important to position a non-return valve on the line to avoid furnace oil re-entry into the tank-truck on account of back pressure. To avoid leakage of oil during decanting, it is advisable to have a camlock coupling at the filling end so that it fits snugly on the delivery hose. The Drain Pipe, which is fitted at the lower tank end bottom, is used top periodically remove the accumulated water. It is a difficult task to drain the water and sludge from underground storage tanks. The water and sludge which settle down at the bottom should, however, be removed by a handpump. It would be advantageous to have two suction pipes-one at a lower level and the other at a higher level-so that in case the sludge accumulation is up to the lower point and the suction line chokes up, the alternative line could be put into operation and adequate time would be available to decide upon a time schedule for cleaning the tank. Furnace oil as delivered may contain dust, dirt, gummy matter and water. During storage for prolonged periods, these tend to form sludge which accumulates in the various ‘dead spaces’ of the tank, where the oil is not agitated during normal operations of the tank. This results in unsteady flames and clogging of filters. To avoid this, some means of agitation of oil in the tank may be necessary   In addition to the main storage tank(s), industries may have one or a number of day service tanks located in proximity to the units consuming oil. The principles enumerated earlier for the maintenance of main storage tanks apply here too. The service tank may be sized for a shift’s consumption or daily consumption-the choice depends on capacity required, ease of location of tank near the shop, pumping capacity, horse power, etc. certain additional precautions may, however, be taken with respect to service tanks: a) Service tanks should not be located very near or above furnaces, hot air or process ducts, etc. b) They may be provided with overflow pipes which lead directly below to a sump. As a further refinement, limit switches could be provided to avoid the possibility of oil overflow. c) In gravity feed systems, the difference in height between the service tank and the burners should be at least 10 metres. Removal of contaminants Furnace oil should be free from possible contaminants such as dirt, sludge and water before it is finally fed to the combustion system. Furnace oil arrives at the factory site either in tank lorries by road or by rail. Oil is then decanted into the main storage tank. To prevent the possibility of contaminants such as rags,cotton waste,loose nuts or bolts or screws from entering the system and damaging the pump, position a coarse strainer of 10 mesh size (not more than 3 holes per linear inch) on the entry pipe to the storage tanks. Progressively finer strainers should be provided at various points in the oil supply system to filter away finer contaminants such as external dust and dirt, sludge or free carbon. It is advisable to provide these filters in duplicate to enable one filter to be cleaned while oil supply is maintained through the other. Figure below gives an illustration of the duplex system of arrangement of strainers.

• Application: All
• Condition: Good
• Country of Origin: Mumbai
• Brand Name: Pump - Aid
• Fuel: Electric

We are a reputed manufacturer and wholesale supplier of Pumping Unit from Mumbai in India. We offer Pumping Units manufactured using latest technology to meet your growing requirements. We ensure our Pumping Units conform to international performance and safety standards and are dependable and require minimal maintenance. These efficient Pumping Units used in various industrial processes are custom built to suit your requirements using superior quality materials.

• Number Of Flower: Rotary Vane Pump Twin Lobe Pump Combination
• Material: Metal
• Packaging Type: Silver and Black
• Application: Evaporative Concentration, Vacuum Distillation, Polymerization
• Packaging Tye: Standard Packaging
• Energy Efficiency: Highly Energy Efficient
• Power Consumption: Low

We bring to you the best range of vacuum pumping unit and high vacuum pumping unit. In addition, we are known as principal vacuum pump unit manufacturer & supplier in the industry. In case single vacuum pumps (liquid ring pumps, rotary vane pumps) are not suited for a certain process due to their pumping speed and / or their ultimate vacuum, a combination with twin lobe pumps can be used. these vacuum pumping units consist of rotary vane pump twin lobe pumps as fore-pump and rotary vane pump or liquid ring pump as backing pump. The fore-pump picks up oil necessary for its lubrication from the backing pump. The exhaust from the fore - pump is connected to the suction side of the backing pump thereby giving advantage of high pumping speed at higher vacuum. These units are highly energy efficient and consume less power than conventional single vacuum pumps. these pumping units are of compact design and mounted on base frames ready for use. They are tailor - made and are offered to suit user's requirements. applications : evaporative concentration, vacuum distillation, polymerization, crystallization, vacuum impregnation, vacuum drying, sterilization, vacuum cooling, object metallising, roll metalllisation, semi-conductor processing, manufacture of vacuum & microwave tubes, manufacture of gls automotive& miniature lamps, tube light production, sintering, brazing, electron beam welding, heat treatment ionic nit riding, tool coating, vacuum casting, degassing & refining, plasma welding, evaporation, sputtering, space research and development applications.

In case single Vacuum pumps (liquid ring pumps, rotary vane pumps) are not suited for a certain process due to their pumping speed and / or their ultimate vacuum, a combination with twin lobe pumps can be used. These Vacuum Pumping Units consist of rotary vane pump twin lobe pumps as fore-pump and rotary vane pump or liquid ring pump as backing pump. The fore-pump picks up oil necessary for its lubrication from the backing pump. The exhaust from the fore - pump is connected to the suction side of the backing pump thereby giving advantage of high pumping speed at higher vacuum. These units are highly energy efficient and consume less power than conventional single vacuum pumps.  These pumping units are of compact design and mounted on base frames ready for use. They are tailor - made and are offered to suit user's requirements. APPLICATIONS :- Evaporative Concentration, Vacuum Distillation, Polymerization, Crystallization, Vacuum Impregnation, Vacuum Drying, Sterilization, Vacuum Cooling, Object Metallising, Roll Metalllisation, semi-conductor Processing, Manufacture of Vacuum & Microwave Tubes, Manufacture of GLS Automotive& Miniature Lamps, Tube Light Production, Sintering, Brazing, Electron Beam Welding, Heat Treatment Ionic Nit riding, Tool Coating, Vacuum Casting, Degassing & Refining, Plasma Welding, Evaporation, Sputtering, Space Research and Development Applications.

Nitrogen Pumping Unit, Skid Uni

Pumping Unit, Cyclone Separator, Air Blower, Heating Unit, Oil Filte

Oil Pumping Units, Atomizer Burner, Oilgear Pumps, Oil Line Heater

Heating Pumping Units, Non Ibr Boilers, Modulating Motors, Burner Gun

Pumping Units, Power Hammer, Pneumatic Tools, Hammers, Power Pres

Pumping Unit, Industrial Burner, Gate Valve, Chain, Gi Metallic Hose Pip